Search Results

Technologies for improving the fuel economy of gasoline engines have been vigorously developed in recent years for the purpose of reducing CO2 emissions. Increasing the compression ratio for improving thermal efficiency and downsizing the engine based on fuel-efficient operating conditions are good examples of technologies for enhancing gasoline engine fuel economy. A direct-injection system is adopted for most of these engines. Direct injection can prevent knocking by lowering the in-cylinder temperature through fuel evaporation in the cylinder. Therefore, direct injection is highly compatible with downsized engines that frequently operate under severe supercharging conditions for improving fuel economy as well as with high compression ratio engines for which susceptibility to knocking is a disadvantage.

Technologies for improving the fuel economy of gasoline engines have been vigorously developed in recent years for the purpose of reducing CO2 emissions. Increasing the compression ratio is an example of a technology for improving the thermal efficiency of gasoline engines. A significant issue of a high compression ratio engine for improving fuel economy and low-end torque is prevention of knocking under a low engine speed. Knocking is caused by autoignition of the air-fuel mixture in the cylinder and seems to be largely affected by heat transfer from the intake port and combustion chamber walls. In this study, the influence of heat transfer from the walls of each part was analyzed by the following three approaches using computational fluid dynamics (CFD) and experiments conducted with a multi-cooling engine system. First, the temperature rise of the air-fuel mixture by heat transfer from each part was analyzed.

For diesel engine, lower compression ratio has been demanded to improve fuel consumption, exhaust emission and maximum power recently. However, low compression ratio engine might have combustion instability issues under cold temperature condition, especially just after engine started. As a first step of this study, cold temperature combustion was investigated by in-cylinder pressure analysis and it found out that higher heat release around top dead center, which was mainly contributed by pilot injection, was the key factor to improve engine speed fluctuation. For further understanding of combustion in cold condition, particularly mixture formation near a glow plug, 3D CFD simulation was applied. Specifically for this purpose, TI (Time-scale Interaction) combustion model has been developed for simulating combustion phenomena. This model was based on a reasonable combustion mode, taking into account the characteristic time scale of chemical reactions and turbulence eddy break-up.

The use of CAE software in developing plastic components has advanced rapidly in recent years. This progress has been supported by the development of practical analytical tools, based on the finite element and boundary element methods, and on the dramatic improvements seen in computer performance. Following the introduction of a flow analysis program in 1982, Nissan has developed and implemented advanced programs for use in developing plastic components and has integrated the programs into a unified in-house system. This system is being utilized at the design and manufacturing stages of interior and exterior trim parts and has produced concrete results in different phases of component development. Work is now proceeding on the development of a system that can simultaneously analyze both the component performance and the factors that need to be considered in the manufacturing process.

Sophisticated product designs enrich people's lives and social demands for creation of good designs are quite strong. In the automobile industry, good design quality is one of the principal factors for determining market competitiveness. In this situation where good design quality is required of every product, the authors have developed a CAD/CAM system which makes it possible to create good and accurate designs by translating designers' ideas directly and quickly into high quality CAD models, a capability that has long been desired. With this high performance system, freely formed curves and surfaces can be easily manipulated with a man-machine interface familiar to industrial designers accutomed to the conventional design process. The system also integrates photo-realistic rendering, stereography and NC milling machines for verifying differences between the realized shape and the image in the designer's mind.

It is well known that the wheels and tires account for approximately 25% of the overall aerodynamic drag of a vehicle. This is because the contribution of the tires to aerodynamic drag stems from not only aerodynamic drag itself directly caused by exposure to the main flow (tire CD), but also from aerodynamic drag indirectly caused by the interference between tire wakes and the upper body flow (body CD). In the literature, as far as the authors are aware, there have been no reports that have included the following all four aspects at once: (1) CD sensitivity to detailed tire shape factors; (2) CD sensitivity differences due to different vehicle body types; (3) CD sensitivity for each aerodynamic drag component, i.e., tire CD and body CD; (4) Flow structure and mechanism contributing to each aerodynamic drag component. The purpose of this study was to clarify CD sensitivity to tire shape factors for tire CD and body CD considering two different vehicle body types, sedan and SUV.

A voxel model, which consists of minute cubic cells called voxels to express the shape of an object, can now be generated automatically from CAD data. Moreover, advances in high-speed computational techniques have made it possible to perform a structural analysis using such a voxel model. This paper presents some high-speed computational techniques to realize the analysis in practice and a method to treat a contact condition on the jagged surface that characterizes a voxel model to further expand the scope of application.

Increasing expectations for stability at high speed call for the improvement of cars' aerodynamic performance, in particular lift reduction. However, due to styling constraints, traditional spoilers must be avoided and replaced by other solutions like underfloor components. Flow simulation is expected to be a useful tool for lift prediction, but the conventional models used so far did not represent complex geometry details such as the engine compartment and underfloor, and accuracy was insufficient. In the present study, a full vehicle simulation model, including the engine compartment and underfloor details, was used. Other improvements were also made such as optimization of the computational grid and the setting of boundary conditions for reproducing wind tunnel experiments or actual driving, making it possible to predict lift variations due to vehicle geometry changes.

Gasoline engines employ various mechanisms for improvement of fuel consumption and reduction of exhaust emissions to deal with environmental problems. Direct fuel injection is one such technology. This paper presents a new quasi-dimensional combustion model applicable to direct injection gasoline engine. The Model consists of author's original in-cylinder turbulence and mixture homogeneity sub model suitable for direct fuel injection conditions. Model validation results exhibit good agreement with experimental and 3D CFD data at steady state and transient operating conditions.

A combined computational fluid dynamics (CFD) and finite element (FE) analysis approach has been developed to simulate in the early stages of design the temperature distribution and estimate the thermal fatigue life of an engine exhaust manifold. To simulate the temperature distribution under actual operating conditions, we considered the external and internal flow fields. Digital mock-ups of the vehicle and engine were used to define the geometry of the engine compartment. External-air-flow simulation using in-house CFD code was used to predict the flow fields in the engine compartment and the heat transfer coefficients between the air and the exhaust manifold wall at various vehicle speeds. Unsteady-gas-flow calculation using the STAR-CD thermal- fluids analysis code was to predict the heat transfer coefficients between the exhaust gas and the manifold wall under various operating conditions.

Electronic control of automatic transmission systems have become indispensable in order to satisfy driver expectations of comfort and vehicle response. The increasing complexity of such systems has resulted in a huge increase of control data volumes handled by electronic transmission control units (ETCUs). This paper describes the development, operation and evaluation by JATCO Corporation and Nissan Motor Co., Ltd of a Read Only Memory (ROM) management system for use with ETCUs. The system makes extensive use of computer aided design(CAD) techniques to create ROM data from standard format drawings, and vice-versa. The paper also presents the evaluation system developed for ETCU use. Making use of computer simulated testing, this increases the reliability of units and reduces testing time.

Evaluations of dummy injury readings obtained in regulatory crash tests and new car assessment program tests provide indices for the development of crash safety performance in the process of developing new vehicles. Based on these indices, vehicle body structures and occupant restraint systems are designed to meet the required occupant injury criteria. There are many types of regulatory tests and new car assessment program tests that are conducted to evaluate vehicle safety performance in side impacts. Factoring all of the multiple test configurations into the development of new vehicles requires advanced design capabilities based on a good understanding of the mechanisms producing dummy injury readings. In recent years, advances in computer-aided engineering (CAE) tools and computer processing power have made it possible to run simulations of occupant restraint systems such as side airbags and seatbelts.

This paper describes a study of drag reduction devices for production pick-up trucks with a body-on-frame structure using full-scale wind tunnel testing and Computational Fluid Dynamics (CFD) simulations. First, the flow structure around a pick-up truck was investigated and studied, focusing in particular on the flow structure between the cabin and tailgate. It was found that the flow structure around the tailgate was closely related to aerodynamic drag. A low drag flow structure was found by flow analysis, and the separation angle at the roof end was identified as being important to achieve the flow structure. While proceeding with the development of a new production model, a technical issue of the flow structure involving sensitivity to the vehicle velocity was identified in connection with optimization of the roof end shape. (1)A tailgate spoiler was examined for solving this issue.

Every year the trucking industry demands lighter weight and lower cost truck components. But it is very difficult to achieve both these targets. This paper describes the example of a suspension system design which was conducted by computer simulation, so called CAE. The computer simulation by FEM was used completely to decide the detailed shape of each part. This paper also introduces a casting method to strengthen the aluminum alloy cast using high pressure during casting. By using this method, products have a precise metallographic structure. As a result, both the development cost and period were reduced by over the half the time required of the current system and lighter and strong parts were created.

In open-grille vehicle aerodynamics simulation using computational fluid dynamics, in addition to basic flow characteristics, such as turbulent flow with a Reynolds number of several million on the bluff body, it is important to accurately estimate the cooling air flow introduced from the front opening. It is therefore necessary to reproduce the detailed geometry of the entire vehicle including the engine bay as precisely as possible. However, there is a problem of generating a good-quality calculation grid with a small workload. It usually takes several days to a week for the pretreatment process to make the geometry data ‘clean’ or ‘watertight’. The authors proposed a computational method for complex geometries with a hierarchical Cartesian grid and a topology-independent immersed boundary method with dummy cells that discretize the geometry on a cell-by-cell basis and can set an imaginary point arbitrarily.

Over the past several decades, vehicle dynamics have been treated mainly on the basis of linear theories. An actual vehicle, however, also shows nonlinear properties such as roll behavior induced by movement of the roll axis. The purpose of this study was to investigate the vehicle roll dynamics in the nonlinear range. Suspensions were divided into two categories and computer-aided engineering (CAE) was used to conduct analyses of complicated kinematics. The results obtained provided theoretical support for designing the Multi-Link Beam Rear Suspension, a new type of suspension for front-wheel-drive cars.

Automotive electronic control systems have tended to become more complex in recent years as a result of stronger requirements for environmental friendliness and higher levels of driveability. The first step in developing a control system is to study the required logic and system configuration at the initial stage of new vehicle development. The authors have incorporated an engine-vehicle model in a control system CAD program to simulate the logic needed for various control tasks. This paper presents a typical application in which a behavior of some outputs, such as engine torque and acceleration, was analyzed, and the electronic controls needed to assure driveability were identified. The construction and operation of a controller-in-the-loop system are also described.

This paper shows one example of cooling system, optimized by utilizing computer simulation in the early development stage. First, a numerical simulation is conducted to obtain the air flow rate through engine compartment room by the software “STREAM”. Second, ΔTw are calculated by the software “KULI”, developed by Steyr-Daimler-Puch AG, to evaluate the original cooling system. Third, the optimization of this system is conducted by the design of experiment for cost saving and weight reduction. The test value was well matched with the calculated one and CAE was confirmed to be very helpful for saving the proto-build cost and time period.

An expert system has been developed for use in designing exhaust tube layout. Featuring artificial intelligence (AI) techniques, this system is included in our CAD system. It provides designers with information for detecting and correcting design mistakes, based on a body of rules consisting of design standards and accumulated know-how. As a result, it shortens design time and reduces errors. This system is also useful for standardizing design procedures and transmitting techniques accurately. This paper describes the new system and application to exhaust tube layout design. It discusses various problems that must be solved in applying AI techniques to the automobile design process as well as areas and methods of application.

A conventional CAD system is aimed primarily at making the work of creating design drawings more efficient. There are limits, however, to further improvement of design efficiency and design quality with such a system. What is needed is a CAD system that allows design information of various kinds to he compiled for ready access and exchange among designers. To realize a system of this sort, first of all a means was devised of putting into standard format the design information that needs to be included in product design drawings, and of storing this information in a database. These standard drawings are then used in creation of new drawings, by means of an editing process. Moreover, this integrated design database system allows designers to exchange information related to the design work online, in the form of drawing elements.