Search Results

The objective of this project, which is supported by the U.S. Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL), is to provide a comprehensive comparison of heavy-duty trucks operating on alternative fuels and diesel fuel. Data collection from up to eight sites is planned. This paper summarizes the design of the project and early results from the first two sites. Data collection is planned for operations, maintenance, truck system descriptions, emissions, duty cycle, safety incidents, and capital costs and operating costs associated with the use of alternative fuels in trucking.

Chemical and physical properties of various plastics used for plastic abrasive applications are presented. All testing is done in compliance with MIL-P-85891 (AS), “Plastic Media for Removal of Organic Coatings”. Density and heavy density particle contamination are particularly important tests relative to aerospace applications.

Performance of various plastic abrasive materials is compared in a typical aerospace coatings removal application. Media aggressiveness towards substrates, stripping capabilities, effects of plastic breakdown, and plastic consumption are compared. Lower density plastics are shown to be more substrate protective than higher denisty plastics. Stripping rates are shown to be dependent both on plastic hardness and breakdown resistance of the plastic.

Of the several types of performance-based brake testers (PBBTs), roller dynamometers (RDs) have been used for more than 20 years in Europe to judge the braking capabilities of commercial vehicles and for enforcement of minimum brake performance requirements. These RDs, however, have been exclusively of the in-ground design. In recent years, both in Australia as well as in the United States, the use of portable RDs for assessing commercial vehicle braking performance has been increasing. This paper describes some of the differences between the two types of RDs. Analyses of the effect of the roll geometry and coefficient of friction on maximum brake force measurements are made. It is concluded that careful considerations must be taken with the use of such measurements for predicting stopping distance and braking stability using the results from both in-ground as well as portable RDs. Recommendations are made based on the results of the analyses.

The ability of performance-based brake testers (PBBTsa) to accurately determine the braking capability of commercial vehicles was investigated through a field study of over 2,800 trucks and buses. Under certain conditions, good agreement was found between the observation of brake-related defects by visual inspection and the measurement of weak brake forces by a PBBT. It was determined that the PBBTs' assessment was an independent measure of a vehicle's as-is braking capability, and should not be expected to correlate well with a visual inspection under any condition. It was also determined that predictions of stopping capability should be possible combining the PBBT results of the brake force and axle load measurements with certain assumptions regarding brake application time and road/tire coefficient of friction.

The impact dynamics of full-scale heavy-vehicle rollover events were quantitatively evaluated. Videotapes of a variety of rollover events were collected. One tractor-semitrailer combination was rolled by a sudden steer, two combinations rolled after a barrier impact, and one straight truck was pulled down an embankment. The videotapes were analyzed to estimate the vehicles' roll rates and their vertical velocities upon striking the ground. These experimental values corroborate the results of vehicle dynamic simulations that had been previously conducted to replicate actual rollover crashes. Those crashes were the subject of an NTSB Special Investigation Report that examined the crashworthiness of cargo tank trucks carrying hazardous materials.

This paper summarizes the Next Generation Natural Gas Vehicle (NG-NGV) Program that is led by the U.S. Department Of Energy's (DOE's) Office of Heavy Vehicle Technologies (OHVT) through the National Renewable Energy Laboratory (NREL). The goal of this program is to develop and implement one Class 3-6 compressed natural gas (CNG) prototype vehicle and one Class 7-8 liquefied natural gas (LNG) prototype vehicle in the 2004 to 2007 timeframe. OHVT intends for these vehicles to have 0.5 g/bhp-hr or lower emissions of oxides of nitrogen (NOx) by 2004 and 0.2 g/bhp-hr or lower NOx by 2007. These vehicles will also have particulate matter (PM) emissions of 0.01 g/bhp-hr or lower by 2004. In addition to ambitious emissions goals, these vehicles will target life-cycle economics that are compatible with their conventionally fueled counterparts.

A program has been completed to evaluate ultra-low sulfur diesel fuels and passive diesel particulate filters (DPFs) in truck and bus fleets operating in southern California. The fuels, ECD and ECD-1, are produced by ARCO (a BP Company) and have less than 15 ppm sulfur content. Vehicles were retrofitted with two types of catalyzed DPFs, and operated on ultra-low sulfur diesel fuel for over one year. Exhaust emissions, fuel economy and operating cost data were collected for the test vehicles, and compared with baseline control vehicles. Regulated emissions are presented from two rounds of tests. The first round emissions tests were conducted shortly after the vehicles were retrofitted with the DPFs. The second round emissions tests were conducted following approximately one year of operation. Several of the vehicles retrofitted with DPFs accumulated well over 100,000 miles of operation between test rounds.

The Advanced Petroleum-Based Fuels - Diesel Emissions Control (APBF-DEC) project is a joint U.S. government/industry research effort to identify optimal combinations of fuels, lubricants, engines, and emission control systems to meet projected emissions regulations during the period 2000 to 2010. APBF-DEC is conducting five separate projects involving light- and heavy-duty engine platforms. Four projects are focusing on the performance of emission control technologies for reducing criteria emissions using different fuels. This project is investigating the effects of lubricant formulation on engine-out emissions (Phase I) and the resulting impact on emission control systems (Phase II). This paper describes the statistical design and analysis methods used during Phase I of the lubricants project.

Currently the U. S. Department of Defense (DoD) exclusively uses potassium acetate (KAc)-based runway deicing fluids (RDFs) to deice and anti-ice military runways and taxiways. Commercial airports predominantly use KAc, but some also use RDFs composed of KAc plus propylene glycol (PG) or urea plus PG. Conventional RDFs have environmental concerns due to toxicity as well as material compatibility problems such as corrosion of aircraft carbon brake-pad components, cadmium-plated landing gear, and airfield lighting fixtures. Under the Strategic Environmental Research and Development Program (SERDP), Battelle tested a series of patented - bio-based RDFs to address these issues. Tests showed that the Battelle RDFs met the mandatory Aerospace Material Specification (AMS) 1435 requirements. These new RDFs have reduced ecotoxicity compared to currently used RDFs and are compliant with all other environmental requirements.

Tests were conducted during 2008 on 16 late-model, conventional vehicles (1999 through 2007) to determine short-term effects of mid-level ethanol blends on performance and emissions. Vehicle odometer readings ranged from 10,000 to 100,000 miles, and all vehicles conformed to federal emissions requirements for their federal certification level. The LA92 drive cycle, also known as the Unified Cycle, was used for testing as it was considered to more accurately represent real-world acceleration rates and speeds than the Federal Test Procedure (FTP) used for emissions certification testing. Test fuels were splash-blends of up to 20 volume percent ethanol with federal certification gasoline. Both regulated and unregulated air-toxic emissions were measured. For the aggregate 16-vehicle fleet, increasing ethanol content resulted in reductions in average composite emissions of both NMHC and CO and increases in average emissions of ethanol and aldehydes.

Increasing fuel costs and the desire for reduced dependence on foreign oil have brought the diesel engine to the forefront of future medium-duty vehicle applications in the United States due to its higher thermal efficiency and superior durability. One of the obstacles to the increased use of diesel engines in this platform is the Tier 2 emission standards. In order to succeed, diesel vehicles must comply with emissions standards while maintaining their excellent fuel economy. The availability of technologies-such as common rail fuel injection systems, low-sulfur diesel fuel, oxides of nitrogen (NOX) adsorber catalysts or NACs, and diesel particle filters (DPFs)-allows for the development of powertrain systems that have the potential to comply with these future requirements. In support of this, the U.S. Department of Energy (DOE) has engaged in several test projects under the Advanced Petroleum Based Fuels-Diesel Emission Control (APBF-DEC) activity [1, 2, 3, 4, 5].

Due to its high efficiency and superior durability, the diesel engine is again becoming a prime candidate for future light-duty vehicle applications within the United States. While in Europe the overall diesel share exceeds 40%, the current diesel share in the United States is 1%. Despite the current situation and the very stringent Tier 2 emission standards, efforts are being made to introduce the diesel engine back into the U.S. market. In order to succeed, these vehicles have to comply with emissions standards over a 120,000 miles distance while maintaining their excellent fuel economy. The availability of technologies-such as high-pressure, common-rail fuel systems; low-sulfur diesel fuel; oxides of nitrogen (NOx) adsorber catalysts or NACs; and diesel particle filters (DPFs)-allow the development of powertrain systems that have the potential to comply with the light-duty Tier 2 emission requirements. In support of this, the U.S.

Both field research and certification data show that the lean burn natural gas powered spark ignition engines offer particulate matter (PM) reduction with respect to equivalent diesel power plants. Concerns over PM inventory make these engines attractive despite the loss of fuel economy associated with throttled operation. Early versions of the Cummins L-10 natural gas engines employed a mixer to establish air/fuel ratio. Emissions measurements by the West Virginia University Transportable Heavy Duty Emissions Testing Laboratories on Cummins L-10 powered transit buses revealed the potential to offer low emissions of PM and oxides of nitrogen, (NOx) but variations in the mixture could cause emissions of NOx, carbon monoxide and hydrocarbons to rise. This was readily corrected through mixer repair or readjustment. Newer versions of the L-10 engine employ a more sophisticated fueling scheme with feedback control from a wide range oxygen sensor.

In this study, a 15-L heavy-duty diesel engine and an emission control system consisting of diesel oxidation catalysts, NOx adsorber catalysts, and diesel particle filters were evaluated over the course of a 2000 hour aging study. The work is a follow-on to a previously documented development effort to establish system regeneration and sulfur management strategies. The study is one of five projects being conducted as part of the U.S. Department of Energy's Advanced Petroleum Based Fuels - Diesel Emission Control (APBF-DEC) activity. The primary objective of the study was to determine if the significant NOx and PM reduction efficiency (>90%) demonstrated in the development work could be maintained over time with a 15-ppm sulfur diesel fuel. The study showed that high NOx reduction efficiency can be restored after 2000 hours of operation and 23 desulfation cycles.

The procedure utilized during a research evaluation of the effect of agglomerates in heavy fuels is described, and a simple light microscopic method for the study of particle dispersion in heavy fuels is given. The effectiveness of commercial additives for the treatment of heavy fuels to initiate dispersion is outlined as well as the development of a fast and inexpensive filtration test for accurately measuring the effect of various additives on various heavy fuels. Finally, the basic development work and the results obtained using ultrasonic dispersion of agglomerates during an actual engine performance test with heavy residual fuel oil is presented.

VTOL and STOL aircraft play a significant role in the ever increasing mobility of the Armed Forces. The landing gear of these aircraft must be able to operate from rough, unprepared fields and must support the aircraft on soft soil as well as on irregular and pothole terrain. This paper discusses the requirements of such gear and describes the development and design characteristics of tires and equipment that meet performance needs.

Application of electron microscopy to the study of fractures and fracture mechanisms is reviewed. Static fractures and the fracture of multiphased alloys have been studied, and significant information obtained. Striations on the fracture surface are associated with fatigue crack propagation and are directly related to crack growth rates. Various factors such as strength level, corrosive media, and second-phase particles are known to influence the appearance of the striations under the electron microscope. Since the appearance under the microscope of each type of fracture is quite unique, electron microscopic fractography is also an aid in service failure analyses.