Search Results

This paper presents a new methodology for the safety assessment of complex software intensive systems such as is envisioned for the coming major upgrade of the air traffic management system known as NextGen. This methodology is based on a new, more inclusive model of accident causation called Systems Theoretic Accident Model and Process (STAMP) [1]. STAMP includes not just the standard component failure mechanisms but also the new ways that software and humans contribute to accidents in complex systems. A new hazard analysis method, called Systems Theoretic Process Analysis (STPA), is built on this theoretical foundation. The STPA is based on systems theory rather than reliability theory; it treats safety as a control problem rather than a failure problem with interactive and possibly nested control loops that may include humans. In this methodology, safety is assured by closed loop control of safety parameters.

The active safety of tractor / trailer-combinations plays an important role in regard to traffic safety in general. For improving the active safety of tractor / trailer-combinations, it is necessary to investigate the interactions between the towing vehicle and the trailer during braking maneuvers. This paper describes the ECE-regulations for the braking force distributions of tractor/full trailer- and tractor / semitrailer-combinations. The influence of different layouts of the braking systems within these regulations on the coupling forces between tractor and trailer and the driving performance of the units during braking is investigated. The dynamical behaviour of a tractor/full-trailer-combination and a tractor / semitrailer-combination are both discussed with the aid of simulations of the ISO-standard testing procedures “Braking in a turn” and “Braking straight ahead”.

This paper reviews the relevant literature on the effects of sulfated ash, phosphorus, and sulfur on DPF, LNT, and SCR catalysts. Exhaust backpressure increase due to DPF ash accumulation, as well as the rate at which ash is consumed from the sump, were the most studied lubricant-derived DPF effects. Based on several studies, a doubling of backpressure can be estimated to occur within 270,000 to 490,000 km when using a 1.0% sulfated ash oil. Postmortem DPF analysis and exhaust gas measurements revealed that approximately 35% to 65% less ash was lost from the sump than was expected based on bulk oil consumption estimates. Despite significant effects from lubricant sulfur and phosphorus, loss of LNT NOX reduction efficiency is dominated by fuel sulfur effects. Phosphorus has been determined to have a mild poisoning effect on SCR catalysts. The extent of the effect that lubricant phosphorus and sulfur have on DOCs remains unclear, however, it appears to be minor.

The aim of this study was to explore if fingernail delamination injury following EMU glove use may be caused by compression-induced blood flow occlusion in the finger. During compression tests, finger blood flow decreased more than 60%, however this occurred more rapidly for finger pad compression (4 N) than for fingertips (10 N). A pressure bulb compression test resulted in 50% and 45% decreased blood flow at 100 mmHg and 200 mmHg, respectively. These results indicate that the finger pad pressure required to articulate stiff gloves is more likely to contribute to injury than the fingertip pressure associated with tight fitting gloves.

Thin sandwich sheets hold a promise for widespread use in automotive industry due to their good crash and formability properties. In this paper, thin stainless steel sandwich sheets with low-density core materials are investigated with regard to their performance in crashworthiness applications. The total thickness of the sandwich materials is about 1.2mm: 0.2mm thick facings and a 0.8mm thick sandwich core. Throughout the crushing of prismatic sandwich profiles, the sandwich facings are bent and stretched while the sandwich core is crushed under shear loading. Thus, a high shear crushing strength of the sandwich core material is beneficial for the overall energy absorption of the sandwich profile. It is shown theoretically that the weight specific shear crushing strength of hexagonal metallic honeycombs is higher than the one of fiber cores - irrespective of their relative density or microstructural geometry.

NASA has long recognized the advantages of providing improved information interfaces to EVA astronauts and has pursued this goal through a number of development programs over the past decade. None of these activities or parallel efforts in industry and academia has so far resulted in the development of an operational system to replace or augment the current extravehicular mobility unit (EMU) Display and Controls Module (DCM) display and cuff checklist. Recent advances in display, communications, and information processing technologies offer exciting new opportunities for EVA information interfaces that can better serve the needs of a variety of NASA missions. Hamilton Sundstrand Space Systems International (HSSSI) has been collaborating with Simon Fraser University and others on the NASA Haughton Mars Project and with researchers at the Massachusetts Institute of Technology (MIT), Boeing, and Symbol Technologies in investigating these possibilities.

Currently, states that are out of compliance with the National Ambient Air Quality Standards must, according to the Clean Air Act Amendments of 1990 (CAAA), develop and implement control strategies that demonstrate specific degrees of reduction in emissions-with the degree of reduction depending upon the severity of the problem. One tool that has been developed to aid regulators in both deciding an appropriate course of action and to demonstrate the desired reductions in mobile emissions is EPA's Mobile 5a emission estimation model. In our study, Mobile 5a has been used to examine the effects of regulatory strategies, as applied to the Northeast United States, on vehicle emissions under worst-case ozone-forming conditions.

A technique has been developed to measure the desorption and subsequent oxidation of fuel in the oil layer by spiking the oil with liquid fuel and firing the engine on gaseous fuel or motoring with air. Experiments suggest that fuel desorption is not diffusion limited above 50 °C and indicated that approximately two to four percent of the cylinder oil layer is fresh oil from the sump. The increase in hydrocarbon emissions is of the order of 100 ppmC1 per 1% liquid fuel introduced into the fresh oil in a methane fired engine at mid-speed and light load conditions. Calculations indicate that fuel desorbing from oil is much more likely to produce hydrocarbon emissions than fuel emerging from crevices.

The engine valve cover is known to be major contributor to powertrain noise due to its large surface area and relatively small thickness. Thus, the acoustic analysis of the valve cover has become one of the key steps in the design process. The present paper describes an acoustic infinite element approach to model the sound radiation of the valve cover. The valve cover bolted to the engine block behaves like a vibrating membrane in an acoustic medium of infinite extent. Typically, the effect of the infinite medium is modeled using either the boundary element method (BEM), or by specifying an equivalent boundary impedance on the terminating surface of an acoustic finite element mesh (NRBC). In this paper, a third method is introduced, wherein the boundary impedances are replaced by acoustic infinite elements. The methodology is presented using two different models. In the first model, a cover with a geometrically simple shape is analyzed.

The expected improved performance of a combined restraint system where an airbag supplements the conventional safety belt was not reflected in reduced g-values on the dummy's chest. However, by the distribution of force over the wider area of the airbag and the corresponding reduction of the specific pressure exerted by the three point belt, improved occupant protection is actually produced. Therefore, measurable quantities other than acceleration should be selected to evaluate the risk of chest injury, such as belt load or chest deflection. A new method to measure the deflection of dummy ribs with strain gauges has been developed. The resulting data indicate a significantly reduced chest deflection when a combined system is used.

The driving simulator is a computer-controlled tool to study the interface between driver and vehicle response under simulated traffic conditions. It permits a controllable, reproducible and cost-effective study of vehicle parameters up to the limits of active safety under non-dangerous conditions. It also permits driver participation in judging vehicle handling characteristics, and in evaluating the ‘feel’ of the steering, suspension, braking, and drive train, including the driver's environment, beginning with the initial vehicle design stages. The paper will describe fully the concept, design and planned activities as well as report on the new possibilities of using the driving simulator as a research and development tool.

Daimler-Benz considers safety belts as the fundamental and essential restraining system. The company began offering a Supplemental Restraint System option consisting of a driver airbag system and an emergency tensioning belt retractor for the passenger in December 1980. The functional reliability of the system has proven satisfactory.

Information on the driving stability can be obtained in the form of oversteer or understeer tendencies and acceleration limits on a circular path. Up to now the calculations have only been made on an ideal, even roadway. Significant dynamic characteristics, such as the tuning of the shock absorbers, which also play a role in evaluating the stability of a vehicle in a driving test, are thereby not included in the calculations. In this paper the unevenness of the roadway is taken into consideration in calculating steady state cornering tests. Different vehicle models can be evaluated in regard to their handling or active safety with the aid of the driver's steering actions required to keep the car on course.

In order to reduce the severity of injuries to pedestrians and cyclists, the sheetmetal contact zones of Mercedes-Benz cars are constructed of a yielding, smooth-surfaced design. Unfortunately, contradictory demands are made on some components. This is particularly true for the bumper in which avoiding or reducing the cost of repair requires a greater bumper height, overhang, and stiffness, which run counter to the requirements of pedestrian protection. Despite this conflict, however, the bumpers of recently developed Mercedes-Benz cars offer a high degree of pedestrian protection since they are faced with rigid foam. To assist in both mathematical and experimental pedestrian impact simulation, standard test dummies should be modified by reducing the stiffness at the waist in order to achieve a higher degree of faithfulness to human behaviour.

Safety considerations at Daimler-Benz are based on real-world accidents from which internal test procedures are derived. The example of the frontal collision is a clear illustration of this. In a crash against a flat, full car width barrier, a rare occurrence in real-world accidents, the impact energy is distributed over the entire width of the car. The majority of real-world frontal crashes, however, involve only partial overlap of the front. An adequately designed structure has to absorb the crash energy before it deforms the passenger compartment, i. e. by distributing the impact forces, and strategically located components must avoid the formation of blocks. In particular, the passenger compartment must be sufficiently stiff. Restraint systems and interior padding can only serve their protective purpose to their fullest if the survival space for the occupants is maintained intact.

Daimler-Benz have developed an automatically/electronically controlled traction system, the 4MATIC. Great store has been set by active safety. This paper deals with the problems involved in 4-Wheel drive and analyzes the reasons which led to the 4MATIC concept. Depending on the conditions encountered, the drive components engage automatically one after the other in the sequence front-wheel drive - interaxle differential lock - rear axle differential lock. The engagement, and thus the approaching limits of driving dynamics, is indicated to the driver by an indicator lamp so that he can adjust to the deteriorated conditions in time. A further important advantage of this system is the automatic disengagement of the differential locks when braking so that the anti-lock braking remains fully effective.

This report deals with the development and use of the Daimler-Benz Isohuman Simulation Model for the mathematical simulation of dummy behaviour in an impact environment. Designated ISM, this computer program package is capable of handling both automobile occupant and pedestrian kinematics. Daimler-Benz safety engineers use the ISM to evaluate new safety designs before performing actual laboratory tests. The ISM code uses the theoretical algorithm of Prof. Wittenburg. The dummy is represented by 11 rigid body elements. Realistic and accurate simulations are assured by the fact that a considerable number of functional and sophisticated algorithms were developed to involve the different interactions of dummy-to-belt or dummy-to-vehicle. In particular, considerable work is being done to introduce a more precise and realistic dummy and vehicle geometry.

Distribution of load has a major influence on type and severity of chest injuries. The introduction of the Hybrid III dummy into crash testing along with the requirement to measure sternum deflection for injury assessment has brought about the need to evaluate how well its thorax senses various loading conditions. Tests revealed that different load distributions, i.e. due to a diagonal shoulder belt or an airbag, did not produce the expected chest deflection patterns. This appears to be the result of both a relatively stiff sternum assembly and a nonsuitable design of the clavicle. Chest compression responses became more realistically when both, sternum and clavicle of the Hybrid II were mounted into the Hybrid Ill's thorax. As a consequence, this study suggests that the thorax of the Hybrid III dummy must be improved.

The risk of head or chest injuries is usually evaluated by means of acceleration measurements using a dummy. Unfortunately, this data provides no information on load distribution over the contact areas which is often related to localized fractures of the bony structure. Therefore, new methods of measuring local forces were developed. 1. Pressure indicating devices attached to a dummy's face are capable of monitoring the local pressure during impact; foil's color change is interpreted by means of digital image analysis. 2. A velocity sensitive viscous tolerance criterion was calculated from the chest compression response of a dummy instrumented with strain gauges on the ribs. The application of advanced techniques in laboratory tests clearly supports the experience of improved protection potential through the use of airbag systems.

A human-centered systems analysis was applied to the adverse aircraft weather encounter problem in order to identify desirable functions of weather and icing information. The importance of contingency planning was identified as emerging from a system safety design methodology as well as from results of other aviation decision-making studies. The relationship between contingency planning support and information on regions clear of adverse weather was investigated in a scenario-based analysis. A rapid prototype example of the key elements in the depiction of icing conditions was developed in a case study, and the implications for the components of the icing information system were articulated.