Search Results

The objective of this project, which is supported by the U.S. Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL), is to provide a comprehensive comparison of heavy-duty trucks operating on alternative fuels and diesel fuel. Data collection from up to eight sites is planned. This paper summarizes the design of the project and early results from the first two sites. Data collection is planned for operations, maintenance, truck system descriptions, emissions, duty cycle, safety incidents, and capital costs and operating costs associated with the use of alternative fuels in trucking.

Chemical and physical properties of various plastics used for plastic abrasive applications are presented. All testing is done in compliance with MIL-P-85891 (AS), “Plastic Media for Removal of Organic Coatings”. Density and heavy density particle contamination are particularly important tests relative to aerospace applications.

Performance of various plastic abrasive materials is compared in a typical aerospace coatings removal application. Media aggressiveness towards substrates, stripping capabilities, effects of plastic breakdown, and plastic consumption are compared. Lower density plastics are shown to be more substrate protective than higher denisty plastics. Stripping rates are shown to be dependent both on plastic hardness and breakdown resistance of the plastic.

Optimization parameters designed to minimize residual stress and maximize coatings removal rates are presented. Stress saturation curves are presented and compared for the optimized blasting parameters using different plastic abrasive materials.

The ability of performance-based brake testers (PBBTsa) to accurately determine the braking capability of commercial vehicles was investigated through a field study of over 2,800 trucks and buses. Under certain conditions, good agreement was found between the observation of brake-related defects by visual inspection and the measurement of weak brake forces by a PBBT. It was determined that the PBBTs' assessment was an independent measure of a vehicle's as-is braking capability, and should not be expected to correlate well with a visual inspection under any condition. It was also determined that predictions of stopping capability should be possible combining the PBBT results of the brake force and axle load measurements with certain assumptions regarding brake application time and road/tire coefficient of friction.

The impact dynamics of full-scale heavy-vehicle rollover events were quantitatively evaluated. Videotapes of a variety of rollover events were collected. One tractor-semitrailer combination was rolled by a sudden steer, two combinations rolled after a barrier impact, and one straight truck was pulled down an embankment. The videotapes were analyzed to estimate the vehicles' roll rates and their vertical velocities upon striking the ground. These experimental values corroborate the results of vehicle dynamic simulations that had been previously conducted to replicate actual rollover crashes. Those crashes were the subject of an NTSB Special Investigation Report that examined the crashworthiness of cargo tank trucks carrying hazardous materials.

A program has been completed to evaluate ultra-low sulfur diesel fuels and passive diesel particulate filters (DPFs) in truck and bus fleets operating in southern California. The fuels, ECD and ECD-1, are produced by ARCO (a BP Company) and have less than 15 ppm sulfur content. Vehicles were retrofitted with two types of catalyzed DPFs, and operated on ultra-low sulfur diesel fuel for over one year. Exhaust emissions, fuel economy and operating cost data were collected for the test vehicles, and compared with baseline control vehicles. Regulated emissions are presented from two rounds of tests. The first round emissions tests were conducted shortly after the vehicles were retrofitted with the DPFs. The second round emissions tests were conducted following approximately one year of operation. Several of the vehicles retrofitted with DPFs accumulated well over 100,000 miles of operation between test rounds.

After several alternative procedures were investigated for preparing chromium-plated zinc die castings for painting, one procedure proved best for contaminated chromium surfaces. This procedure included six steps: (1) alkaline spray cleaning, (2) electrolytic alkaline cleaning, (3) rinsing with high-purity water with a specific resistance of 500,000-700,000 ohm-cm, (4) immersing in chromic acid solution (0.05 oz/gal) at 150 F for 2 minutes, or treating cathodically in 0.7 oz/gal of sodium dichromate with a current density of 0.05 amp/sq ft for 30-60 sec, (5) rinsing with high-purity water, (6) forced-air drying with filtered air at 15 psi. Good adherence was obtained by following these procedures and painting with a single coat of acrylic or alkyd-resin paint. Other preparation procedures resulted in inferior paint adherence.

This paper addresses the modeling issues of resistance spot welds. The state of the art modeling techniques on weld process simulation, weld property prediction and weld engineering performance evaluation are presented. First, weld process simulation is performed using the incrementally coupled thermal-electrical-mechanical analyses. The resulted weld nugget size, weld residual stress and weld material property distributions are then used in determining the static performance of a single weld coupon. Comparisons with experimental measurements are presented as validations. Results generated from this single weld coupon is then used in the simulation of dynamic crush mechanism of a spot welded single hat section.