Search Results

Initial preliminary development phases of two distinct SP-100 control drive assembly bearing test programs were successfully completed at elevated temperature in vacuum. The first was for the reflector drive line spherical self-aligning bearings. Each bearing consisted of a carbon-graphite ball mounted on an aluminum oxide-coated Ta-10%W shaft, captured by an aluminum oxide-coated Ta-10%W socket. One set of these bearings was exposed to temperatures up to 1180K (1665°F) at 1.33x10-6 Pa (1x10-8 torr) and subjected to 38000 cycles of motion. Friction coefficients were found to be between 0.11 and 0.25 over the full range of operation. Overall performance of the bearings was excellent, with only slight wear observed. The second test program was for the safety rod slider bearing. Zirconium carbide coated Nb-1%Zr bearing pads were stroked inside a molybdenum tube at temperatures up to 1422K (2100°F) at ∼1.33x10-6 Pa with a normal load of 1.02 Kg between each sliding surface.

The SP-100 reactor will operate at temperatures up to 1500K in high vacuum. Development of bearing coatings is necessary to avoid self welding and/or galling of moving components. No experience base exists for these conditions-the early SNAP (Space Nuclear Auxiliary Power) program requirements were over 400K lower with shorter lifetime requirements. To address the SP-100 needs, a tribology development program has been established at GE to investigate candidate coating materials. Materials were selected based on their high thermodynamic stability, high melting point, compatibility with the substrate, and coefficients of thermal expansion similar to niobium-1% zirconium - the candidate structural material for SP-100. An additional requirement was that the deposition processes should be commercially available to coat large components.

As part of the SP-100 Space Reactor Power System Program being undertaken for the U. S. Department of Energy, GE is developing a thermoelectric (T/E) power converter which utilizes reactor delivered heat and transforms it into usable electric power by purely static means. This converter is based to GE's product line of successful thermoelectric space power systems. The SP-100 power converter embodies the next generation improvement over the type of T/E converter successfully flown on the six U. S. space missions. That is, conduction coupling of T/E cell to both the heat source and the heat rejection elements. The current technology utilizes radiation coupling in these areas. The conduction coupling technique offers significant improvements in system specific power since it avoids the losses associated with parasitic ΔT's across the radiation gap between the heat source and the hot junction of the thermoelectric (T/E) cell.

The approach that was utilized to start up and requalify manufacture of the thermoelectric unicouple devices for the Cassini RTG (Radioisotope Thermoelectric Generator) program are described in this paper. Key elements involved in this effort were: engineering review of specifications; training of operators; manufacturing product verification runs; and management review of results. Appropriately, issues involved in activating a fabrication process that has been idle for nearly a decade, such as upgrading equipment, adhering to updated environmental, health, and safety requirements, or approving new vendors, are also addressed. The cumulative results of the startup activities have verified that a production line for this type of device can be reopened successfully.

System level design studies of space applications ranging in power from 77 kWt to 200 MWt have indicated no practical limit to the thermal power that can be reliably generated by a space reactor system based on the technologies being developed in the SP-100 program. These technologies include uranium nitride fuel, PWC-11/rhenium bonded fuel cladding, PWC-11 structural material for the lithium coolant boundary, electromagnetic coolant pumps, safety and reactivity control drive mechanisms, sensors, shielding materials, etc. at operating temperatures up to 1400K. The physical arrangements and characteristics of the nuclear reactor materials are described. The physical size of components and the arrangement of components change, but the basic technologies required are generally the same, irrespective of the total power output.

This paper describes how the SP-100 Space Reactor Power System (SRPS) can be tailored to meet the specific requirements for a lunar surface power system to meet the needs of the consolidation and utilization phases outlined in the 90-day NASA SEI study report. This same basic power system can also be configured to obtain the low specific masses needed to enable robotic interplanetary science missions employing Nuclear Electric Propulsion (NEP). In both cases it is shown that the SP-100 SRPS can meet the specific requirements. For interplanetary NEP missions, performance upgrades currently being developed in the area of light weight radiators and improved thermoelectric material are assumed to be technology ready in the year 2000 time frame. For lunar applications, some system rearrangement and enclosure of critical components are necessary modifications to the present baseline design.

Aircraft starting and generating systems heretofore have been largely the result of joining together available components. Recent studies have demonstrated that substantial benefits in weight, cost, size, and performance may be realized through a total system approach. This paper identifies the types of information required, and the methods of system analysis employed, to design an optimized system.

The principal design features of the NASA QCSEE UnderThe-Wing and Over-The-Wing powered lift propulsion systems are given. In the UTW engine, these include noise reduction features, a variable pitch low pressure ratio fan, a fan drive reduction gear, an advanced core and low pressure turbine with a low pollution combustor, a digital control, and advanced composite construction for the inlet, fan frame, fan exhaust duct, and variable area fan exhaust nozzle. The OTW engine is similar but has higher fan pressure and a fixed pitch fan. Both engines are scheduled to be fabricated and tested starting in 1976.

The major technological developments which have made possible the trend towards higher temperatures in modern aircraft gas turbine engines are discussed. The relative importance of manufacturing processes, material developments, cooling techniques, analytical design procedures, rupture and cyclic life considerations, and aerodynamic and mechanical design improvements are discussed along with illustrative examples and technical data. The need for a balanced design approach is stressed, and examples are given where trade-offs can be made. It is noted that the advances in aircraft engines during the last 10 years have been based on the evolution of sound engineering principles, extensive component and engine development, and careful consideration of the operational requirements rather than a tremendous breakthrough or revolutionary concept in any one area.

The problems and choices in the design of an advanced subsonic transport turbofan for reduced noise and improved aircraft performance are examined in this paper. The effects of bypass ratio, fan pressure ratio, and fan tip speed on jet noise, fan noise, and acoustic treatment suppression are described. The results do not indicate a clear optimum bypass ratio considering the effects upon installed engine performance and weight as well as acoustic performance. Low fan tip speed designs with the associated high aerodynamic loading are compared to high tip speed low loading designs. Other factors affecting noise such as the installation and other noise sources are discussed. The long duct installation is indicated to have potential advantages over the short duct separate flow installation. The problem of assuring that growth models of an engine also have low noise is discussed.

A four-legged, 3000 lb, walking truck test bed has been developed and the test results have proved the feasibility of walking machines. Effectiveness of this control method where the machine mimics man’s arm and leg movements was shown by a variety of maneuverability experiments. Therefore, it has been proved that it is possible to develop this vehicle concept, and the control method involved, to effectively emulate animals in the way they travel on rough terrain. Human perception, judgment, and agility are transmitted through the machine in a manner that lets the operator easily imagine that the machine is merely an effective extension of his own appendages. The human psychomotor action, coupled with the power and ruggedness of the machine, provides a valuable marriage. It opens new vistas not only for rough terrain vehicles but also for a variety of other manipulative machines. Many jobs require the sensing acuity of man but are too tough for the frail human flesh.

Alternative engine concepts to the advanced high bypass turbofan which have promise of reducing energy consumption including regenerative cycles and other engines with heat exchangers, unconventional engine arrangements such as geared fan engines, and high disc loading turboprops. After initial screening, several concepts were selected for a systematic evaluation of the merits of each relative to a high bypass turbofan based on advanced technology consistent with the mid 1980's time period. Both mission fuel and direct operating cost for typical long range transport missions were considered in the evaluation.

An acceleration of metal replacement to reinforce thermoplastic composites is positioned to impact the transportation markets through a joint venture between PPG Industries and GE Plastics, called AZDEL, Inc. The strength of both companies' strong technological base in glass and engineering thermoplastic resins is the key. The resulting long continuous glass thermoplastic composites have high strength to weight ratios, provide tough durable products, facilitate combining functions in design, and because of its high speed manufacturing processes, is cost effective. In addition, these materials can be post fabricated during the assembly phase, easily repaired and conveniently recycled. Value added secondary operations for both the captive or custom molders provide another avenue for cost reductions.