Search Results

The use of hydrogen in internal combustion engines is an effective approach to significantly support the reduction of CO2 emissions from the transportation sector using technically affordable solutions. The use of direct injection is the most promising approach to fully exploit hydrogen potential as a clean fuel, while preserving targets in terms of power density and emissions. In this frame, the development of an effective combustion system largely relies on the hydrogen-air mixture formation process, so to adequately control the charge stratification to mitigate pre-ignitions and knock and to minimize NOx formation. Hence, improving capabilities of designing a correct gas jet-air interaction is of paramount importance. In this paper the analysis of the evolution of a high-pressure gas jet produced by a single-hole prototype injector operated with different pressure ratios is presented.

Emission legislation for light and heavy duty vehicles is requiring a drastic reduction of exhaust pollutants from internal combustion engines (ICE). Achieving a quick heating-up of the catalyst is of paramount importance to cut down cold start emissions and meet current and new regulation requirements. This paper describes the development and the basic characteristics of a novel burner for diesel engines exhaust systems designed for being activated immediately at engine cold start or during vehicle cruise. The burner is comprised of a swirled fuel dosing system, an air system, and an ignition device. The main design characteristics are presented, with a detailed description of the atomization, air-fuel interaction and mixture formation processes. An atomizer prototype has been extensively analyzed and tested in various conditions, to characterize the resulting fuel spray under cold-start and ambient operating conditions.

The interest towards hydrogen fueling in internal combustion engines (ICEs) is rapidly growing, due to its potential impact on the reduction of the carbon footprint of the road transportation sector in a short-term scenario. While the conversion of the existing fleet to a battery-electric counterpart is highly debated in terms of both technical feasibility and life-cycle-based environmental impact, automotive researchers and technicians are exploring other solutions to reduce, if not to nullify, the carbon footprint of the existing ICE fleet. Indeed, ICE conversion to “green” fuels is seen as a promising short-term solution which does not require massive changes in powertrain production and end-of-life waste management. To better evaluate potentials and challenges of hydrogen fueling, a clear understanding of fuel injection and mixture formation prior to combustion is mandatory.

Ducted Fuel Injection (DFI) is a new technology recently developed with the aim of reducing soot emission formation in diesel compression ignition engines. DFI concept consists of the injection of fuel spray through a small duct located downstream of the injector nozzle leaving a certain gap, the so-called Stand-off distance. Currently, CFD modelers have investigated its performance using classical spray modeling techniques such as the Discrete Drops Method (DDM). However, as discussed in the literature, this type of technique is inappropriate when applied to dense jets as those occurring in diesel sprays, especially in the near-nozzle region (where the duct is placed). Therefore, considering a more appropriate modeling technique for such a problem is mandatory. In this research work, an Eulerian single-fluid diffuse-interface model called Σ-Y and implemented in the OpenFOAM framework is utilized for the simulation of non-reacting conditions.

Close-coupled aftertreatment systems (ATS) for automotive Diesel engines composed of DOC and SCR offer a significant potential in terms of pollutant emission control capability even with the introduction of more aggressive driving cycles and rigorous limits for type-approval tests. This is particularly important for incoming certification standards where the forecast is showing a trade-off towards ultra-low NOx emissions values. As the SCR system NOx conversion capability largely relies on both the UWS mixing device and on NOx sensors used to detect the actual NH3 slip and residual NOx concentration, developing numerical simulation tools for the analysis of the actual flow pattern and species concentration over peculiar sections of the exhaust system is crucial to support the ATS development process.

In the current automotive scenario, particulate filter technology is mandatory in order to attain emission limits in terms of particulate matter for diesel engines. Despite the fact that the Diesel Particulate Filter (DPF) is often considered a mature technology, significant issues can result from the use of the engine fuel injectors to introduce into the exhaust pipe the fuel needed to ignite the particulate matter accumulated in the filter during its regeneration. The most important issue is lubricant oil dilution with fuel as a consequence of significant spray impact on the cylinder liner. As an alternative, the fuel required to start DPF regeneration can be introduced in the exhaust pipe by an auxiliary low-pressure injector spraying in the hot exhaust gas stream.

The internal combustion engine technological development is today driven by the pollutants and carbon dioxide (CO2) emission reduction targets imposed by law. The request of lowering CO2 emission reflected in a push towards the improvement of engine efficiency, without sacrificing performances and drivability. The latest generations of Diesel engines for passenger cars are characterized by increasing injection pressure levels (250 MPa for the current production). Enhancing the injection pressure has the drawback of increasing the energy needed to pressurize the fuel and thus the high-pressure fuel pump energy request. A small but not negligible quantity of fuel has to be burned in order to provide this energy, generating a contribution in CO2 emission. In this frame, the injector back-flow represents a significant energy loss for the fuel injection system and for the whole engine.

In recent years, the GDI (Gasoline Direct Injection) technology has significantly spread over the automotive market under the continuous push toward the adoption of combustion systems featuring high thermodynamic conversion efficiency and moderate pollutant emissions. Following this path, the injection pressure level has been progressively increased from the initial 5-15 MPa level nowadays approaching 35 MPa. The main reason behind the progressive injection pressure increase in GDI engines is the improved spray atomization, ensuring a better combustion process control and lower soot emissions. On the other hand, increasing injection pressure implies more power absorbed by the pumping system and hence a penalty in terms of overall efficiency. Therefore, the right trade-off has to be found between soot formation tendency reduction thanks to improved atomization and the energetic cost of a high pressure fuel injection system.

The present paper describes the effect of thermal conditions on the hydraulic behavior of Diesel common rail injectors, with a particular focus on low temperatures for fuel and injector body. The actual injection system thermal state can significantly influence both the injected quantity and the injection shape, requiring proper amendments to the base engine calibration in order to preserve the combustion efficiency and pollutant emissions levels. In particular, the introduction of the RDE (Real Driving Emission) test cycle widens the effective ambient temperature range for the homologation cycle, this way stressing the importance of the thermal effects analysis. An experimental test bench was developed in order to characterize the injector in an engine-like configuration, i.e. fuel pump, piping, common rail, pressure control system and injectors.

Nowadays, injection rate shaping and multi-pilot events can help to improve fuel efficiency, combustion noise and pollutant emissions in diesel engine, providing high flexibility in the shape of the injection that allows combustion process control. Different strategies can be used in order to obtain the required flexibility in the rate, such as very close pilot injections with almost zero Dwell Time or boot shaped injections with optional pilot injections. Modern Common-Rail Fuel Injection Systems (FIS) should be able to provide these innovative patterns to control the combustion phases intensity for optimal tradeoff between fuel consumption and emission levels.

In order to optimize gasoline direct injection combustion systems, a very accurate control of the fuel flow rate from the injector must be attained, along with appropriate spray characteristics in terms of drop sizing and jets global penetration/diffusion in the combustion chamber. Injection rate measurement is therefore one of the crucial tasks to be accomplished in order both to develop direct injection systems and to properly match them with a given combustion system. Noticeably, the hydraulic characteristics of GDI injectors should be determined according to a non-intrusive measuring approach. Unfortunately, the operation of all conventional injection analyzers requires the injection in a volume filled with liquid and the application of a significant counter-pressure downstream of the injector. This feature prevents any operation with low pressure injection systems such as PFIs.

In the present paper, a new methodology for the estimation of the mass delivered by a single hole of a GDI injector is presented and discussed. The GDI injector used for the activity featured a five-hole nozzle characterized by three holes with the same diameter and two holes with a larger diameter. The different holes size guarantees a significant difference in terms of mass flow. This new methodology is based on global momentum flux measurement of each single plume and on its combination with the global mass measurement made with the gravimetric principle. The momentum flux is measured by means of a dedicated test bench that detects the impact force of the single spray plume at different distances. The sensing device is moved in different positions and, in each point, the force trace averaged over several injection events is acquired. The global mass delivered by the injector is measured by collecting and weighing the fuel flown during a defined number of consecutive injections.

The selection and tuning of the Fuel Injection System (FIS) are among the most critical tasks for the automotive diesel engine design engineers. In fact, the injection strongly affects the combustion phenomena through which controlling a wide range of related issues such as pollutant emissions, combustion noise and fuel efficiency becomes feasible. In the scope of the engine design optimization, the simulation is an efficient tool in order to both predict the key performance parameters of the FIS, and to reduce the amount of experiments needed to reach the final product configuration. In this work a complete characterization of a solenoid ballistic injector for a Light-Duty Common Rail system was therefore implemented in a commercially available one-dimensional computational software called GT-SUITE. The main phenomena governing the injector operation were simulated by means of three sub-models (electro-magnetic, hydraulic and mechanical).

In the next incoming future the necessity of reducing the raw emissions leads to the challenge of an increment of the thermal engine efficiency. In particular it is necessary to increase the engine efficiency not only at full load but also at partial load conditions. In the open literature very few technical papers are available on the partial load conditions analysis. In the present paper the analysis of the effect of the throttle valve rotational direction on the mixture formation is analyzed. The engine was a PFI 4-valves motorcycle engine. The throttle valve opening angle was 17.2°, which lays between the very partial load and the partial load condition. The CFD code adopted for the analysis was the FIRE AVL code v. 2013.2. The exhaust, intake and compression phases till TDC were simulated: inlet/outlet boundary conditions from 1D simulations were imposed.

Direct Injection technology for Spark Ignition engines is currently undergoing a significant development process in order to achieve its complete potential in terms of fuel conversion efficiency, while preserving the ability to achieve future, stringent emission limits. In this process, improving the fuel spray analysis capabilities is of primary importance. Among the available experimental techniques, the momentum flux measurement is one of the most interesting approaches as it allows a direct measurement of the spray-air mixing potential and hence it is currently considered an interesting complement to spray imaging and Phase Doppler Anemometry. The aim of the present paper is to investigate the fuel spray evolution when it undergoes flash boiling, a peculiar flow condition occurring when the ambient pressure in which the spray evolves is below the saturation pressure of the injected fluid.

Diesel engine technology is continuously focused on higher performances and lower emission levels. Reduced costs and lower fuel consumption are key factors in engine development too, in particular for small diesel engine, both for on-road and non-road application. In order to fulfill emission legislation requirements, improve engine performance and reduce fuel consumption, nowadays the common rail injection system with electronic actuation is widely used in diesel engines. Nevertheless, conventional common rail system cost is quite high, mainly due to the complex indirect actuation of the injector, and the injector backflow leads to inefficiencies in the injection system. In this work an analysis of a medium pressure injection system for small diesel engines is presented, focusing on the achievable engine performances and emissions.

In an earlier study, a novel type of diesel fuel injector was proposed. This prototype injects fuel via porous (sintered) micro pores instead of via the conventional 6-8 holes. The micro pores are typically 10-50 micrometer in diameter, versus 120-200 micrometer in the conventional case. The expected advantages of the so-called Porous Fuel Air Mixing Enhancing Nozzle (PFAMEN) injector are lower soot- and CO2 emissions. However, from previous in-house measurements, it has been concluded that the emissions of the porous injector are still not satisfactory. Roughly, this may have multiple reasons. The first one is that the spray distribution is not good enough, the second one is that the droplet sizing is too big due to the lack of droplet breakup. Furthermore air entrainment into the fuel jets might be insufficient. All reasons lead to fuel rich zones and associated soot formation.

The effects of using blended renewable diesel fuel (30% vol.), obtained from Rapeseed Methyl Ester (RME) and Hydrotreated Vegetable Oil (HVO), in a Euro 5 small displacement passenger car diesel engine have been evaluated in this paper. The hydraulic behavior of the common rail injection system was verified in terms of injected volume and injection rate with both RME and HVO blends fuelling in comparison with commercial diesel. Further, the spray obtained with RME B30 was analyzed and compared with diesel in terms of global shape and penetration, to investigate the potential differences in the air-fuel mixing process. Then, the impact of a biofuel blend usage on engine performance at full load was first analyzed, adopting the same reference calibration for all the tested fuels.

In the present paper, the results of a detailed experimental analysis of a GDI spray based on Imaging, Phase Doppler Anemometry data and Momentum Flux distribution measurement are presented and discussed. The GDI system used is a three-hole research injector, operated in an injection pressure range of 50 bar to 150 bar. Spray Imaging is performed according to an ensemble average approach, acquiring images at different timings during the injection process; the resulting penetration and cone angle time-histories allow a quantitative description of the spray structure shape. Momentum flux distribution data are obtained by means of a dedicated test bench which detects the impact force of small spray portions. The sensing device is moved in different positions inside the spray structure, with the acquired force transients averaged on several injection events.

In the present paper the results of an experimental and numerical analysis of a common-rail, high pressure Diesel spray evolving in high counter pressure conditions is reported. The experimental study was carried out mainly in terms of spray momentum flux indirect measurement by the spray impact method; the measurement of the impact force time-histories, along with the CFD analysis of the same phenomenon, gave interesting insight in the internal spray structure. As well known, the overall spray structure momentum flux along with the injection rate measurements can be used to derive significant details about the in-nozzle flow and cavitation phenomena intensity. The same global spray momentum and momentum flux measurement can be useful in determining the jet-to-jet un-uniformities also in transient, engine-typical injection conditions which can assist in the matching process between the injection system and the combustion chamber design.