Search Results

This technical paper reports the development of an automatic defect detector utilizing deep learning for “polished skins”. Materials with a “polished skin” are used in the fabrication of the external plates of commercial airplanes. The polished skin is obtained by polishing the surface of an aluminum clad material, and they are visually inspected, which places a significant burden on inspectors to find minute defects on relatively large pieces of material. Automated inspection of these skins is made more difficult because the material has a mirror finished surface. Defects are broadly classified into three categories: dents, bumps, and discolorations. Therefore, a defect detector must be able to detect these types of defects and measure the defects’ surface profile. This technical paper presents details related to the design and manufacture of an inexpensive automated defect detector that demonstrates a sufficiently high level of performance.

The authors developed a gasoline engine that combined direct injection and port fuel injection in order to improve fuel economy for motorcycles. Compared to passenger car engines, motorcycle engines generally have smaller displacement and operate at higher engine speed, so the bore and stroke are generally smaller than those of passenger cars. Therefore, the direct injection spray characteristics optimized for small bore and stroke were selected to reduce fuel adhesion to various parts of the combustion chamber wall. In addition, this engine employed the high tumble intake port that can both strengthen turbulence intensity and suppress the decrease in volumetric efficiency to a lower level. Also, stratification of air-fuel mixture and split injection were employed for reducing catalyst warm-up time and soot. The results showed that excellent fuel economy was achieved without sacrificing engine output performance while meeting emissions regulations.

Electroimpact and Kawasaki Heavy Industries (KHI) have produced a new riveting process for the forming of Briles type rivets in Boeing 777 and 777X fuselage assemblies. The Briles rivet is typically used for fuselage assembly and is unique in that it has a self-sealing head. Unlike conventional headed rivets such as the NAS1079, this fastener does not require aircraft sealant under the head to be fluid tight. This unique fastener makes for a difficult fastening process due to the fact that interference must be maintained between the hole and fastener shank, as well as along the sides of the fastener head. Common issues with the formed fasteners include gapping under the fastener head and along the shank of the fastener. Electroimpact has employed a host of different technologies to combat these issues with Briles fastening. First, Electroimpact’s patented “Air Gap” system allows the machine to confirm that the head of the rivet is fully seated in the countersink prior to forming.

The traction-drive integrated drive generator (T-IDG®) has been developed since 1999 to replace current hydrostatic transmission drive generators mounted on Japanese military aircraft. The T-IDG® consists of a generator and a half-toroidal traction-drive continuously variable transmission (CVT), which maintains a constant output speed of 24000 rpm, that is, a 400 Hz AC power supply. To cope with recent trends of more electric aircraft (MEA) and the need for weight reduction, a high-speed traction-drive CVT is advantageous over other transmissions. The torque on the half-toroidal variator is transmitted through multiple power rollers. The equal load sharing among power rollers is typically controlled by a mechanical hydraulic feedback system, whose stability is one of the main issues for the high-speed traction-drive CVT. Previous studies have shown that insufficient damping and stiffness of the mechanical hydraulic feedback system cause self-induced vibration.

In this study on the motorcycle engine, we investigated the geometry of the newly developed intake port with an objective of improving the fuel consumption and the torque in practical range. Herein we present the results obtained. We believe that an effective measure for achieving the stated objective is to improve the combustion speed and combustion stability. To realize that, it is necessary to increase the turbulence during combustion and improve the homogeneity of air-fuel mixture. To investigate the feasible shape of the port, the CFD simulation (including fuel spray analysis) was performed and a geometry that improved the turbulent kinetic energy and mixture homogeneity at the time of ignition was selected. For confirming the combustion improvement effect achieved by tumble strengthening, an engine test was conducted with the same amount of intake air as that used in.

The power train system for Utility Vehicles (UVs) or All-Terrain Vehicles (ATVs) mainly consists of a rubber V-belt CVT. The adjustment of the CVT specification requires many steps to realize the shifting operations of the CVT so as to satisfy the acceleration feeling of the driver. In this paper, we report on the simulation technology that predicts the transient behavior during an acceleration of the vehicle equipped with a belt tension clutching CVT, which has both functions of the shift operation and the clutch action. By using the developed simulation technique, it has become possible to adjust the CVT specifications efficiently.

Generally, it is thought that control is simpler than an Internal Combustion Engine (ICE)-Motorcycle(MC) as for the Electric Vehicle(EV) type MC. However, there is few characteristic to the ICE-MC to the EV-MC and it cannot get good performance without control for EV-MC. We study the methodology for design and evaluation an EV-MC. In this approach, we developed the prototype EV-MC having manual transmission. In our study, we think that EV-MC having manual transmission is feature in comparison with other general EV-MC. From this feature, we had to develop the function control in addition to standard EV-MC function control. This paper provides a function control for EV-MC having manual transmission. In this paper, we arrange the problem points of EV-MC which put electric propulsion motor and manual transmission together at first. And report the result that studied a method to solve the problem points.

In the modern aircraft manufacturing, the cost reduction, the manufacturing time reduction, and the weight saving of aircraft are strongly demanded. The Refill Friction Spot Joining [1,2](FSJ, in other words FSSW, Friction Stir Spot Welding), which is one of innovative solid-state joining methodologies based on the Friction Stir Welding[3], is a promising technology that can replace rivets and fasteners. This technology is expected to offer cost reduction and weight saving for the aircraft manufacturing. In this study, to make stronger and reliable joints, the shoulder-plunging process of Refill FSJ was employed. The weldability of the Alodine or Chromic Acid Anodize coated materials along with a faying-surface sealant was investigated. The joint properties, such as tensile shear strengths and corrosion resistance, were evaluated.

In the expansion of composite material application, it is one of the most important subjects in assembly of aircraft structure how drilling of composite/metal stack should be processed in an efficient way. This paper will show the result of development of a drill bit for CFRP/Aluminum-alloy stack by Kawasaki Heavy Industries (KHI) and Sumitomo Electric Hardmetal (SEH). In order to improve workability and economic performance, the drill bit which enables drilling CFRP/Al-alloy stack: at 1 shot; from both directions; without air blow and coolant (just usual vacuuming); was required. A best mix drill bit which has smooth multi angles edge and pointed finishing edge was produced as a result of some trials. Developed drill bit achieved required performance and contributed to large cost reduction, labor hour saving, production speed increase and work environment improvement.

In this study, the technology that can predict fatigue life for motorcycle exhaust systems is developed. To predict the fatigue life, analyzing the engine vibration, modeling the vibration characteristics of exhaust systems and evaluating the fatigue damage of welded joints are considered essential. This paper shows an integrated numerical simulation and evaluation method. Furthermore, it is also shown with the result of a component vibration test of the muffler assembly to validate the technology. The results indicate a good correlation between the numerical simulation and the test.

The purpose of this paper is to propose a control method to reduce acceleration shock in motorcycles. Reducing the acceleration shock is very important in improving driveability of motorcycles. Motorcycles equipped with manual transmission have some backlashes in the transmission, with large backlash especially in dog clutch portions. We have figured out that one of the main causes of the acceleration shock is the collision of the dogs at high relative angular velocity during acceleration. Also, our data analysis has revealed that there is a correlation between a peak value of the longitudinal body acceleration and the relative angular velocity at the moment of the dog collision. A simulation was undertaken to verify this phenomenon, and its results have made it clear that we need to decrease the relative angular velocity at the moment of the dog collision so as to reduce the acceleration shock.

In line with the increase in the output of motorcycle engines, there has been an increase in incidents of the seizure between shift fork and gear because of the increased thrust force. We designed a test method that uses actual shift forks to simulate actual sliding conditions, then used that test method to evaluate the feature of the shift fork sliding and the different shift fork surface treatments. The shift fork slid against the gear not as surface contact but as tilted contact. We selected the candidates from the view that the surface treatment of the shift fork contact surface to give it higher seizure resistance when in tilted contact is required. We evaluated chromium nitride thin film, diamond-like carbon thin film, molybdenum sprayed coating, and sulphonitriding, and molybdenum sprayed coating exhibited the highest seizure resistance. The conformability plays a significant role in the sliding between the shift fork and the gear.

In order to improve the fuel efficiency and the operating performance of motorcycles, there is a need to reduce their weight. Magnesium, which is the lightest of the various metals currently being used and has a high specific strength, has the potential to satisfy that need. We conducted a study to clarify the weldability and strength characteristics of, and the most suitable surface treatment for, extruded magnesium alloys and rolled magnesium alloys. Based on the stress analysis by the finite element method, we designed a magnesium swing arm and produced the prototype swing arm by pressing hot rolled AZ31 magnesium alloy plates and welding them. The prototype is about 10% lighter and has higher torsional rigidity than a conventional aluminum swing arm.

In response to design requirements for lower weight and higher output, the motorcycle engine cylinder block has evolved from a cast cylinder block to an aluminum alloy cylinder block whose bore walls are surface-treated for wear-resistance. Hard-chromium plating, nickel-compound plating, and the like are in wide use as the wear-resistance surface treatment method, but spray technology has recently been attracting attention because of less impact on the environment, superior initial running-in performance and good oil retention. We have been applying a unique spraying method called wire explosion spraying to those models with a special need for wear-resistance surface. In this report we describe our wire explosion spray technology. With the aim of improving the bond strength of the sprayed coat, we studied the effects of the collided particles' form on bond strength in the wire explosion spraying conditions.

This paper describes the predicted results of acoustic transmission loss (T.L.) for a motorcycle muffler. First, the T.L. of a prototype muffler with one expansion chamber was obtained by measuring sound levels at the inlet and outlet ports of the muffler by speaker test. T.L. was then calculated by using a three-dimensional Finite-Element Method (FEM) for acoustic fields in the muffler. There was good coincidence between the calculated T.L. and experimentally observed data. Second, T.L. of the prototype muffler while attached to a motorcycle engine was measured. On this step, however, a similarly calculated T.L. using FEM to consider the effect of exhaust gas temperature in the muffler showed differences from the measured one. It was estimated that muffler body vibration sounds may affect the result. A dynamic analysis of the structure was carried out using FEM to obtain the eigen modes of the muffler body.

A Temperature and Humidity Control (THC) assembly an essential system in order to provide comfortable environment for crew members in Japanese Experiment Module (JEM). Development of an engineering model (EM) and a proto model (PM) of JEM THC assembly started from March 1991 and completed on March 1995 successfully. In this development phase, it is called JEM EM phase, qualification test of THC was conducted to verify the THC design. This paper presents JEM THC design and an outline of the assembly model development.

In the closed environments, removal of trace contaminants generated from persons, animals, and plants is important function to keep the environment below the allowable level. We conducted the fundamental tests in order to confirm design of TCCA (Trace Contaminants Control Assembly) for Closed Ecology Experiment Facilities (CEEF), and obtained the following results; 1) The palladium-on-alumina catalyst is suitable for CO, CH4, C2H4 conversion at temperature lower than 400°C. 2) The alkali impregnated AC (activated charcoal) is effective for NO2, SO2 removal and prevents catalyst poisoning from SO2. 3) The active-desorbing conducted by hot air blow-throw an AC is effective for C2H5OH, CH2Cl2 desorbing. We discuss the fundamental test and design conditions for TCCA.

In the closed environments such as manned space station, it is necessary to remove contaminant gas to keep a suitable environment. Removal of gaseous contaminants generated from crew, animals, and plants is important function to keep the environment below the allowable level in the Closed Ecology Experiment Facilities (abbreviated as CEEF). CEEF consist of three modules for habitat, animal and plant, the supporting facilities for each module and a plant cultivation facility. CEEF are scheduled to be constructed from 1994 in Aomori Prefecture, northern part of Japan. For designing Trace Contaminant Control Assembly (TCCA) for CEEF, the following six (6) trace contaminants have been selected as major contaminant gas in CEEF; Ammonia (NH3) Methane (CH4) Ethylene (C2H4) Carbon Monoxide (CO) Nitrogen Dioxide (NO2) Sulfur Dioxide (SO2) Ethylene is well-known as an aggressive contaminant to plant growth and maturity.