Search Results

As part of transformation from BS4 to BS6 automobile emission standard in India, engine manufactures are focusing on continuous development of emission control technologies and suitable strategies. Exhaust tail pipe emission and Crankcase emission are added together to meet the regulation acceptable limit. The crankcase emissions contribute substantially to the total Particulate Matter (PM) emitted from an engine. Hence there is a need of design and development of suitable Crankcase ventilation system. This paper presents investigation of high PM contributed from Open Crankcase ventilation (OCV) system in Diesel engine and experiment based solutions.

One of the important factors strongly required by customers nowadays is lower noise and vibration in vehicle. In this paper the prime focus is made on the study of effect of driveline angles on the noise and vibration behavior in a 4X4 configuration commercial vehicle. The impact of propeller shaft angles in the transfer of driveline excitations to the transmission and the resulting noise and vibration is studied. An abnormal noise was perceived from transmission and the root cause was investigated for the same. These excitations were high due to the higher driveline angles as this was design requirement to maintain higher ground clearance. A two-stage approach was adopted to modify the effect (transmission) and cause (propeller shaft angle) there by reducing the abnormal noise and vibration perceived in the vehicle.

In today's world with a dynamic market and varying customer expectations, it becomes inevitable that we find means of recognizing customer needs with all dimensions and instill them as inherent specifications of a product. Automobiles no way fall away from these intangible demands of the changing world, as personal conveyance (car/motorcycle/scooter) nowadays is more of a basic need. It becomes more of challenge to automotive manufacturers, to offer continuously improving quality products, at competitive prices to be in business. It's very important that as automotive designers we recognize quality in its totality and establish a predictive methodology to inculcate quality into the design at early stages of vehicle development.

In an era of global manufacturing and reduced costs, it is imperative that the manufacturing floor is visible to top management in a boardroom to enable them to make key decisions. Manufacturing Execution System (MES) is a method of connecting the shop floor to the top floor covering the complete gamut of activities from production sequence to finished goods. It aims to reduce the delay in transmitting production related data by linking the Production environment, Quality management, IT systems and Delivery. At Ashok Leyland’s Commercial Vehicle manufacturing facility in Ennore, India, an engine and axle components machine shop have been networked and data pertaining to production of Cylinder Block, Cylinder Head, Camshaft, Crankshaft, Axle Arm and Axle Beam components are accessible from anywhere in the company irrespective of location.

The primary factors influencing vehicle's dynamic behavior are the vehicle hard point definition, driver behavior and road inputs. The more the latter two are random and incorrigible in nature, the former one is quantifiable and can be controlled from designer's standpoint. In this paper, we have made an attempt to set targets to the vehicle hard point definition and thereby to optimize the vehicle for better ride behavior. This approach hence helped to converge to vehicle specifications set fundamentally designed to respond to random operating conditions and driving behavior intelligently. The work also involves study of various methodologies to predict roll, pitch, bounce and dive behaviors on a typical commercial passenger vehicle and is concluded by a sensitivity analysis to understand significance of these hard points on vehicle's real time behavior.

As technology gets upgraded every day, automotive manufacturers are paying more attention towards delivering a highly reliable product which performs its intended function throughout its useful life (without any failure). To develop a reliable product, accelerated combined stress testing should be conducted in addition to the conventional design validation protocol for the product. It brings out most of the potential failure modes of the product, so that necessary actions can be taken for the reliability improvement. This paper discusses about the field failure simulation and reliability estimation of automotive headlamp relays using accelerated combined stress testing. To analyze various field failure modes, performance and tear down analysis were carried out on the field failure samples. Field data (i.e. electrical, thermal and vibration signals) were acquired to evaluate normal use conditions.

In the present scenario, delivering right product at the right time is very crucial in automotive sector. Today, most of the OEMs have started to produce FBS (Fully Build Solution) such as oil tankers, mining tippers and two-wheeler carriers based on the market requirements. During product development phase, all automotive components undergo stringent validation protocol either in on-road or laboratory which consumes most of the product development time. This project is focused on developing validation methodology for two-wheeler carrier structure (deck) of a commercial vehicle. For this, road load data were acquired in the typical routes of customers at different loading conditions. Roads were classified as either good or bad based on the axle acceleration. To shorten the test duration, actual road load data was compressed using strain based damage editing techniques. The spectrum and transmissibility of acceleration signals at the decks were analyzed to select a deck for validation.

Traditional methods of noise control in most application are by using absorption and barrier techniques. These involve brackets & clamps for assembly, carrier material to hold absorbing materials. Usage of absorbing materials which could be high, as this is based on noise control technique by allowing source to produce noise and hence the cost is also higher. Based on the survey, several demerits have been studied in using absorption and barrier noise control techniques in the field of an automobile application. This paper deals with the noise control by using the application of free layer damping technique thereby overcoming the demerits happening in using former techniques, helping better control of noise in the environment and solutions which are more durable. The methodology followed here before going for the FLD application is identification of noise radiating components which needs to be damped in a system or subsystem.

In the emerging commercial vehicle sector, it is very essential to give a product to customer, which is very reliable and less prone to the failures to make the product successful in the market. In order to make it possible, the product is to be validated to replicate the exact field conditions, where it is going to be operated. Lab testing plays a vital role in reproducing the field conditions in order to reduce the lead time in overall product life cycle development process. This paper deals with the design and fabrication of the steering column slip endurance test rig. This rig is capable of generating wear on the steering column splines coating which predominantly leads to failure of steering column. The data acquired from Proving Ground (PG) was analyzed and block cycles were generated with help of data analyzing tools.

All automotive components, systems and vehicles undergo stringent validation protocol standards. Nevertheless, there are certain factors which cannot be captured during validation phase and result in field failures. With multiple players prying for market share in the automotive industry, timely resolution of field failures can go a long way in retaining customer base. In such a scenario, when customer’s tolerance on field failures is very limited, failures need severe attention and must be captured as early as possible to cut down warranty expenses. This project aims at creating a methodology to simulate field failures and validate improved design. The reliability parameters such as β (Shape Factor), η (Scale factor), Reliability and life are estimated and the values are compared between field and lab conditions. Life estimated in field conditions (Failure data base) and lab are correlated using Reliability techniques and target is established for validating improved sample.

Driver safety is one of the key considerations in truck design and development. Virtual simulation offers opportunities to reduce development time and the number of physical prototypes consumed for design verification and validation for safety parameters. Thus, the application of virtual simulations of crash has become an integral part of the vehicle development process. The continuously emerging scenarios involving challenging test requirements can only be tested by means of virtual simulation techniques. This paper presents simulations that are performed to verify various safety aspects to ensure crashworthiness of the truck cabin. The cabin structure was evaluated for various national/international safety regulations. The FE model and simulation methodology was validated through physical testing and correlated for frontal impact test and roof strength test as per AIS 029/ECE R29. Analysis performed to ensure compliance to upcoming regulation ECE R29 Revision 03 is also discussed.

A case study was conducted on the design, optimization and material replacement for an automobile suspension link. The link is part of a four bar mechanism. The mechanism was developed in Adams/Car® and multibody simulation was carried out on it. The joint forces arrived from the simulation were exported for finite element analysis of the components in OptiStruct®. Finally, topology and shape optimization was conducted to reduce the weight of the original component. A feasibility study was also carried out to replace the fabricated steel link with a heat treated cast iron link. Heat treated cast iron being lighter than steel, ensures reduction in weight without compromising on strength. The experiment resulted in a feasible optimized shape which was 32% lighter than the current shape of the link being used in the vehicle, while keeping the stresses and displacements within limits.

Evaluation of vehicle structural durability is one of the key requirements in design and development of today's automobiles. Computer simulations are used to estimate vehicle durability to save the cost and time required for building and testing the prototype vehicles. The objective of this work was to find the service life of automotive structures like passenger commercial vehicle (bus) and truck's cabin by calculating cumulative fatigue life for operation under actual road conditions. Stresses in the bus and cabin are derived by means of performing finite element analysis using inertia relief method. Multi body dynamics simulation software ADAMS was used to obtain the load history at the bus and cabin mount locations - using measured load data as input. Strain based fatigue life analysis was carried out in MSC-Fatigue using static stresses from Nastran and extracted force histories from ADAMS. The estimated fatigue life was compared with the physical test results.

Multi Body Dynamics (MBD) simulation software is used in product development cycle to reduce the lead time to market. These software have standard parametric templates for modeling metallic suspension systems, which can be quickly modified and used in full vehicle models for ride, handling analysis and the durability load predictions. Generally every Original Equipment Manufacturer (OEM) has unique air suspension arrangement and hence standard template is not available for air suspension modeling in commercial MBD software. Air suspension with self-leveling control mechanism is preferred over metallic suspension in the commercial passenger vehicle like bus for smooth ride comfort. Hence custom made templates for these systems need to be developed for use with MBD software. In this paper, a simplified model of air suspension is presented.

Spring seat plays major role in bogie suspension; which is guiding and controlling the leaf spring for better suspension and also to withstand the compressive load from leafs. Currently used spring seats are failing frequently in medium and heavy duty vehicles, which lead to customer concerns by higher idle time and part replacement cost. Thickness of the spring seat can't be increased by large extent due to packaging constraints in the vehicle. Stress levels identified by FEA method are found higher than the current material capacity. With these constraints, the spring seat has been re-designed with improved strength and ductility of material by modern technology - Austempered Ductile Iron (ADI). The parts have been developed and assembled in various tipper applications and performance was studied. The developed spring seat shows five times superior durability compare to existing design.

Commercial vehicle NVH attributes primarily focus on interior noise for driver's comfort and exterior noise for environmental legislation. Major sources for both the interior and exterior noise are power train unit, exhaust and air intake system. This paper focuses on development of Air Intake System (AIS) for better interior and exterior NVH performance for medium and heavy commercial vehicles. For air intake system, structural radiations from its panels and nozzle noise are significant contributors on overall vehicle NVH. Noise generation mechanism in air intake system occurs due to opening and closing of the valves and inlet air column oscillation by sharp pressure pulse from cylinder. Based on benchmarking, vehicle level targets have been arrived, and then cascaded to system and sub-system level targets. For air intake system, targets for nozzle noise at wide open throttle condition have been set for exterior NVH performance.

Automotive vehicles are subjected to a variety of loads caused by road undulations. The load history data measured from the roads are one of the vital input parameters for physical test as well as virtual durability simulation of vehicles. In general, the automotive vehicles are instrumented and subjected to a variety of driving conditions in diverse roads to obtain representative road load time histories. Acquired road load time history signals from various roads are exhaustive and repetitive in terms of both time length and data size. This results in more computation and virtual simulation processing. Hence it is imperative to reduce the input time signals without compromising on the representation of the actual operating conditions. Signal reduction of measured road load histories for virtual simulation assumes greater significance for durability prediction.

In the present scenario, delivering the right product at the right time is very crucial in automotive sector to grab the competitive advantage. In the development stage, validation process devours most of the product development time. This paper focuses on reducing the validation time for damper (shock absorber) variants which is a vital component in commercial vehicle suspension system. New test facility is designed for both performance test and endurance testing of six samples simultaneously. In addition, it provides force trend monitoring during the validation which increases the efficiency of test with an enhanced control system. This new facility is also designed to provide side loading capability for individual dampers in addition to the conventional axial loading. The key parameter during validation is control of damper seal temperature within the range of 70-90°C. A cooling circuit is designed to provide an efficient temperature control by re-circulating cold water.

Vehicular Emission testing is gaining importance over the past years in the wake of requirements for real driving emissions with implementation of RDE packages across Europe / USA and various developing countries. Extending the same concept for other countries poses slight challenges in terms of geographical and climatic conditions prevailing in the country, where the climatic conditions are differing from Europe / USA. It is a challenge to accept the same boundary conditions as in Europe, at the same time the challenge is to find a threshold number in a more scientific manner. This study concentrates on determination and recommendation of thresholds for ambient temperature and altitude. The basis for temperature threshold would be to determine the percentage of time the temperature exceeded beyond the threshold over year in the country. The basis for Altitude is considered based on the percentage of total length of roads beyond the threshold altitude limit.

Automotive component light weighing is one of the major goals for original equipment manufacturers (OEM's) globally. Significant advances are being made in developing light-weight high performance components. In order to achieve weight savings in vehicles, the OEM's and component suppliers are increasingly using ultra-high-strength steel, aluminum, magnesium, plastics and composites. One way is to develop a light weight high performance component through multi material concept. In this present study, a bimetal brake drum of inner ring cast iron and outer shell of aluminum has been made in two different design configurations. In two different designs, 40 and 26% weight saving has been achieved as compared to conventional gray cast iron brake drum. The component level performance has been evaluated by dynamometer test. The heat dissipation and wear behavior has been analyzed. In both designs, the wear performance of the bimetal brake drum was similar to the gray cast iron material.