Search Results

This investigation utilizes a DFSS analysis approach to determine automatic transmission gear content required to minimize fuel consumption for various powertrain - vehicle systems. L18 and L27 inner arrays with automatic transmission design and shift pattern constraint parameters were varied to determine their relative influence on fuel consumption. An outer noise array consisting of two vehicles with various engines, final drive ratios and legislated emissions test cycles was used to make a robust transmission selection based on minimizing fuel consumption. The full details of the DFSS analysis method and assumptions are presented along with a detailed examination of the results. With respect to transmission design parameters, parasitic spinloss and gear mesh efficiency were found to be most important followed by the number of gears. The DFSS analysis further revealed that unique transmission design formulations are potentially required for widely varying engines.

Fatigue behavior of aluminum alloys under multiaxial loading was investigated with both cast aluminum A356-T6 and wrought alloy 6063-T6. The dominant multiaxial fatigue crack preferentially nucleates from flaws like porosity and oxide films located near the free surface of the material. In the absence of the flaws, the cracking/debonding of the second phase particles dominates the crack initiation and propagation. The number of cracked/debonded particles increases with the number of cycles, but the damage rate depends on loading paths. Among various loading paths studied, the circle loading path shows the shortest fatigue life due to the development of complex dislocation substructures and severe stress concentration near grain/cell boundaries and second phase particles.

The European Commission (EC) as well as the United States Environmental Protection Agency (EPA) published legislations to regulate or encourage the use of low Global Warming Potential (GWP) refrigerants applied to Mobile Air Conditioning (MAC) systems. Europe mandates a GWP less than 150 of MAC refrigerants for new vehicle types. The thermodynamic refrigerant properties of R-1234yf are slightly different from the properties of R-134a, currently used in MAC systems. Although the basic material data show that R-1234yf is flammable, ignition tests performed for an automotive engine under-hood environment reveal design and packaging influences of its ignition behavior. After extensive collaborative research in 2009, the Society of Automotive Engineers Cooperative Research Team (SAE CRP1234) concluded that R-1234yf is suitable for use in automotive applications. Further ignition risk assessment regarding R-1234yf usage in MAC systems was done by SAE CRP1234-4 in 2013.

It is obvious at this point even to the most casual observer of the automotive industry that efforts to reduce mass throughout the vehicle are at a fervor. The industry is facing its most significant increase in fuel economy standards in its history, and light-weighting the vehicle is a major enabler. Despite the performance and quality of the brake system being intensely related to its mass, it too has not been spared scrutiny. However, like many modern automotive subsystems, it is very complex and mass reduction opportunities that do not sacrifice performance or quality are not always obvious. There are some interesting and sometimes even profound relationships between mass and other vehicle attributes built into brake system design, and making these more visible can enable a better balancing of brake system with the rest of the vehicle design objectives. Examples include - what is the cost, in terms of brake system mass, of added engine power? Of tire and wheel size?

This investigation utilizes energy analysis and statistical methods to optimize step gear automatic transmissions gear selection for fuel consumption. A full factorial matrix of simulations using energy analysis was performed to determine the optimal number of gears and gear ratios that provide the best fuel consumption performance for a particular vehicle - engine application. The full factorial matrix setup as a design of experiment (DOE) was applied to five vehicle applications, each with two engines to examine the potential differences that variations in road load and engine characteristics might have on optimal transmission gearing selection. The transmission gearing options considered in the DOE were number of gears, launch gear ratio and top gear ratio. Final drive ratio was also included due to its global influence on vehicle performance and powertrain operating speeds and torque.

Fuel lean combustion and exhaust gas dilution are known to increase the thermal efficiency and reduce NOx emissions. In this study, experiments are performed to understand the effect of equivalence ratio on flame kernel formation and flame propagation around the spark plug for different low turbulent velocities. A series of experiments are carried out for propane-air mixtures to simulate engine-like conditions. For these experiments, equivalence ratios of 0.7 and 0.9 are tested with 20 percent mass-based exhaust gas recirculation (EGR). Turbulence is generated by a shrouded fan design in the vicinity of J-spark plug. A closed loop feedback control system is used for the fan to generate a consistent flow field. The flow profile is characterized by using Particle Image Velocimetry (PIV) technique. High-speed Schlieren visualization is used for the spark formation and flame propagation.

Development of the next generation internal combustion engines and automatic transmissions for automotive applications is a mandatory powertrain engineering activity required now and in the coming years to meet forthcoming global emissions regulations. This paper details a preliminary investigation into possible synergies for fuel consumption reduction considering emerging automotive technologies integrated into the next generation combustion engine and automatic transmission architectures. A range of hypothetical gasoline engines were created and paired with a generalized set of step gear automatic transmissions designed to meet the performance requirements of high volume longitudinal full size truck application. These designs were then run through a design of experiments orthogonal array for prediction of fuel consumption on the WLTP test schedule and stand still acceleration to 100 kph.

With the ever increasing pressure to improve the fuel economy of vehicles, there has been a corresponding interest in reducing the mass and size of vehicles. While mass is easily quantifiable, vehicle size, particularly the notion of “interior space” as perceived by the customer, is not. This paper explores different ways in which vehicle spaciousness can be quantified and explores new metrics based on customer verbatims. A novel ‘spaciousness calculator’ combines individual metrics to provide a singular holistic rating for spaciousness, useful during vehicle development. Beyond spaciousness, the paper discusses techniques to quantify the ‘packaging efficiency’ of a vehicle; this allows engineers to maximize the interior space for a given exterior size.

An area of brake system design that has remained continually resistant to objective, computer model based predictive design and has instead continued to rely on empirical methods and prior history, is that of sizing the brake pads to insure satisfactory service life of the friction material. Despite advances in CAE tools and methods, the ever-intensifying pressures of shortened vehicle development cycles, and the loss of prototype vehicle properties, there is still considerable effort devoted to vehicle-level testing on public roads using “customer-based” driving cycles to validate brake pad service life. Furthermore, there does not appear to be a firm, objective means of designing the required pad volume into the calipers early on - there is still much reliance on prior experience.

This paper compares the material consumption and fire patterns which developed on four nearly identical compact sedans when each was burned for exactly the same amount of time, but with different wind speed and direction during the burns. This paper will also compare the effects of environmental exposure to the fire patterns on the vehicles. The burn demonstrations were completed at an outdoor facility in southeast Michigan on four late model compact sedans. The wind direction was controlled by placing the subject vehicle with either the front facing into the wind, or rear facing into the wind. Two of the burns were conducted when the average observed wind speed was 5-6kph and two of the burns were conducted at an average observed wind speed of 19kph.

A rough road ride assessment provides an insightful evaluation of vehicle responses beyond the frequency range of suspension or steering modes. This is when body structure influence on the vehicle performance can be detected by vehicle occupants. In this paper, a rough road is used to evaluate vehicle ride performance and multi-body simulation (MBS) models are developed along with finite-element (FE) representations of the vehicle body and structure. To produce high fidelity simulation results in the frequency range of interest, various vehicle subsystem modeling contents are examined. A case study of a vehicle model with two different structures is provided. Time histories and frequency based analyses are used to obtain insights into the effects of body structure on vehicle responses. Finally, two metrics (‘Isolation’ and ‘Shake’) are used to distinguish the vehicle ride performance.

Oil canning and initial stiffness of the automotive roofs and panels are considered to be sensitive customer ‘perceived quality’ issues. In an effort to develop more accurate objective requirements, respective simulation methods are continuously being developed throughout automotive industries. This paper discusses a latest development on oil canning predictions using LS-DYNA® Implicit, including BNDOUT request, MORTAR contact option and with the stamping process involved, which resulted in excellent correlations especially when it comes to measurements at immediate locations to the feature lines of the vehicle outer panels. Furthermore, in pursuit of light-weighting vehicles with thinner roofs, a new CAE method was recently developed to simulate severe noise conditions exhibited on some of developmental properties while going through a car wash.

Modification of gasoline blendstock composition in preparing ethanol-gasoline blends has a significant impact on vehicle exhaust emissions. In “splash” blending the blendstock is fixed, ethanol-gasoline blend compositions are clearly defined, and effects on emissions are relatively straightforward to interpret. In “match” blending the blendstock composition is modified for each ethanol-gasoline blend to match one or more fuel properties. The effects on emissions depend on which fuel properties are matched and what modifications are made, making trends difficult to interpret. The purpose of this paper is to illustrate that exclusive use of a match blending approach has fundamental flaws. For typical gasolines without ethanol, the distillation profile is a smooth, roughly linear relationship of temperature vs. percent fuel distilled.

The need for improved vehicle energy efficiency has increased greatly in recent years along with regulatory fuel economy standards. One key aspect of energy efficiency for both conventional and alternative propulsion vehicles is the energy efficiency of the electrical architecture. In the design of electrical architectures there are several techniques available to increase the energy efficiency. One technique is to manage CAN serial data communication by using Partial Networks. This paper describes a model based approach for simulating the vehicle network behavior when CAN Partial Networking is used as the strategy for need based ECU activation. The simulation results will in turn provide ECU power consumption data to support various electrical architecture design decisions.

Development of the software using fixed-point arithmetic is known to be tedious and error-prone. Difficulty of selecting the correct data type can outwear software developers. The common retreats often sought after include manual calculation of the approximate ranges, exhaustive simulations with extreme input values and conservative development approach by using excessive word length. The first two retreats - manual calculation and exhaustive simulations - increase the software development time, and the third retreat - conservative development - leads to the excessive memory (RAM and ROM) utilization by the software. The model-based development environment such as the Simulink has graphical nature to the software with flow of data defined by connecting signal lines. The model-based software therefore gives an opportunity to trace signal flow in the software. Input-tracing method is presented to trace the flow of the input signals of the user selected block in the software model.

Rapidly increasing customer, financial, and regulatory pressures are creating clear changes in the calculus of vehicle design for modern automotive OEM's (Original Equipment Manufacturers). Customers continue to demand shorter product lifecycles; the increasingly competitive global market exerts pressure to reduce costs in all stages of development; and environmental regulations drive a continuous need to reduce mass and energy consumption. OEM's must confront these challenges while continuing to satisfy the customer. The foundation to meeting these challenges includes: (1) Continued development of objective metrics to quantify performance; (2) Frontloading vehicle design content and performance synthesis; (3) A precise understanding of the customer and their performance preferences under diverse usage conditions. These combined elements will enable products better optimized amongst competing (and often contradictory) imperatives.

Passenger vehicle engine cooling systems typically fall into surge tank or recovery type systems. Recovery systems rely on an expansion/recovery volume, which operates at atmospheric pressure. Over long periods of time and with elevated temperatures, coolant evaporates from this atmospheric recovery bottle. An experimental study determined the evaporation rate as a function of temperature for one bottle geometry. A 1-D model then projected the total coolant loss to evaporation over several different hypothetical customer duty cycles to evaluate robustness of recommended service intervals.

Diesel particulate filter (DPF) is a widely used emission control device on diesel vehicles. The DPF captures the particulate matter coming from the engine exhaust and periodically burns the collected soot via the regeneration process. There are various trigger mechanisms for this regeneration, such as distance, time, fuel and simulation. Another method widely used in the industry is the pressure drop across the filter. During calibration, relation between the pressure sensor reading and soot mass in the filter is established. This methodology is highly effective in successful DPF operation as pressure sensor is a live signal that can account for any changes in engine performance over time or any unforeseen hardware failures. On the other hand, any erroneous feedback from the sensor can lead to inaccurate soot mass prediction causing unnecessary regenerations or even needless DPF plugging concerns.

A hot and cold water mixing process with a steam condenser and a chilled water heat exchanger is set up for an engine EGR fouling test. The test rig has water recycled in the loop of a pump, heat exchangers, a three-way mixing valve, and a test EGR unit. The target unit temperature is controlled by a heating, cooling and mixing process with individual valves regulating the flow-rate of saturated steam, chilled water and mixing ratio. The challenges in control design are the dead-time, interaction, nonlinearity and multivariable characteristics of heat exchangers, plus the flow recycle in the system. A systems method is applied to extract a simple linear model for control design. The method avoids the nonlinearity and interaction among different temperatures at inlet, outlet and flow-rate. The test data proves the effectiveness of systems analysis and modeling methodology. As a result, the first-order linear model facilitates the controller design.

Future diesel combustion systems may operate with significantly higher levels of boost and EGR than used with present systems. The potential benefits of higher boost and EGR were studied experimentally in a single-cylinder diesel engine with capability to adjust these parameters independently. The objective was to study the intake and exhaust conditions with a more optimum combustion phasing to minimize fuel consumption while maintaining proper constraints on emissions and combustion noise. The engine was tested at four part-load operating points using a Design of Experiments (DOE) approach. Two of the operating points correspond to low-speed and low-load conditions relevant for the New European Driving Cycle (NEDC). The other two points focus on medium load conditions representative of the World-wide harmonized Light-duty Test Procedures (WLTP).