Search Results

The work reported in this paper has been conducted by a team from GE-Aircraft Engines, GE-CR&D, and Sundstrand under a contract sponsored by the USAF, Wright Laboratories, WPAFB, Contract No. F33615-90-C-2052. The objective of this contract is to prove the feasibility of an Integral Starter/Generator (IS/G) through the preliminary design stage and demonstrate the starter/ generator technology in the externally mounted version utilizing switched reluctance machine technology. This paper will report on the progress for the EIS/G-system through the initial testing stage. Comparison of the finished hardware with the design results presented earlier will lead of the paper. This is followed by the discussion of the early testing results for the system testing. Recommendation on additional testing will be presented at the end of the paper.

This paper describes the design, implementation, and performance test results of an engineering model of the Position Multiplexer (MUX)-Analog Input Processor (AIP) System for the transmission and continuous measurements of Reflector Control Drive position in SP-100. The specially tailored MUX-AIP combination multiplexes the sensor signals and provides an increase in immunity from low frequency interference by translating the signals up to a higher frequency band. The modulated multiplexed signals are transmitted over a single twisted shielded cable pair from the reflector drives located near reactor to the AIP located at the power conditioning/system controller end of the space craft boom. There the signals are demultiplexed and processed by the AIP, eliminating the need for individual cables for each of the twelve position sensors across the boom.

Recent Generic Flight System (GFS) updates have necessitated revisions in the initial startup and restart control strategies. The design changes that have had the most impact on the control strategies are the addition of the Auxiliary Cooling and Thaw (ACT) system for preheating the lithium filled components, changes in the reactivity worths of the reflectors and safety-rods such that initial cold criticality is achieved with only a small amount of reflector movement following the withdrawal of the safety-rods, and the removal of the scram function from the reflectors. Revised control and operating strategies have been developed and tested using the SP-100 dynamic simulation model, ARIES-GFS. The change in the total reactivity worths of the reflectors and safety-rods has eliminated the need for the use of fast and slow reflector drive speeds during the initial on-orbit approach to criticality.

The term “SP-100” is synonymous with a set of technologies that can be utilized to provide long lifetime, reliable, safe space power over the range of kilowatts to megawatts [1] using a nuclear reactor as the heat source. This paper describes recent development progress in a number of technology areas such as fuel, materials, reactivity control mechanisms and sensors. Without exception, excellent technical progress is being accomplished in all areas under development to optimize spacecraft performance characteristics.

The approach that was utilized to start up and requalify manufacture of the thermoelectric unicouple devices for the Cassini RTG (Radioisotope Thermoelectric Generator) program are described in this paper. Key elements involved in this effort were: engineering review of specifications; training of operators; manufacturing product verification runs; and management review of results. Appropriately, issues involved in activating a fabrication process that has been idle for nearly a decade, such as upgrading equipment, adhering to updated environmental, health, and safety requirements, or approving new vendors, are also addressed. The cumulative results of the startup activities have verified that a production line for this type of device can be reopened successfully.

System level design studies of space applications ranging in power from 77 kWt to 200 MWt have indicated no practical limit to the thermal power that can be reliably generated by a space reactor system based on the technologies being developed in the SP-100 program. These technologies include uranium nitride fuel, PWC-11/rhenium bonded fuel cladding, PWC-11 structural material for the lithium coolant boundary, electromagnetic coolant pumps, safety and reactivity control drive mechanisms, sensors, shielding materials, etc. at operating temperatures up to 1400K. The physical arrangements and characteristics of the nuclear reactor materials are described. The physical size of components and the arrangement of components change, but the basic technologies required are generally the same, irrespective of the total power output.

To facilitate the development of the Space Reactor Power System (SRPS) controller, a rapid prototyping and multi-phased development methodology is being utilized. The rapid prototyping environment used in the development models both the controller and the system being controlled. Since the validation of the SRPS control strategies is a long lead activity to ensure the required safety and control features, the SRPS controller development is carried out in phases, starting with normal modes of operation and followed by transient and off-normal modes. In every phase, the rapid prototyping of the control strategies is used (1) to establish well-defined controller requirements, (2) to perform fast identification of changes and refinement of the strategies, and (3) to conduct in-phase correction and optimization of the strategy and component development.

This paper describes how the SP-100 Space Reactor Power System (SRPS) can be tailored to meet the specific requirements for a lunar surface power system to meet the needs of the consolidation and utilization phases outlined in the 90-day NASA SEI study report. This same basic power system can also be configured to obtain the low specific masses needed to enable robotic interplanetary science missions employing Nuclear Electric Propulsion (NEP). In both cases it is shown that the SP-100 SRPS can meet the specific requirements. For interplanetary NEP missions, performance upgrades currently being developed in the area of light weight radiators and improved thermoelectric material are assumed to be technology ready in the year 2000 time frame. For lunar applications, some system rearrangement and enclosure of critical components are necessary modifications to the present baseline design.

Researchers now have the means to evolve complex manned and unmanned space missions using all of their complex support systems in a fully adaptive visual environment. The expected interactive nature of space missions requires powerful, flexible and comprehensive simulation hardware and software to develop and verify concepts, systems, and procedures. Correlation of visual, sensor, and radar imagery is essential due to new sensor blending and fusion techniques that characterize complex systems and missions. Only through total visual, non-visual and mission environment simulation, combined with analytical tools, can reliable systems and missions be developed. The same can be said of the simulation-based training programs that must be developed for ground and flight mission crews. If maximum situational awareness cannot be trained through simulation, it may be too risky, too expensive or even too late to acquire during a mission.

This paper discusses the technology, components and systems incorporated in the design of the LM1600 I/CR marine gas turbine propulsion system as well as describing some of the novel and imaginative ways that the highly acclaimed F404 fighter aircraft engine has been modified and adapted to provide the nucleus for this sophisticated marine propulsion system. Specifically, the modifications to the compressors, the high and low pressure turbines and the power turbine design characteristics are described. The proven materials technology from the highly successful LM2500 marine gas turbine has been applied to this engine as well.

EXPERIMENTAL RESULTS are presented for the effects of water in #2 diesel fuel emulsion on engine performance and combustion for a two cylinder laboratory engine of GE-7FDL series diesel engine parameters. Smoke, NOx, and CO emissions were decreased as the water amount in fuel was increased. At the maximum tested amount of about 30% water, smoke reading was reduced by half (Bosch number) and NOx reduced by 50% at full load. Fuel consumption can be lowered somewhat by adding water also. The potential of fuel savings is about 1-2%. it is more at the lower intake pressure notch 5 load than notch 8 load with higher intake pressure. Both emissions reduction and fuel saving were realized at the expense of increased engine running roughness.

All of the properties of the materials used in the design, analysis, and manufacture of jet engines are listed in the seven-volume Material Properties Handbook. Keeping these volumes of curves up-to-date has been a constant challenge, but recently work began to replace the old system of printed volumes with a computerized record that can be accessed from virtually anywhere. This paper is a status report on the project.

An organic Rankine Bottoming cycle added to Diesel engines used for long-haul trucks has the potential of improving their peak fuel economy by up to 15% over a typical duty cycle. General Electric has developed a multi-vane rotary expander which has a measured isentropic brake efficiency of 80+% over a wide range of speed and power levels with organic working fluids. High cycle efficiency for design and off-design conditions is achieved with the multi-vane expander. The potential advantages of the multi-vane expander for the Diesel engine bottoming cycle include the elimination of a high speed gear box and the potential for over 80% isentropic engine efficiency. The multi-vane expander is a ruggedly built component running at Diesel engine speed. This paper describes the design and evaluation of a nominal 40 HP multi-vane expander for this application.

Alternative engine concepts to the advanced high bypass turbofan which have promise of reducing energy consumption including regenerative cycles and other engines with heat exchangers, unconventional engine arrangements such as geared fan engines, and high disc loading turboprops. After initial screening, several concepts were selected for a systematic evaluation of the merits of each relative to a high bypass turbofan based on advanced technology consistent with the mid 1980's time period. Both mission fuel and direct operating cost for typical long range transport missions were considered in the evaluation.

Standard laboratory immersion tests show silicone rubber to be stable in ASTM #1, #3 oils and in unused engine lube oils. However, new test data have shown that silicone rubber will degrade when exposed to engine lube oil which has functioned in lubricating a diesel engine for many hours of service. Special silicone rubber compounds have greatly improved the resistance to degradation as shown by laboratory tests and diesel engine tests of cylinder liner seals. These silicone rubber materials should also better the seal performance in other engine applications requiring low temperature flex, high temperature and petroleum base oil resistance.

The principal design features of the NASA QCSEE UnderThe-Wing and Over-The-Wing powered lift propulsion systems are given. In the UTW engine, these include noise reduction features, a variable pitch low pressure ratio fan, a fan drive reduction gear, an advanced core and low pressure turbine with a low pollution combustor, a digital control, and advanced composite construction for the inlet, fan frame, fan exhaust duct, and variable area fan exhaust nozzle. The OTW engine is similar but has higher fan pressure and a fixed pitch fan. Both engines are scheduled to be fabricated and tested starting in 1976.

Previous studies had demonstrated the economic and technical feasibility of producing high-quality forgings for aircraft turbine engine parts from hot-isostatically pressed (HIP) Rene 95 powder billets. The present program was aimed at developing a production practice for making HIP + forged turbine discs. The major goal was improved product fabricability and reliability with minimum cost. The program was conducted using argon atomized Rene 95 powder. Experimental studies were conducted to evaluate the effect of powder characteristics, HIP parameters, preform design, and forging conditions on forgeability, microstructure, and mechanical properties. The results of these studies were incorporated into a pilot production run in which 10 disc forgings were made and evaluated. The selected process involved the consolidation of -60 mesh powder to full density by hot-isostatic pressing at a temperature above the γ' solvus temperature.

The advantages of infinitely variable ratio steering and propulsion for track laying vehicles are well known. Studies and demonstrator programs in the past decade have indicated that the hydromechanical transmission has the most promise of providing infinitely variable ratio for military vehicles. In 1966 the Army launched a program to develop the hydromechanical transmission to “production ready” status. This paper describes that program, the transmission selected, and some of the problems encountered in the transition from the demonstrator stage to one of readiness for military application.

The effects of transmission selection on the performance and fuel economy of a gas turbine powered automobile are analyzed. Both single-shaft and two-shaft turbines are considered. Examples are given of fuel economy for an urban cycle, and performance of these engines with an infinitely variable transmission and with a power shift automatic transmission. The primary conclusions are that the infinitely variable transmission is necessary for a single-shaft engine and highly desirable for a two-shaft engine, and the use of an infinitely variable transmission with the single-shaft turbine eliminates any need for the wider output speed range of a two-shaft engine.

The General Electric Company has recently been in the process of developing two new turbofan aircraft engines-the TF34 and the F101. The TF34 has been developed for the U.S. Navy's S-3A antisubmarine warfare aircraft and has been selected by Fairchild-Hiller for the U.S. Air Force A-10A; the F101 is being developed for the U.S. Air Force B-1 strategic bomber. Each of the new aircraft programs has the common requirement for subsonic endurance. The S-3A and A-10A requirements include subsonic operation only while the B-1 includes supersonic capability as well as subsonic. This basic mission-mix difference combined with major differences in engine/air vehicle installation features and different levels of technology applied due to the relative chronology in the respective development programs leads to contrasts in the design features of the major components of the engines.