Search Results

1 An all fiber-optic sensor has been developed to measure H2O mole fraction and gas temperature in an HCCI engine. This absorption-spectroscopy-based sensor utilizes a broad wavelength (1320 to 1380 nm) source (supercontinua generated by a microchip laser) and a series of fiber Bragg gratings (19 gratings centered on unique water absorption peaks) to track the formation and temperature of combustion water vapor. The spectral coverage of the system promises improved measurement accuracy over two-line diode-laser based systems. Meanwhile, the simplicity of the fiber Bragg grating chromatic dispersion approach significantly reduces the data reduction time and cost relative to previous supercontinuum-based sensors. The data provided by the system is expected to enhance studies of the chemical kinetics which govern HCCI ignition as well as HCCI modeling efforts.

A mobile and dispersed power system is necessary for an advanced technological-industrial society. Today's petroleum-based system discharges waste products and heat and is growing exponentially. Energy resource commitment has already intersected “ultimate” low-cost petroleum supplies in the United States and will do so for the world before 2000; this portends major changes and cost increases. The twenty-first century system for mobile-dispersed power will reflect the energy source selected to replace petroleum-for example, coal, solar insolation, or uranium. It will incorporate a fuel intermediate such as methanol, ammonia, or hydrogen, and a suitably matched “engine.” The complete change will require more than 25 years because of the magnitude, fragmentation, structural gaps, complexity, and variety of the mobile-dispersed power system.

In this work a detailed model to simulate the transient behavior of catalytic converters is presented. The model is able to predict the unsteady and reacting flows in the exhaust ducts, by solving the system of conservation equations of mass, momentum, energy and transport of reacting chemical species. The en-gine and the intake system have not been included in the simulation, imposing the measured values of mass flow, gas temperature and chemical composition as a boundary condition at the inlet of the exhaust system. A detailed analysis of the diffusion stage triggering is proposed along with simplifications of the physics, finalized to the reduction of the calculation time. Submodels for water condensation and its following evaporation on the monolith surface have been taken into account as well as oxygen storage promoted by ceria oxides.

Methanol fuel was tested in a prototype 2-cycle ceramic heat insulated engine with a swirl chamber. It was found that the 2-cycle ceramic heat insulated engine with a compression ratio of 18:1 could ignite methanol without an auxiliary ignition system and emissions were substantially reduced in the whole load range.

Aircraft potable (drinking) water systems haven’t changed significantly in the last half-century. These systems consist of cylindrical water tanks pressurized by bleed air from the jet engines, with insulated stainless steel distribution lines. What has changed recently is the increase in the possibility of aircraft picking up contaminated drinking water at foreign and domestic stops. Customer awareness of these problems has also changed - to the point where having reliable drinking water is now a competitive issue among airlines. Old style potable water systems that are used on modern aircraft are high maintenance and exacerbate the growth of microbes because the water is static much of the time. The integrity of some pressurized water tanks are also a concern after years of use. Cost-effective mechanical and biological solutions exist that can significantly reduce the amount of chemicals added and provide good potable water.

Starting with the laboratory study, the amount of exhaust emission compound dissolved in water was measured, and the divergence of exhaust emission compounds was reviewed. Measurements were taken for hydrocarbon (HC), especially benzene, toluene, m-Xylene, p-Xylene, and o-Xylene. It was verified that the amount of exhaust emission compounds dissolved in water has positive correlation with the volume of exhaust gas introduced into the water. The dissolved amount was smaller with the low emission engine model. Volatile Organic Compound (VOC) decreased sharply at the beginning, but the decrement got smaller after a certain period of time. Next research was performed on the actual river where PWC are being used. We looked into the possible correlation between the VOC's concentration in water and the distance to the water where a lot of PWC's are running. In addition the MTBE (Methyl Tertiary-Butyl Ether) concentration was measured.

When evaluating the sound generated by PWC (personal water craft), it is essential to study the measurement method for the PWC sound itself. However, it is equally important to identify the influence on the people in the neighbor of shoreline by being exposed to the sound from a group of PWC running around on waters. Such influence can be grasped in relation to the results of sensory evaluation. LAeq (equivalent continuous A-weighted sound level) was measured on PWC's running in various patterns and different numbers, while sensory evaluation was performed to obtain the data for the feelings the exposed persons would have about the sound. In this way the correlation between the sound pressure level and its perception by the people were analyzed. LAeq is the mixture of natural sound at the test site and the sound from the PWC(s) running in the predetermined patterns.

A 3D-CFD model with detailed chemical kinetics was developed to investigate the combustion characteristics of HCCI engines, especially those fueled with hydrogen and n-heptane. The effects of changes in some of the key important variables that included compression ratio and chamber surface temperature on the combustion processes were investigated. Particular attention was given, while using a finer 3-D mesh, to the development of combustion within the chamber crevices between the piston top-land and cylinder wall. It is shown that changes in the combustion chamber wall surface temperature values influence greatly the autoignition timing and location of its first occurrence within the chamber. With high chamber wall temperatures, autoignition takes place first at regions near the cylinder wall while with low surface temperatures; autoignition takes place closer to the central region of the mixture charge.

AS speeds and operational altitudes of modern aircraft continue to increase, it is becoming more and more important that the total drag of the airplane be reduced while the rate of heat dissipation per unit frontal area of radiator be kept as high as possible. The standard method of increasing the temperature difference between cooling medium and coolant has been to use ethylene glycol as a coolant, because its boiling point is much higher than that of water; however, in its pure state glycol has various disadvantages that are not present when a pressure water system is used. This is a sealed system for making use of the physical characteristics of the increase in boiling temperature with pressure. When the radiator receives more heat from the engine than it is dissipating, a small quantity of steam is generated inside the cylinder jackets. The resulting increase in pressure will cause the temperature to rise until a balance is restored between heat rejection and radiator dissipation.

The traditional method for sampling vehicle exhaust has been the constant volume sampler (CVS) technique as described in the Code of Federal Regulations (CFR). This method dilutes the entire exhaust output from the vehicle, meters the mixture, and takes a proportional sample for measurement. The Mini-diluter sampling method reverses this process by first metering a small sample and then diluting to a fixed dilution ratio. This approach offers new opportunities to improve the quality of the sample measurement. This is especially interesting considering the lower emissions levels from ULEVs. The usefulness of this idea will depend on the development of stable and repeatable devices to implement it. This paper describes the operation of and presents results from a Mini-dilution system that uses critical flow venturis to provide a stable and repeatable dilution.

This work presents the implementation and validation efforts of a 3D ice accretion solver for aeronautical applications, MESS3D, based on the advanced Messinger model. The solver is designed to deal with both liquid phase and ice crystal cloud conditions. In order to extend the Messinger model to 3D applications, an algorithm for the water run-back distribution on the surface was implemented, in place of an air flow stagnation line search algorithm, which is straightforward in 2D applications, but more complicated in 3D. The developed algorithm aims to distribute the run-back water in directions determined by air pressure gradients or shear forces. The data structure chosen for MESS3D allows high flexibility since it can manage the necessary input solutions on surface grids coming from both structured and unstructured solvers, regardless the number of edges per surface cells.

As humans move into outer space, need for air, clean water and food require that green plants be grown within all planetary colonies. The complexities of ecosystems require a sophisticated understanding of the interactions between the atmosphere, all nutrients, and life forms. While many experiments must be done to find the relationships between mass flows and chemical/energy transformations, it seems necessary to develop generalized models to understand the limitations of plant growth. Therefore, it is critical to have a robust modelling capability to provide insight into potential problems as well as to direct efficient experimentation. Last year we reported on a simple leaf model which focused upon the mass transfer of gases, radiation/heat balances, and the production of photosynthetically produced carbohydrate. That model indicated some of the plant processes which had to be understood in order to obtain parameters specific for each species.

A hydrogen economy is an increasingly popular solution to lower global carbon dioxide emissions. Previous research has been focused on the economic conditions necessary for hydrogen to be cost competitive, which tends to neglect the effectiveness of greenhouse gas mitigation for the very solutions proposed. The holistic carbon footprint assessment of hydrogen production, distribution, and utilization methods, otherwise known as “well-to-wheels” carbon intensity, is critical to ensure the new hydrogen strategies proposed are effective in reducing global carbon emissions. When looking at these total carbon intensities, however, there is no single clear consensus regarding the pathway forward. When comparing the two fundamental technologies of steam methane reforming and electrolysis, there are different scenarios where either technology has a “greener” outcome.

Airline tenants at Dallas/Fort Worth International Airport (DFW Airport) use deicing/anti-icing chemicals, as may be needed, to maintain wintertime operations. DFW Airport has implemented best management practices for pollution prevention measures relating to deicing/anti-icing activities. However, as the planes leave the deicing pads, deicing/anti-icing fluids can drip from the planes onto the runways, taxiways, and ramp areas. As planes take off, the fluids can also shear off onto Airport property. During winter storm events, these deicing/anti-icing fluids are flushed off the runways, etc., with the stormwater. Stormwater containing deicing/anti-icing fluids can discharge through outfalls into Trigg Lake located in the southwestern part of the DFW Airport property.

Catalytic combustion coupled with activated carbon and molecular sieve adsorbents is applicable to all areas of air and gas clean up ranging from high to low levels of pollutants and trace contaminants control in a spacecraft environment is of no exception. In this study we propose a combined activated charcoal and catalytic combustion system based on a 70 watt power input achieving 350°C, operating on a 6 hour per 24 hour day catalytic cycle with an actual flow of 10.6 l min-1 in a residual free volume of 60 m3.

The Coast Guard has a primary duty to administer laws and promulgate and enforce regulations for the promotion of safety of life and property on the high seas and on waters subject to the jurisdiction of the United States. The rapid expansion of undersea activity indicates a need for government regulation without waiting for a disaster to provide the impetus. The expected Coast Guard relationship to civil submersible safety is discussed from the standpoint of legislation; preparation, promulgation and enformcement of regulations; duplication of efforts by other organizations; and avoidance of unnecessary interference with use of new developments and technical advancement.

The paper discusses the concept, specification and overall performance of a 10 kW electric power range extender suitable for electric plug-in and series hybrid vehicles, based on a single cylinder, high speed, four stroke internal combustion engine, tested and developed at Istituto Motori CNR of Italy. This unit has been conceived from the beginning as a compact on board recharging system for the mentioned kind of means, and especially for city cars and small commercial vehicles. The paper starts by defining some characteristics, advantages and drawbacks of an electric city car, followed by the criteria adopted to characterize the nominal power of the range extender. Then, the ratio which leaded to the adoption of a single cylinder internal combustion engine is discussed, followed by an explanation of the main design characteristics of the whole unit.