Search Results

Pulsed nanosecond discharges (PND) can achieve ignition in internal combustion engines through enhanced reaction kinetics as a result of elevated electron energies without the associated increases in translational gas temperature that cause electrode erosion. Atomic oxygen (O), including its electronically excited states, is thought to be a key species in promoting low-temperature ignition. In this paper, high-voltage (17-24 kV peak) PND are examined in oxygen/nitrogen/carbon dioxide/water mixtures at engine-relevant densities (up to 9.1 kg/m3) through pressure-rise calorimetry and direct imaging of excited-state O-atom and molecular nitrogen (N2) in an optically accessible spark calorimeter, with the anode/cathode gap distance set to 5 mm or with an anode-only configuration (DC corona). The conversion efficiency of pulse electrical energy into thermal energy was measured for PND with secondary streamer breakdown (SSB) and similar low-temperature plasmas (LTP) without.

A truck platooning system was tested using two heavy-duty tractor-trailer trucks on a closed test track to investigate the sensitivity of intentional lateral offsets over a range of intervehicle spacings. The fuel consumption for both trucks in the platoon was measured using the SAE J1321 gravimetric procedure while travelling at 65 mph and loaded to a gross weight of 65,000 lb. In addition, the SAE J1939 instantaneous fuel rate was calibrated against the gravimetric measurements and used as proxy for additional analyses. The testing campaign demonstrated the effects of intervehicle gaps, following-vehicle longitudinal control, and manual lateral control. The new results are compared to previous truck-platooning studies to reinforce the value of the new information and demonstrate similarity to past trends. Fuel savings for the following vehicle was observed to exceed 10% at closer following distances.

Detailed exhaust speciation measurements were made on an HCCI engine fueled with iso-octane over a range of fueling rates, and over a range of fuel-stratification levels. Fully premixed fueling was used for the fueling sweep. This sweep extended from a fuel/air equivalence ratio (ϕ) of 0.28, which is sufficiently high to achieve a combustion efficiency of 96%, down to a below-idle fueling rate of ϕ = 0.08, with a combustion efficiency of only 55%. The stratification sweep was conducted at an idle fueling rate, using an 8-hole GDI injector to vary stratification from well-mixed conditions for an early start of injection (SOI) (40°CA) to highly stratified conditions for an SOI well up the compression stroke (325°CA, 35°bTDC-compression). The engine speed was 1200 rpm. At each operating condition, exhaust samples were collected and analyzed by GC-FID for the C1 and C2 hydrocarbon (HC) species and by GC-MS for all other species except formaldehyde and acetaldehyde.

Water injection is a promising technology to improve the fuel efficiency of turbocharged gasoline engines due to the possibility to suppress engine knock. Additionally, this technology is believed to enable the efficient operation of the three-way catalyst also at high-load conditions, through limiting the exhaust temperature. In this numerical study, we investigate the effect of water on the chemical and thermodynamic processes using 3D computational fluid dynamics (CFD) Reynolds-averaged Navier–Stokes (RANS) with detailed chemistry. In the first step, the influence of different amounts of water vapor on ignition delay time, laminar flame speed, and heat capacity is investigated. In the second step, the impact of water vaporization is analyzed for port and direct injection. For this purpose, the water mass flow and the injection pressure are varied.

In light-duty direct-injection (DI) diesel engines, combustion chamber geometry influences the complex interactions between swirl and squish flows, spray-wall interactions, as well as late-cycle mixing. Because of these interactions, piston bowl geometry significantly affects fuel efficiency and emissions behavior. However, due to lack of reliable in-cylinder measurements, the mechanisms responsible for piston-induced changes in engine behavior are not well understood. Non-intrusive, in situ optical measurement techniques are necessary to provide a deeper understanding of the piston geometry effect on in-cylinder processes and to assist in the development of predictive engine simulation models. This study compares two substantially different piston bowls with geometries representative of existing technology: a conventional re-entrant bowl and a stepped-lip bowl. Both pistons are tested in a single-cylinder optical diesel engine under identical boundary conditions.

The fuel energy consumption of subsonic air transportation is examined. The focus is on identification and quantification of fundamental engineering design tradeoffs which drive the design of subsonic tube and wing transport aircraft. The sensitivities of energy efficiency to recent and forecast technology developments are also examined.

Higher compression ratio and turbocharging, with engine downsizing can enable significant gains in fuel economy but require engine operating conditions that cause engine knock under high load. Engine knock can be avoided by supplying higher-octane fuel under such high load conditions. This study builds on previous MIT papers investigating Octane-On-Demand (OOD) to enable a higher efficiency, higher-boost higher compression-ratio engine. The high-octane fuel for OOD can be obtained through On-Board-Separation (OBS) of alcohol blended gasoline. Fuel from the primary fuel tank filled with commercially available gasoline that contains 10% by volume ethanol (E10) is separated by an organic membrane pervaporation process that produces a 30 to 90% ethanol fuel blend for use when high octane is needed. In addition to previous work, this paper combines modeling of the OBS system with passenger car and medium-duty truck fuel consumption and octane requirements for various driving cycles.

A Computational Fluid Dynamics (CFD) study was conducted on four-vehicle platoons, and the aerodynamic data is then coupled with a high-fidelity truck simulation software (TruckSim) to determine fuel efficiency. Previous studies typically have focused on identical two vehicle platoons, whereas this study accounted for more complex platoon configurations. Heavy duty vehicles (HDVs), both military and commercial, make up a significant percentage of fuel consumption. This study aimed to quantify fuel savings of a platoon consisting of dissimilar trucks and trailers, thus reducing vehicle operational cost. The vehicle platoon featured two M915 trucks and two Peterbilt 579 trucks with dissimilar trailer configurations. An unloaded flatbed trailer, a centered 20 ft shipping container, two 20 ft shipping containers, and a 53 ft box trailer configurations were utilized.

Engine-out CO emission and fuel conversion efficiency were measured in a highly-dilute, low-temperature diesel combustion regime over a swirl ratio range of 1.44-7.12 and a wide range of injection timing. At fixed injection timing, an optimal swirl ratio for minimum CO emission and fuel consumption was found. At fixed swirl ratio, CO emission and fuel consumption generally decreased as injection timing was advanced. Moreover, a sudden decrease in CO emission was observed at early injection timings. Multi-dimensional numerical simulations, pressure-based measurements of ignition delay and apparent heat release, estimates of peak flame temperature, imaging of natural combustion luminosity and spray/wall interactions, and Laser Doppler Velocimeter (LDV) measurements of in-cylinder turbulence levels are employed to clarify the sources of the observed behavior.

Platooning heavy-duty trucks decreases aerodynamic drag for following trucks, reducing energy consumption, and increasing both range and mileage. Previous platooning experimentation has demonstrated fuel economy benefits in two-, three-, and four-truck configurations. However, exogenous variables disturb the ability of these platoons to maintain the desired formation, causing an accordion effect within the platoon and reducing energy benefits via acceleration/deceleration events. This phenomenon is increasingly exacerbated as platoon size and road grade variations increase. The current work assesses how platoon size, road curvature, and road grade influence platoon energy efficiency. Fuel consumption rate is experimentally quantified for four heterogeneous Class 8 vehicles operating in standalone (baseline), two-, and four-truck platooning configurations to assess fuel consumption changes while driving through diverse road conditions.

Platooning is a promising technology which can mitigate greenhouse gas impacts and reduce transportation energy consumption. Platooning is a coordinated driving strategy where trucks align themselves in order to realize aerodynamic benefits to reduce required motive force. The aerodynamic benefit is seen as either a “pull” effect experienced by the following vehicles or a “push” effect experienced by the leader. The energy savings magnitude increases nonlinearly as headway (following distance) is reduced [1]. In efforts to maximize energy savings, cooperative adaptive cruise control (CACC) is utilized to maintain relatively short headways. However, when platooning is attempted in the real world, small transient accelerations caused by imperfect control result in observed energy savings being less than expected values. This study analyzes the performance of a recently developed nonlinear model predictive control (NMPC) platooning strategy over challenging terrain.

Due to aerodynamic drag reduction, vehicles may have significant energy savings while platooning in close succession. However, when circumstances force active deceleration to maintain the platoon, such as during vehicle cut-ins or grade changes, the aerodynamic efficiency benefits may be undermined by losses in kinetic energy. In this work, a theoretical relationship is derived to correlate the amount of active deceleration a vehicle experiences with energy efficiency. The derived relationship is leveraged to analyze platooning data from the last vehicle in a class 8 vehicle platoon. The data include both two- and four-truck platoons operating under nine different truck-to-truck gap control strategies. Using J1939 CAN data and GPS-estimated grade profiles, off-throttle data were isolated and longitudinal acceleration is estimated as a function of grade using Kalman filtering.

The fuel efficiency improvement of a prototype Driver-Assistive-Truck-Platooning (DATP) system was evaluated using Computational Fluid Dynamics (CFD). The DATP system uses a combination of radar and GPS, integrated active safety systems, and V2V communications to enable regulation of the longitudinal distance between pairs of trucks without acceleration input from the driver in the following truck(s). The V2V linking of active safety systems and synchronized braking promotes increased safety of close following trucks while improving their fuel economy. Vehicle configuration, speed, and separation distance are considered. The objectives of the CFD analysis are to optimize the target separation distance and to determine the overall drag reduction of the platoon. This reduction directly results in fuel economy gains for all cooperating vehicles.

Lubricant viscosity along the engine cylinder liner varies by an order of magnitude due to local temperature variation and vaporization effects. Tremendous potential exists for fuel economy improvement by optimizing local viscosity variations for specific operating conditions. Methods for analytical estimation of friction and wear in the power-cylinder system are reviewed and used to quantify opportunities for improving mechanical efficiency and fuel economy through lubricant formulation tailored specifically to liner temperature distributions. Temperature dependent variations in kinematic viscosity, density, shear thinning, and lubricant composition are investigated. Models incorporating the modified Reynolds equation were used to estimate friction and wear under the top ring and piston skirt of a typical 11.0 liter diesel engine.

The Organic Rankine Cycle (ORC) has proven to be a promising technology for Waste Heat Recovery (WHR) systems in heavy duty diesel engine applications. However, due to the highly transient heat source, controlling the working fluid flow through the ORC system is a challenge for real time application. With advanced knowledge of the heat source dynamics, there is potential to enhance power optimization from the WHR system through predictive optimal control. This paper proposes a look-ahead control strategy to explore the potential of increased power recovery from a simulated WHR system. In the look-ahead control, the future vehicle speed is predicted utilizing road topography and V2V connectivity. The forecasted vehicle speed is utilized to predict the engine speed and torque, which facilitates estimation of the engine exhaust conditions used in the ORC control model.

Presently, a main mobility sector objective is to reduce its impact on the global greenhouse gas emissions. While there are many techniques being explored, a promising approach to improve fuel economy is to reduce the required energy by using slipstream effects. This study analyzes the demanded engine power and mechanical energy used by heavy-duty trucks during platooning and non-platooning operation to determine the aerodynamic benefits of the slipstream. A series of platooning tests utilizing class 8 semi-trucks platooning via Cooperative Adaptive Cruise Control (CACC) are performed. Comparing the demanded engine power and mechanical energy used reveals the benefits of platooning on the aerodynamic drag while disregarding any potential negative side effects on the engine. However, energy savings were lower than expected in some cases.

Spray modeling is among the main aspects of mixture formation and combustion in internal combustion engines. It plays a major role in pollutant formation and energy efficiency although adequate modeling is still under development. Strong grid dependence is observed in the droplet-based stochastic spray model commonly used. As an alternative, an interactive model called 'SprayLet' is being developed for spray simulations based on one-dimensional integrated equations for the gas and liquid phases, resulting from cross-sectionally averaging of multi-dimensional transport equations to improve statistical convergence. The formulated one-dimensional cross-section averaged system is solved independently of the CFD program to provide source terms for mass, momentum and heat transfer between the gas and liquid phases. The transport processes take place in a given spray cone where the nozzle exit is automatically resolved.

Platooning has produced significant energy savings for vehicles in a controlled environment. However, the impact of real-world disturbances, such as grade and interactions with passenger vehicles, has not been sufficiently characterized. Follower vehicles in a platoon operate with both different aerodynamic drag and different velocity traces than while driving alone. While aerodynamic drag reduction usually dominates the change in energy consumption for platooning vehicles, the dynamics imposed on the follow vehicle by the lead vehicle and exogenous disturbances impacting the platoon can negate aerodynamic energy savings. In this paper, a methodology is proposed to link the change in longitudinal platooning dynamics with the energy consumption of a platoon follower in real time. This is accomplished by subtracting a predicted acceleration from measured longitudinal acceleration.

The NOx emission and knock characteristics of a PFI engine operating on ethanol/gasoline mixtures were assessed at 1500 and 2000 rpm with λ =1 under Wide-Open-Throttle condition. There was no significant charge cooling due to fuel evaporation. The decrease in NOx emission and exhaust temperature could be explained by the change in adiabatic flame temperature of the mixture. The fuel knock resistance improved significantly with the gasohol so that ignition could be timed at a value much closer or at MBT timing. Changing from 0% to 100% ethanol in the fuel, this combustion phasing improvement led to a 20% increase in NIMEP and 8 percentage points in fuel conversion efficiency at 1500 rpm. At 2000 rpm, where knocking was less severe, the improvement was about half (10% increase in NIMEP and 4 percentage points in fuel conversion efficiency).

Accurately predicting real-world vehicle energy consumption is essential for optimizing vehicle designs, enhancing energy efficiency, and developing effective energy management strategies. This paper presents a data-driven approach that utilizes machine learning techniques and a comprehensive dataset of vehicle parameters and environmental factors to create precise energy consumption prediction models. The methodology involves recording real-world vehicle data using data loggers to extract information from the CAN bus systems for ICE and hybrid electric, as well as hydrogen and battery fuel cell vehicles. Data cleaning and cycle-based analysis are employed to process the dataset for accurate energy consumption prediction. This includes cycle detection and analysis using methods from statistics and signal processing, and then pattern recognition based on these metrics.