Search Results

Partially Premixed Combustion (PPC) is a combustion concept which aims to provide combustion with low smoke and NOx with high thermal efficiency. Extending the ignition delay to enhance the premixing, avoiding spray-driven combustion and controlling the combustion temperature at an optimum level through use of suitable lambda and EGR levels have been recognized as key factors to achieve such a combustion. Fuels with high ignitability resistance have been proven to be a useful to extend the ignition delay. In this work pure ethanol has been used as a PPC fuel. The objective of this research was initially to investigate the required operating conditions for PPC with ethanol. Additionally, a sensitivity analysis was performed to understand how the required parameters for ethanol PPC such as lambda, EGR rate, injection pressure and inlet temperature influence the combustion in terms of controllability, stability, emissions (i.e.

In the automotive industry, the piezo-based in-cylinder pressure sensor is getting commercialized and used in production vehicles. For example, the pressure sensor offers the opportunity to design algorithms for estimation of engine emissions, such as soot and NO , during a combustion cycle. In this paper a zero-dimensional NO model for a diesel engine is implemented that will be used in real time. The model is based on the thermal NO formation and the Zeldovich mechanism using two non-geometrical zones: burned and unburned zone. The influence of EGR on combustion temperature was modeled using a well-known thermodynamic identity where specific heat at constant pressure is included. Specific heat will vary with temperature and the gas composition. The model was implemented in LabVIEW using tools specific for an FPGA (Field-Programmable Gate Array).

A diesel engine developed for an international market must be able to run on different fuels considering the diesel fuel qualities and the increasing selection of biofuels in the world. This leads to the question of how different fuels perform relative to a standard diesel fuel when not changing the hardware settings. In this study five fuels (Japanese diesel, MK3, EN590 with 10% RME, EN590 with 30% RME and pure RME) have been compared to a reference diesel fuel (Swedish MK1) when run on three different speeds and three different loads at each speed. The experiments are run on a Scania 13l Euro5 engine with standard settings for Swedish MK1 diesel. In general the differences were not large between the fuels. NO x usually increased compared to MK1 and then soot decreased as would be expected. The combustion efficiency increased with increased RME contents of the fuel but the indicated efficiency was not influenced by RME except for at higher loads.

In-cylinder flow measurements, conventional swirl measurements and CFD-simulations have been performed and then compared. The engine studied is a single cylinder version of a Scania D12 that represents a modern heavy-duty truck size engine. Bowditch type optical access and flat piston is used. The cylinder head was also measured in a steady-flow impulse torque swirl meter. From the two-dimensional flow-field, which was measured in the interval from -200° ATDC to 65° ATDC at two different positions from the cylinder head, calculations of the vorticity, turbulence and swirl were made. A maximum in swirl occurs at about 50° before TDC while the maximum vorticity and turbulence occurs somewhat later during the compression stroke. The swirl centre is also seen moving around and it does not coincide with the geometrical centre of the cylinder. The simulated flow-field shows similar behaviour as that seen in the measurements.

In one dimensional engine simulation software, flow losses over complex geometries such as valves and ports are described using flow coefficients. It is generally assumed that the pressure ratio over the valve has a negligible influence on the flow coefficient. However during the exhaust valve opening the pressure difference between cylinder and port is large which questions the accuracy of this assumption. In this work the influence of pressure ratio on the exhaust valve flow coefficient has been investigated experimentally in a steady-flow test bench. Two cylinder heads, designated A and B, from a Heavy-Duty engine with different valve shapes and valve seat angles have been investigated. The tests were performed with both exhaust valves open and with only one of the two exhaust valves open. The pressure ratio over the exhaust port was varied from 1.1:1 to 5:1. For case A1 with a single exhaust valve open, the flow coefficient decreased significantly with pressure ratio.

The effect of blockage due to the presence of the wind tunnel walls has been known since the early days of wind tunnel testing. Today there are several blockage correction methods available for correcting the measured aerodynamic drag. Due to the shape of the test object, test conditions and wind tunnel dimensions the effect on the flow may be different for two cab variants. This will result in a difference in the drag delta between so-called open-road conditions and the wind tunnel. This makes it more difficult to evaluate the performance of two different test objects when they are both tested in a wind tunnel and simulated in CFD. A numerical study where two different cab shapes were compared in both open road condition, and in a digital wind tunnel environment was performed.

Flow reversal chambers are common design elements in mufflers. Here an idealized flow reversal chamber with large cross-section but small depth has been studied. The inlet and outlet ducts as well as the cross-sectional area are fixed while the depth of the chamber can be varied. The resulting systems are then characterized experimentally using the two-microphone wave decomposition method and compared with results from both finite element modeling and various approaches using two-port elements. The finite element modeling results are in excellent agreement with the measurements over the whole frequency range studied, while two-port modeling can be used with engineering precision in the low frequency range. The influence of mean flow was studied experimentally and was shown to have relatively small influence, mainly adding some additional losses at low frequencies.

Typically, the combustion in an internal combustion engine is open-loop controlled. The introduction of a cylinder pressure sensor opens the possibility to introduce a virtual combustion sensor. This virtual sensor is a possible enabler for closed-loop combustion control and thus the possibility to counteract the effects of engine part to part variation, component ageing and fuel quality diversity. The extent to which these effects can be counteracted is determined by the detection limits of the virtual combustion sensor. To determine the limitation of the virtual combustion sensor, a virtual combustion sensor system was implemented based on a one-zone heat-release analysis, including the signal processing of the pressure sensor input. The typical error sources in a heavy-duty engine were identified and quantified. The virtual combustion sensor system was presented with flawed signals and the sensor’s sensitivities to the errors were quantified.

The emission control in heavy-duty vehicles today is based on predefined injection strategies and after-treatment systems such as SCR (selective catalytic reduction) and DPF (diesel particulate filter). State-of-the-art engine control is presently based on cycle-to-cycle resolution. The introduction of the crank angle resolved pressure measurement, from a piezo-based pressure sensor, enables the possibility to control the fuel injection based on combustion feedback while the combustion is occurring. In this paper a study is presented on the possibility to control NOx (nitrogen oxides) formation with a crank angle resolved NOx estimator as feedback. The estimator and the injection control are implemented on an FPGA (Field-Programmable Gate Array) to manage the inherent time constraints. The FPGA is integrated with the rest of the engine control system for injection control and measurement.

After-oxidation in Heavy Duty (HD) diesel combustion is of paramount importance for emissions out from the engine. During diffusion diesel combustion, lots of particulate matter (PM) is created. Most of the PM are combusted during the after-oxidation part of the combustion. Still some of the PM is not, especially during an engine transient at low lambda. To enhance the PM oxidation in the late engine cycle, swirl together with high injection pressure can be implemented to increase in-cylinder turbulence at different stages in the cycle. Historically swirl is known to reduce soot particulates. It has also been shown, that with today's high injection pressures, can be combined with swirl to reduce PM at an, for example, engine transient. The mechanism why the PM engine out is reduced also at high injection pressures is however not so well understood.

In-cylinder flow pattern has been examined experimentally in a heavy duty optical diesel engine and simulated with CFD code during the combustion and the post-oxidation phase. Mean swirling velocity field and its evolution were extracted from optical tests with combustion image velocimetry (CIV). It is known that the post-oxidation period has great impact on the soot emissions. Lately it has been shown in swirling combustion systems with high injection pressures, that the remaining swirling vortex in the post-oxidation phase deviates strongly from solid body rotation. Solid body rotation can only be assumed to be the case before fuel injection. In the studied cases the tangential velocity is higher in the centre of the piston bowl compared to the outer region of the bowl. The used CIV method is closely related to the PIV technique, but makes it possible to extract flow pattern during combustion at full load in an optical diesel engine.

Energy dissipation due to micro-slip in joints is the primary source of damping in many vehicle and space structures. This paper presents results on how the surface topology may be modified to increase the energy dissipation in joints. An analytical solution for general forms of contact pressure of a one-dimensional micro-slip problem is presented. The solution indicates how the contact pressure should be distributed to maximize the energy dissipation. Two dimensional contact pressures are optimized using finite element methods in combination with numerical optimization methods and the results are used to modify the surface topology in bolted joints in order to increase the energy dissipation during loading. The predicted increase of energy dissipation is validated with physical testing. A direct result of the study is a washer with varying thickness increasing the energy dissipation in joints and hence the structural damping of joined structures.

Planetary gears in heavy truck gearboxes are normally manufactured by forging a blank, turning, hobbing, shaving and heat-treatment followed by grinding. Due to the size of the gear the net shape capability of PM methods can be cost effective alternatively to conventional manufacturing. Warm compaction and surface densification are two PM methods to reach high density and thereby high strength and fatigue properties. Typical characteristics for PM gears manufactured by these methods are outlined.

In this work, the effect of swirl to tumble ratio on homogeneity, turbulence and mixing in a generic heavy duty Diesel engine during compression, is investigated using Large-Eddy Simulations. The main conclusion is that the relative importance of dilatation (relative volume change) increases whereas the effect of tumble breakdown decreases with the swirl to tumble ratio. In detail, we show that an increase in tumble raises the peak turbulence level and shifts the peak to earlier crank angles, which in turn leads to higher dissipation. Moreover, maximum turbulence level at top dead center is obtained for a combination of swirl and tumble rather than for pure tumble. Furthermore, it is observed that the peak turbulent kinetic energy displays levels three times greater than the initial kinetic energy of the tumble motion. Thus, energy is added to the flow (turbulence) by the piston through generation of vorticity by vorticity-dilatation interaction.

There is a need for reducing fuel consumption and thereby also reducing CO2 and other emissions in all areas of transportation and the forest industry is no exception. In the particular case of timber trucks special care have to be taken when designing such vehicles; they have to be sturdy and operate in harsh conditions and they are being driven empty half the time. It is well known that the aerodynamic resistance constitutes a significant part of the vehicles driving resistance and four areas in particular, front of vehicle, gap, side/underbody and rear of the vehicle contributes about one quarter each. In order to address these issues a wind tunnel investigation was initiated where a 1:6 scale model of a timber truck was designed to operate in a 3.6 m wind tunnel. The present model resembles a generic timber truck with a flexible design such that different configurations could be tested easily.

A method developed in SAE 2019-01-0058 to correct for deviations from quasi-steady exhaust valve flow is implemented on a single-cylinder GT-Power model and the effects on pumping work and blowdown pulse characteristics are investigated. The valve flow area is always reduced compared to the reference quasi-steady case. It decreases with higher pressure ratios over the valve and increases with higher engines speeds. The reduced flow area increases pumping work with load and engine speed, though primarily with engine speed. The magnitude of the blowdown pulse is reduced and the peak is shifted to a later crank angle.

Factors influencing pilot-injection combustion were investigated using heat release analysis in a heavy-duty diesel engine fuelled with standard diesel fuel. Combinations of pilot-injection parameters i.e. pilot start of injection, pilot mass, pilot-main injection separation, and rail pressure were studied for various operating conditions and combustion phases. An experiment was designed to investigate the factors influencing the combustion of the pilot. For improved injected fuel-mass accuracy, reference data for the injectors were measured in a spray rig prior to the engine experiments. Results show that cycle-to-cycle variations and cylinder-to-cylinder variations influence pilot autoignition and the amount of heat released. Rail pressure and injected pilot mass affect the obtained variance depending on the chamber conditions. The obtained combustion modes (premixed, diffusive) of pilot combustion were found to be a function of the injected mass and rail pressure.

Typically the combustion in a direct injected compression ignited internal combustion engine is open-loop controlled. The introduction of a cylinder pressure sensor opens up the possibility of a virtual combustion sensor which could enable closed-loop combustion control and thus the potential to counteract effects such as engine part to part variation, component ageing and fuel quality diversity. Closed-loop combustion control requires precise, robust and preferably cheap sensors. This paper presents a virtual cylinder pressure sensor based on the signal from the inexpensive but well proven knock sensor. The method used to convert the knock sensor signal into a pressure estimate included the stages: Phase correcting the raw signal, Filtering the raw signal, Scaling the signal to known thermodynamic laws and provided engine sensors signals and Reconstructing parts of the signal with other known models and assumptions.