Search Results

Reactivity Controlled Compression Ignition (RCCI) combines very high thermal efficiencies with ultra-low engine out NOx and PM emissions. Moreover, it enables the use of a wide range of fuels. As this pre-mixed combustion concept relies on controlled auto-ignition, closed-loop combustion control is essential to guarantee safe and stable operation under varying operating conditions. This work presents a coordinated air-fuel path controller for RCCI operation in a multi-cylinder heavy-duty engine. This is an essential step towards real-world application. Up to now, transient RCCI studies focused on individual cylinder control of the fuel path only. A systematic, model-based approach is followed to design a multivariable RCCI controller. Using the Frequency Response Function (FRF) method, linear models are identified for the air path and for the combustion process in the individual cylinders.

The Reactivity Controlled Compression Ignition concept for dual-fuel engines has multiple challenges of which some can be overcome using Variable Valve Actuation approaches. For various fuel combinations, the engine research community has shown that running dual-fuel engines in RCCI mode, improves thermal efficiency and results in ultra-low engine-out nitrous oxides and soot. However, stable RCCI combustion is limited to a certain load range, depending on available hardware. At low loads, the combustion efficiency can drop significantly, whereas at high loads, the maximum in-cylinder pressure can easily exceed the engine design limit. In this paper, three VVA measures to increase load range, improve combustion efficiency, and perform thermal management are presented. Simulation results are used to demonstrate the potential of these VVA measures for a heavy-duty engine running on natural gas and diesel.

The operation of a dual fuel combustion engine using combustion mode-switching offers the benefit of higher thermal efficiency compared to single-mode operation. For various fuel combinations, the engine research community has shown that running dual fuel engines in Reactivity Controlled Compression Ignition (RCCI) mode, is a feasible way to further improve thermal efficiency compared to Conventional Dual Fuel (CDF) operation of the same engine. In RCCI combustion, also ultra-low engine-out NOx and soot emissions have been reported. Depending on available hardware, however, stable RCCI combustion is limited to a certain load range and operating conditions. Therefore, mode-switching is a promising way to implement RCCI in practice on short term. In this paper, a model-based development approach for a dual fuel mode-switching controller is presented. Simulation results demonstrate the potential of this controller for a heavy-duty engine running on natural gas and diesel.

SCR on Filter (SCRoF) is an efficient and compact NOX and PM reduction technology already used in series production for light-duty applications. The technology is now finding its way into the medium duty and heavy duty market. One of the key challenges for successful application is the robustness to real world variations. The solution to this challenge can be found by using model-based control algorithms, utilizing state estimation by physics-based catalyst models. This paper focuses on the development, validation and real time implementation of a physics-based control oriented SCRoF model. An overview of the developed model will be presented, together with a brief description of the model parameter identification and validation process using engine test bench measurement data. The model parameters are identified following a streamlined approach, focusing on decoupling the effects of deNOx and soot phenomena.

For natural gas (NG)-diesel RCCI, a multi-zonal, detailed chemistry modeling approach is presented. This dual fuel combustion process requires further understanding of the ignition and combustion processes to maximize thermal efficiency and minimize (partially) unburned fuel emissions. The introduction of two fuels with different physical and chemical properties makes the combustion process complicated and challenging to model. In this study, a multi-zone approach is applied to NG-diesel RCCI combustion in a heavy-duty engine. Auto-ignition chemistry is believed to be the key process in RCCI. Starting from a multi-zone model that can describe auto-ignition dominated processes, such as HCCI and PCCI, this model is adapted by including reaction mechanisms for natural gas and NOx and by improving the in-cylinder pressure prediction. The model is validated using NG-diesel RCCI measurements that are performed on a 6 cylinder heavy-duty engine.

Premixed combustion concepts like PCCI and RCCI have attracted much attention, since these concepts offer possibilities to reduce engine out emissions to a low level, while still achieving good efficiency. Most RCCI studies use a combination of a high-cetane fuel like diesel, and gasoline as low-cetane fuel. Limited results have been published using natural gas as low-cetane fuel; especially full scale engine results. This study presents results from an experimental study of diesel-CNG RCCI operation on a 6 cylinder, 8 l heavy duty engine with cooled EGR. This standard Tier4f diesel engine was equipped with a gas injection system, which used single point injection and mixed the gaseous fuel with air upstream of the intake manifold. For this engine configuration, RCCI operating limits have been explored. In the 1200-1800 rpm range, RCCI operation with Euro-VI engine out NOx and soot emissions was achieved between 2 and 9 bar BMEP without EGR.

A promising SCR-only solution is presented to meet post-2010 NOx emission targets for heavy duty applications. The proposed concept is based on an engine from a EURO IV SCR application, which is considered optimal with respect to fuel economy and costs. The addition of advanced SCR after treatment comprising a standard and a close-coupled SCR catalyst offers a feasible emission solution, especially suited for EURO VI. In this paper, results of a simulation study are presented. This study concentrates on optimizing SCR deNOx performance. Simulation results of cold start FTP and WHTC test cycles are presented to demonstrate the potential of the close-coupled SCR concept. Comparison with measured engine out emissions of an EGR engine shows that a close-coupled SCR catalyst potentially has NOx reduction performance as good as EGR. Practical issues regarding the use of an SCR catalyst in close-coupled position will be addressed, as well as engine and exhaust layout.

To meet 2010 emission targets, optimal SCR system performance is required. In addition, attention has to be paid to in-use compliance requirements. Closed-loop control seems an attractive option to meet the formulated goals. This study deals with the potential and limitations of closed-loop SCR control. High NOx conversion in combination with acceptable NH3 slip can be realized with an open-loop control strategy. However, closed-loop control is needed to make the SCR system robust for urea dosage inaccuracy, catalyst ageing and NOx engine-out variations. Then, the system meets conformity of production and in-use compliance norms. To demonstrate the potential of closed-loop SCR control, a NOx sensor based control strategy with cross-sensitivity compensation is compared with an adaptive surface coverage/NH3 slip control strategy and an open-loop strategy. The adaptive surface coverage/NH3 slip control strategy shows best performance over simulated ESC and ETC cycles.

In the past decade, SCR deNOx technology with urea injection has grown to maturity. European OEMs will apply SCR deNOx to meet future heavy-duty emissions legislation starting with EURO-4 (2005/2006). Numerous research programs in Europe and the US have shown a variety of system layouts and control strategies. The main differences are formed by: the engine-out NOx calibration the application of an NO to NO2 catalyst open-loop or closed-loop urea dosage control. This paper gives an overview of possible SCR system configurations that are required for different stages of future emission legislation. Engine-out NOx emission is strongly influenced by ambient conditions. Projections in this study show that a combination of cold climate and a wintergrade fuel is the most severe: it may lead to 30% lower engine-out NOx emission with respect to laboratory conditions.

In a NOx adsorber programme the feasibility for applying this technology to heavy duty diesel engines was investigated. After modelling and simulations for realising best λ < 1 engine conditions a platform was build which was used to obtain good NOx adsorber regeneration settings in a number of steady state key points without violating pre-defined limits. With these results the NOx adsorber was evaluated and tested. Besides establishing NOx conversions and BSFC penalties the programme also looked at the adsorber capabilities of dealing with sulphur poisoning and how well the adsorber could be de-sulphurised. This programme showed clearly the stronger and weaker points in the NOx adsorber technology for heavy duty application. From NOx conversion - BSFC penalty trade off curves it became clear that at lower loads high conversions (> 90%) with small fuel penalties (< 2.5%) were possible. However at high load the conversions were reduced (< 70%) and the fuel penalties increased (> 6%).

The application of SCR deNOx aftertreatment was studied on two about 12 liter class heavy-duty diesel engines within a consortium project. Basically, the system consists of a dosage system for aqueous urea injection and a vanadia based SCR catalyst, without an upstream or downstream oxidation catalyst. The urea injection system for a DAF and a Renault V.I. (Véhicules Industriels) diesel engine was calibrated on the engine test bench taking into account dynamic effects of the catalyst. For both engine applications NOx reduction was 81% to 84% over the ESC and 72% over the ETC. CO emission increased up to 27%. PM emission is reduced by 4 to 23% and HC emission is reduced by more than 80%. These results are achieved with standard diesel fuel with about 350 ppm sulfur. The test engines and SCR deNOx systems were built into a DAF FT95 truck and a Renault V.I. Magnum truck.

This paper reports on a study of the TNO venturi EGR system and the Johnson Matthey CRT particulates trap on a DAF 355 kW engine. The results obtained indicate that this EGR-CRT combination is an effective means to achieve EURO-4 emission level, while maintaining good fuel economy. EGR strategy, injection timing and air-fuel ratio were optimised in such a way that good regeneration conditions were obtained across most of the engine operating map. Also transient EGR control is optimised to combine low NOx emission during the ETC with good driveability and good engine out particulates emission. The size of the oxidation catalyst in the CRT was investigated. It appeared that the larger oxidation catalyst showed a better regeneration performance during a low temperature duty-cycle. Negative aspects of a larger oxidation catalyst are increased costs and increased NO2 emission (because of the catalyst ability to oxidise more NO into NO2).

This paper presents a start algorithm that is able to control the air/fuel ratio (AFR) during the cranking phase and immediately hereafter, where the ordinary λ-control is not yet enabled. The control is based on the ion sense principle, which means that a current through the spark plug is measured directly after the spark has disappeared. This current is a measure for the temperature and therefore of the combustion in the cylinder. This is an excellent way to start a CNG (Compressed Natural Gas) engine with unknown gas qualities. A typical example of application is when the vehicle is almost out of fuel and is refueled at a motel stop. The small amount of old fuel that is left in the system will mix with the new fuel resulting in an unknown fuel quality. The control system shall then be able to start the engine directly or after an accommodation over night. During the last condition, the oxygen sensor is still cold and thus not able to correct for fuel quality changes.