Search Results

A compact and high performance electric motor, called the 3D motor and designed to achieve output torque density of 100 Nm/L, was developed for use on electric vehicles and hybrid electric vehicles. The motor adopts an axial flux configuration, consisting of a disk-shaped stator sandwiched between two disk-shaped rotors with permanent magnets. It also adopts 9-phase current with a fractional slot combination, both of which increase the torque density. The rated torque output of this high power-density motor is achieved by applying a hybrid cooling system comprising a water jacket on the outer case of the stator and oil dispersion into the air gaps. The mechanical strength of the rotors against centrifugal force and that of the stator against torque exertion were confirmed in mechanical experiments. Several measures such as flux barriers, a chamfered rotor rim, parallel windings, and radially laminated cores were adopted to suppress losses.

Detergent additives in automotive gasoline fuel are mainly designed to reduce deposit formation on intake valves and fuel injectors, but it has been reported that some additives may contribute to CCD formation. Therefore, a standardized bench engine test method for CCDs needs to be developed in response to industry demands. Cooperative research between the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association, Inc. (JAMA), has led to the development of a 2.2L Honda engine dynamometer-based CCD test procedure to evaluate CCDs from fuel additives. Ten automobile manufacturers, nine petroleum companies and the Petroleum Energy Center joined the project, which underwent PAJ-JAMA round robin testing. This paper describes the CCD test development activities, which include the selection of an engine and the determination of the optimum test conditions and other test criteria.

This paper describes simultaneous attainment in improving fuel consumption, output power and reducing HC emissions with a direct injection S.I. engine newly developed in Nissan. Straight intake port is adopted to increase discharge coefficient under WOT operation and horizontal swirl flow is generated by a swirl control valve to provide stable stratified charge combustion under part load conditions. As a result, fuel consumption is reduced by more than 20% and power output is improved by approximately 10%. Moreover, unburned HC is reduced by equivalently 30% in engine cold start condition. An application of diagnostic and numerical simulation tools to investigate and optimize various factors are also introduced.

The demands on valve seat insert materials, in terms of providing greater wear-resistance at higher temperatures, enhanced machinability and using non-environmentally hazardous materials at a reasonably low cost have intensified in recent years. Due therefore to these strong demands in the market, research was made into the possibility of producing a new valve seat insert material. As a result a high speed steel based new improved material was developed, which satisfies the necessary required demands and the evaluation trials, using actual gasoline engine endurance tests, were found to be very successful.

The SR engine is a new medium-size, all aluminum (cylinder block, head, rocker cover and oil pan) in-line 4-cylinder gasoline powerplant developed as a replacement for CA engine in Nissan's compact passenger cars. The development aim set for this engine was to achieve excellent power output and ample torque in the middle-and high-speed ranges, as well as a clear, linear engine sound up to the red zone. These performance targets have been achieved through the use of the 4-valve-per-cylinder DOHC design featuring a Y-shaped valve rocker arm system. This system allows a straight intake port for high power output and a narrow valve angle for a compact combustion chamber. The result is ample torque output as well as good fuel economy.

A variable swirl intake port system for 4 valves/cylinder direct injection diesel engines was developed. This system combines two mutually independent intake ports, one of which is a helical port for generating an ultra-high swirl ratio and the other is a tangential port for generating a low swirl ratio. The tangential port incorporates a swirl control valve that controls the swirl ratio by varying the flow rate. To investigate the performance of the intake port system, steady-state flow tests were conducted in parallel with three-dimensional computations. In conducting the steady-state flow tests, it was found that a paddle wheel flow sensor was not suitable for evaluating the characteristics of the high-swirl port and that it was necessary to use an impulse swirl flow meter.

This paper describes the new VK56VD engine, which was developed in response to growing demand for cleaner automobiles, better fuel economy, and improved engine performance. A 5.6 L V8 engine, the VK56VD will go into the new Infiniti M56 premium sport luxury sedan. To boost power and efficiency and lessen its environmental impact, this engine will utilize key technologies such as Continuous Variable Valve Event and Lift (VVEL) and Direct Injection Gasoline (DIG). Details of the VK56VD are presented here along with highlights of the applied technologies and the development means.

Every fuel injection system for DI gasoline engines has a DC-DC converter to provide high, stabile voltage for opening the injector valve more quickly. A current control circuit for holding the valve open is also needed, as well as a large-capacity capacitor for pilot injection. Since these components occupy considerable space, an injector drive unit separate from the ECU must be used. Thus, there has been a need for a fuel injection system that can inject a small volume of fuel without requiring high voltage. To meet that need, we have developed a dual coil injector and an opening coil current control system. An investigation was also made of all the factors related to the dynamic range of the injector, including static flow rate, fuel pressure, battery voltage and harness resistance. Both efforts have led to the adoption of a battery voltage-driven fuel injector.

This paper describes the motor and inverter system developed for the Nissan LEAF that has been specifically designed as a mass-produced electric vehicle. The system produces maximum torque of 280 Nm and maximum power of 80 kW. The motor achieves a small size, high power, and high efficiency as a result of adopting the following in-house technologies. The magnetic circuit design was optimized for an interior magnet synchronous motor to attain the maximum performance figures noted here. The material technologies of the rotor and the stator facilitate high efficiency and the production technology achieves high density winding. The cooling mechanism is optimally designed for a mass-produced electric vehicle. The inverter incorporates the following original technologies and application-specific parts to obtain cost reductions combined with reliability improvements. The power module has an original structure with the power devices mounted directly on the busbars.

Valve deposits in gasoline engines increase with time, absorbing fuel during acceleration and releasing fuel during deceleration. Valve deposits insulate the heat release from the cylinder and this phenomenon is the cause of bad fuel vaporization. In this way, the deposits greatly affect the driveability and exhaust emissions. Using a 3.OL MPI(Multipoint Injection) engine, we measured the quantity of fuel that deposits at the intake port, and the throttle response (using a wall-flow meter made by Nissan Motor Co.1), 2) to study the deposits effect on driveability and exhaust emissions at a low temperature. The deposits were formed on the intake valve surface (about 8.0 on the CRC deposit rating scale) through 200 hours of laboratory engine stand operation. At low temperature, C9 and C10 hydrocarbons tend to stick to the intake port surface and intake valve as “wall-flow”; this is one cause of bad driveability.

A new high-performance and lightweight TiA1 intermetallic compound exhaust valve has been developed. The TiA1 valve can improve power output and fuel economy by contributing higher engine speeds and a reduction in valvetrain friction. It was achieved by developing a Ti-33.5A1-0.5Si-1Nb-0.5Cr (mass%) intermetallic compound, a precision casting method for TiA1 that provides a low-cost, high-quality process, and a plasma carburizing technique for assuring good wear resistance on the valve stem end, stem and face.

The geometry and area of the notch in the swirl control valve installed in the intake port were varied to analyze the effects on HC emissions. A swirl control valve functions to promote the formation of a homogeneous mixture, enabling the amount of liquid fuel supplied to the cylinder to be reduced. For this reason, it is difficult to obtain an added effect through the combined use of a swirl control valve and an auxiliary-air type of injector for assisting fuel atomization. Tumble (vertical swirl) flow fields are effective in shortening the combustion period. This results in a higher exhaust gas temperature at an equivalent level of combustion stability. It was thought that swirl flow fields produce residual gas flow in the cylinder after the completion of the main combustion period. It is surmised that the residual gas flow functions to diffuse and promote after-burning of the unburned HC layer.

An electronically controlled closed-loop carburetor system has been developed. This system's air-fuel ratio control is characterized by the air bleeds being controlled by turning the solenoid valves on and off at a constant frequency. The frequency above 30 Hz was desirable for practical performances. Some improvements and developments were made to the carburetor, the solenoid valve and the control unit. In application of this system to a three-way catalytic system with O2 sensor, the emissions met the 1978 Japanese standards.

Judging from viewpoint of automotive safety and more space by eliminating a spare tire, the development of the run-flat tires is important. Many problems relating to weight increase and usability had to be solved in the course of the development of such tires. The “ N ” type run-flat tire, described in this paper, has a simple structure with reinforced side walls and additional beads to fit the rim flanges. Though this tire system brought about a small amount of weight increase, it needs no special part, therefore the conventional road wheels, air valves and tire changers may be used. We have tested and evaluated this tire system equipped with passenger cars as well as on the test machines. Especially vehicle dynamics such as steering, stability and so forth were tested. The test results indicated that this tire system is practical enough.

This Paper describes a computer-controlled power steering system that has been developed and applied to production vehicles. The system provides full power assist at parking speeds, and gradually decreases assistance with increasing vehicle speed to give a normal unassisted “road feel” at highway speeds. The system enables a driver to choose one assistance characteristic among three choices at the flick of a switch, according to the driver's preference and road conditions. A solenoid-operated bypass valve is used to reduce the hydraulic fluid supply to the steering gear, which results in a heavier steering effort. The most suitable valve characteristic curve which corresponds to the increased pressure in the system due to the applied torque is discussed in this study. It is shown that detection of the velocity of steering wheel rotation and extension of the range of characteristics possible are effective ways to ensure good control over the power assistance.

Nissan has developed a second generation ceramic turbocharger rotor which provides greater reliability and higher performance than a conventional ceramic rotor. The new rotor is made of silicon nitride, which has demonstrated sufficient strength in vehicle applications. The bonding technique for joining the ceramic rotor to the metal shaft has been confirmed through experimentation to have sufficient reliability. The second generation rotor is featured by the low stress design and higher dynamic strength, and two factors contribute to its higher reliability. The rotor shape was optimized on the basis of results obtained in two analyses of particle impact resistance and applied combined stress. Test results show that the reliability of the second generation rotor have been substantially improved over those of the conventional rotor now being used on production vehicles.

Development of a high strength valve spring for automotive engines achieves higher power output and better fuel economy. New material which consists of finely structure and subjected to advanced shot peening, has been developed. Stress analysis of the valve spring moving edge, using the finite element method, has been done for effective application. The merits of this new spring have been confirmed by engine experiments.

Turbocharged engines exhibit poor transient response, especially when accelerating from low speeds at low loads, due to the inertia of the turbocharger rotating mechanism. In looking for ways to overcome this disadvantage, we investigated the possibilities of variable geometry turbochargers, and evaluated the performance characteristics of several types. We decided on the single flap type, and established a control method using compressor outlet pressure to control the flap and waste gate valves. Based on the results of experiments with this method, we developed an electronic pressure feedback system which greatly improves transient engine response and, at the same time, engine performance over a wide range of engine speeds.

Nissan utilizes ceramics in the turbine rotor of turbochargers to improve acceleration response by reducing the inertia weight of the turbine rotor. Since ceramic material does not yield, a high degree of localized stress will cause it to fail. Therefore, in order to be able to apply this brittle material to a high-speed rotor under high-stress conditions, silicon nitride material has been improved, and a low-stress shape employing the three-dimensional finite element method developed. Furthermore, a new technique for bonding the ceramic rotor to a metal shaft is employed in order to reduce residual stress caused by the difference in thermal expansion coefficients between the ceramic and metal materials. Since the strength of ceramics varies widely, it was necessary to confirm the reliability of the ceramic rotor and evaluate its life of fatigue. This paper, then, describes the design philosophy, bonding method, reliability and durability of the ceramic rotor.

Since a 4-valve engine is less flexible in the design and location of the intake ports as compared with a conventional 2-valve engine, there are some difficulties in strengthening the air motion, including swirl and turbulence, in order to achieve stable combustion under lean mixture operation. This study examined air motion imporvements of 4-valve engine that result in a stable combustion with a lean mixture. These improvements are brought about by the installation of a swirl control valve in each intake port. The results of this study have clarified that the lean stable limit was extended from an air-fuel ratio of 21.5 to 26.3 under a partial load, by optimizing the location and diameter of aperture of the swirl control valve.