Search Results

Hydrogen–diesel dual-fuel combustion processes were visualized using an optically accessible rapid compression and expansion machine (RCEM). A hydrogen-air mixture was introduced into the combustion chamber, and a pilot injection of diesel fuel was used as the ignition source. A small amount of diesel fuel was injected as the pilot fuel at injection pressures of 40, 80, and 120 MPa using a common rail injection system. The injection amounts of diesel fuel were varied as 3, 6, and 13 mm3. The amount of hydrogen was manipulated by varying the total excess air ratio (λtotal) at 3 and 4. The RCEM was operated at a constant speed of 900 rpm, and the in-cylinder pressure and temperature at the top dead center (TDC) were set as 5 MPa and 700 K, respectively. The combustion processes were visualized via direct photography and hydroxyl (OH*) chemiluminescence photography using a high-speed camera and an image intensifier.

In a rapid compression and expansion machine (RCEM), spray flames from a two-hole injector are injected toward a wall to achieve jet-jet interaction after spray flames impinge onto the wall. Simultaneous laser-induced incandescence (LII) and laser scattering (LS) measurements were performed to investigate the soot formation process in the jet-jet interaction zone. The results showed that high LII and LS signals were detected in the interaction region and persisted for a considerable period and that soot particle size in the interaction zone was independent of the time and injection pressure.

To understand the effect of discharge frequency and discharge energy of dielectric barrier discharges (DBD) on the flame kernel development process, the observation of the discharges and ignition trials were performed in a constant volume vessel. Results showed that the energy of DBD released during a single cycle of discharge decreases, but the power of the discharges increases with the frequency increases. The ignition probability improved and the time for the flame propagation decreased under high frequency because the power of the discharges efficiently rises the local gas temperature near the electrodes.

To clarify the relationship between the local heat release and the velocity distribution inside the diesel spray flame, simultaneous optical diagnostics of OH* chemiluminescence and particle image velocimetry (PIV) have been applied to the diesel spray flame under the elevated in-cylinder pressure and temperature conditions formed in a rapid compression expansion machine (RCEM). The cranking speed of the RCEM was 900 rpm, and the in-cylinder pressure and temperature were 8 MPa and 800 K at the start of injection, respectively. The amount of fuel was 10.2 mg. The injection pressure was 120, 90, and 60 MPa. To minimize the disturbance of luminous flame on optical diagnostics, a solvent, with comparable combustion characteristics to diesel fuel was used as fuel. The oxygen concentration was set to 15%. Results clearly show that PIV can successfully analyze the velocity distribution in diesel spray flames.

The effects of jet-jet angle on the combustion process were investigated in an optical accessible rapid compression and expansion machine (RCEM) under various injection conditions and intake oxygen concentrations. The RCEM was equipped with an asymmetric six-hole nozzle having jet-jet angles of 30° and 45°. High-speed OH* chemiluminescence imaging and direct photo imaging using the Mie scattering method captured the transient evolution of the spray flame, characterized by lift-off length and liquid length. The RCEM operated at 1200 rpm. The injection timing was -5°ATDC, and the in-cylinder pressure and temperature were 6.1 MPa and 780 K at the injection timing, respectively, which achieved a short ignition delay. The effects of injection pressure, nozzle hole diameter, and oxygen concentration were investigated.

The main objective of this study is to evaluate the characteristics of combustion that combine premixed charge compression ignition (PCCI)-based combustion with conventional mixing controlled combustion. In this type of combustion, it is supposed that the combustion duration is shortened due to the synchronization of the timing of two types of combustions. In addition, the cooling loss caused by spray impingement is expected to decrease by the reduction of the proportion of mixing controlled combustion. In this study, the effect of injection pressure, injection timing, and split injection on thermal efficiency and emissions were investigated in order to determine the appropriate injection parameters for PCCI-based combustion to realize the proposed combustion concept.

This work investigated the mechanism of oil dilution by post injection to remove accumulated particulate matter on the diesel particulate filter of diesel engines. We developed a model to simulate post injection spray under low ambient gas pressure conditions. The model can predict the quantity of fuel mass adhered on the cylinder wall. The adhered fuel enters oil sump through the piston ring and cause oil dilution. The fuel in diluted oil evaporates during normal engine operations. We focus on the mechanism of fuel evaporation from diluted oil. The effects of engine speed and oil temperature on the evaporation were investigated. The results showed that the fuel evaporation rate increases with increasing engine speed and oil temperature. Furthermore, we developed an empirical model to predict the fuel evaporation rate of diluted oil through regression analysis with measured data.

Commercial three way catalysts (TWC) are designed to eliminate HC, CO and NOx pollutants emitted from gasoline powered internal combustion engines. TWC have been optimized over many years to meet ever more stringent emission regulations. It has long been speculated that surface electrical conductivity may be a key parameter in controlling catalytic activity, however until now it has not been possible to reliably measure this physical parameter on a catalytic surface. In this study, the surface electrical conductivity of catalyst powders, such as Rh/ CeO1-x-ZrxO2, Rh/ZrO2 and Rh/Al2O3, were measured by EUPS (Extreme Ultraviolet excited Photoelectron Spectroscopy). Then the measured electrical conductivity was compared with catalyst performance from CO-NO and water gas shift reactions which are important for controlling automobile exhaust emissions from gasoline vehicles.

A series of experiments was conducted using a single-cylinder small-bore (85 mm) diesel engine to investigate the smoke-reduction effect of post injection by varying the number of injection nozzle orifices and the injection pressure. The experiments were performed under a constant injection quantity condition and under a fixed NOx emission condition. The results indicated that the smoke emission of six-hole, seven-hole, and eight-hole nozzles decreased for advanced post injection, except that the smoke emission of the 10-hole nozzle increased as the post injection was advanced from a moderately late timing around 17° ATDC. However, the smoke emission of the 10-hole nozzle with a higher injection pressure decreased for advanced post injection. These trends were explained considering the influence of the main-spray flames on post sprays based on CFD simulation results.

Numerical calculations were performed to investigate the mixture formation, ignition, and combustion processes in a diesel spray. The spray was formed by injecting n-heptane into a constant volume vessel under high-temperature and high-pressure conditions. The fuel droplets were described by a discrete droplet model (DDM). Numerical calculations for the flow and turbulent diffusion processes were performed on the basis of large eddy simulation (LES) to describe the processes of local non-homogeneous mixture formation and heat release. The oxidation processes in the mixture were calculated by Schreiber's five-step mechanism for n-heptane. Calculations were performed for sprays formed by single-stage injection and pilot/main two-stage injection. The flame structure in a diesel spray and its temporal change were discussed using a flame index proposed by Yamashita et al.

The methodology of lubricity evaluation for DME fuel was established by special modified HFRR (High-Frequency Reciprocating Rig) such as Multi-Pressure/Temperature HFRR (MPT-HFRR). The obtained results were summarized as follows: The HFRR method is adaptable with DME fuel. There is no effect of the test pressure (up to 1.8 MPa) and the test temperature (up to 100°C) of MPT-HFRR on wear scar diameter. The results with MPT-HFRR can be applied at the sliding parts of the injection needle and the fuel supply pump's plungers which are secured lubricity by the boundary lubrication mode mainly and the mixed lubrication mode partially. Using the fatty-acid-based lubricity improver in amounts of approximately 100 ppm, the lubricity of DME, which has a lack of self-lubricity, is ensured as same as the diesel fuel equivalent level. There is a big deviation of measured wear scar diameter when the LI concentration is not enough.

Numerical calculations based on large eddy simulation were performed in order to investigate mixture formation, ignition, and combustion processes in a diesel spray formed by fuel injection into a constant-volume vessel under high-temperature and high-pressure conditions. Fuel concentration distributions in a spray and local non-homogeneous mixture distributions were compared with experimental results to verify the accuracy of the calculations. In addition, calculations were carried out to examine the effect of injection parameters, namely, injection pressure and nozzle orifice diameter. Ignition and combustion processes were also investigated using Schreiber's model for calculating the progress of oxidation reactions.

DME as a fuel for compression ignition (diesel) engines has been actively studied for about ten years due to its characteristically low pollution and reputation as a “smokeless fuel”. During this time, the practical application is taking shape based on necessary tasks such as analysis of injection and combustion, engine performance, and development of experimental vehicles. At this moment, standardization of DME as a fuel was started under ISO in 2007. There are concerns regarding the impurities in DME regarding the mixing during production and distribution as well as their effect on additives for lubricity and odor. In this report, the effect of DME fuel impurities on performance of a DME powered diesel engine was investigated. The platform was a DME engine with common-rail fuel injection and was evaluated under partial load stable mode and Japanese transient mode (JE05) testing parameters.

The tasks to improve diesel emissions and fuel consumption must be accomplished with urgency. However, due to the trade-off relationship between NOx emissions, soot emissions and fuel consumption, clean diesel combustion should be achieved by both innovative combustion and fuel technologies. The objective of this study is to extend the clean diesel combustion operating range (Engine-out emission: NOx ≺ 0.2 g/kWh, Soot ≺ 0.02 g/kWh). In this study, performance of a single-cylinder test engine equipped with a hydraulic valve actuation system and an ultra-high pressure fuel injection system was investigated. Also evaluated, were the effects of fuel properties such as auto-ignitability, volatility and aromatic hydrocarbon components, on combustion performance. The results show that applying a high EGR (Exhaust gas recirculation) rate can significantly reduce NOx emission with an increase in soot emission.

A diesel combustion model for CFD simulation is established taking into account the auto-ignition process of a non-homogeneous mixture. In a previous paper, the authors revealed that the non-homogeneity of a fuel-air mixture has a more significant effect on the auto-ignition process with respect to, for example, ignition delay or combustion duration, as compared to the turbulent mixing rate. Based on these results, a novel diesel combustion model is proposed in the present study. The transport calculation for the local variation of the fuel-air PDF is introduced, and the chemical reaction rate is obtained based on the local non-homogeneity. Furthermore, this model incorporates RANS-based CFD simulation of the spray combustion in a constant-volume vessel under a high-temperature, high-pressure condition. The results show that the combustion process is well described for a wide range of temperature and pressure conditions.

Diesel combustion model for CFD simulation is established taking account of an auto-ignition process of non-homogeneous mixture. Authors revealed in their previous paper that the non-homogeneity of fuel-air mixture affected more on auto-ignition process such as its ignition delay or combustion duration than the turbulent mixing rate. Based on these results, novel diesel combustion model is proposed in this study. The transport calculation for local variation of fuel-air PDF is introduced and the chemical reaction rate is provided by the local non-homogeneity. Furthermore, this model is applied the RANS based CFD simulation of the spray combustion in a Diesel engine condition. The results show that the combustion process is well described for several engine operations.

Fundamental investigation is conducted on flow and the spark-ignited combustion process of a high-speed, unsteady hydrogen jet, by experimental and theoretical approaches. Jet development and flame propagation in a constant-volume vessel were visualized by means of the shadowgraph technique. The effects of ignition timing and ignition location on the combustion process were investigated. Furthermore, a numerical simulation was performed by using incompressible-flow type computational fluid dynamics with the k-ε turbulence model and the flamelet concept. The pseudo-nozzle concept is applied to the inlet condition with a large pressure gradient. The flame propagation process is described by reference to the flame area evolution model. The results show that the pressure-history in a vessel and the flame propagation process are successfully described for experimental data. Furthermore, the flame propagation process in a jet is investigated.

It has been clarified that diesel fuel properties have a great effect on the exhaust emissions and fuel consumption of a conventional diesel combustion regime. And as other diesel combustion regimes are applied in order to improve exhaust emissions and fuel consumption, it can be supposed that the fuel properties also have significant effects. The purpose of this study is to propose the optimum diesel fuel properties for a premixed compression ignition (PCI) combustion regime. In this paper, the effect of the auto-ignitability of diesel fuels on exhaust emissions and fuel consumption was evaluated using a heavy-duty single-cylinder test engine. In all experiments, fuels were injected using an electronically controlled, common-rail diesel fuel injector, and most experiments were conducted under high EGR conditions in order to reduce NOx emissions.

In an attempt to grab potential issues with a hydrogen direct injection lean burn engine to have similar power output to a gasoline-fuelled engine, emission characteristics of a hydrogen engine was investigated. It is demonstrated that low NOx emission can be achievable without any catalytic converter. Two major issues, however, have been recognized, that is, combustion instability at low load conditions and too low temperature of exhaust gas to get enough boosting pressure. Hydrogen concentration heterogeneous of the mixture was focused in the CFD and visualization study. Hydrogen jet design of an injector could contribute to improvement of mixing.

Auto-ignition of a non-homogeneous mixture was fundamentally investigated by means of a numerical calculation based on chemical kinetics and the stochastic approach. In the present study, the auto-ignition process of n-heptane is calculated by means of a reduced mechanism developed by Seiser et. al. The non-uniform states of turbulent mixing are statistically described using probability density functions and the stochastic method, which was originally developed from Curl's model. The results show that the starting points of the low-temperature oxidation and ignition delay period are hardly affected by the equivalence-ratio variation; however, combustion duration increases with increasing variance of equivalence ratio. Furthermore, combustion duration is mainly affected by the non-homogeneity at the ignition and not very much affected by the mixing rate.