Search Results

A great deal of interest is focused on Homogeneous Charge Compression Ignition (HCCI) combustion today as a combustion system enabling internal combustion engines to attain higher efficiency and cleaner exhaust emissions. Because the air-fuel mixture is compression-ignited in an HCCI engine, control of the ignition timing is a key issue. Additionally, because the mixture ignites simultaneously at multiple locations in the combustion chamber, it is necessary to control the resultant rapid combustion, especially in the high-load region. Supercharging can be cited as one approach that is effective in facilitating high-load operation of HCCI engines. Supercharging increases the intake air quantity to increase the heat capacity of the working gas, thereby lowering the combustion temperature for injection of the same quantity of fuel. In this study, experiments were conducted to investigate the effects of supercharging on combustion characteristics in an HCCI engine.

On a bluff body which has a slant surface on the rear upper part, it is well known that the drastic change of a wake structure behind the rear body occurs at 30°of the slant angle. Originally, this critical phenomenon was pointed out by L.J. Janssen, W.H. Hucho, and H.J. Emmelmann in the middle of the 1970s. In 1984, S.R. Ahmed conducted systematic measurements by changing the rear slant angle of the bluff body, called the “Ahmed Body”, to find the critical phenomenon. In the 2000s, D.B. Sims-Williams found that the Ahmed Body had vortex structures which had specific frequencies. However, the relationship between the critical phenomenon and the unsteady behaviour has not been clarified yet. Therefore, as the first step of this study, we measured the unsteady wake behaviour for various slant angles to find the relationship between the Strouhal number and the angle. The characteristics of the fluctuation were captured with two hot-wires.

An air-dam spoiler is commonly used to reduce aerodynamic drag in production vehicles. However, it inexplicably tends to show different performances between wind tunnel and coast-down tests. Neither the reason nor the mechanism has been clarified. We previously reported that an air-dam spoiler contributed to a change in the wake structure behind a vehicle. In this study, to clarify the mechanism, we investigated the coefficient of aerodynamic drag CD reduction effect, wake structure, and underflow under different boundary layer conditions by conducting wind tunnel tests with a rolling road system and constant speed on-road tests. We found that the air-dam spoiler changed the wake structure by deceleration of the underflow under stationary floor conditions. Accordingly, the base pressure was recovered by approximately 30% and, the CD value reduction effect was approximately 10%.

A simulation framework for vehicle aerodynamics using up to 10 billion fully unstructured cells has been developed on a world-fastest class supercomputer, called the K computer, in Kobe, Japan. The simulation software FrontFlow/red-Aero was fully optimized on the K computer to utilize up to 10,000 processors with tens of thousands of cores. A hybrid parallelization method using MPI among processors and OpenMP among cores inside each processor was adopted. The code was specially tuned for unsteady aerodynamic simulation including large-eddy simulation, and low Mach number approximation was adopted to avoid excessive iterations usually required for the fully incompressible algorithm. The automated mesh refining system was developed to generate unstructured meshes of up to 10 billion cells. In the system, users only generate unstructured meshes in the order of tens of millions of cells directly using commercial preprocessing software.

Primary work is to investigate premixed laminar flame propagation in a constant volume chamber of iso-octane/air combustion. Experimental and numerical results are investigated by comparing flame front displacements under lean to rich conditions. As the laminar flame depends on equivalence ratio, temperature, and pressure conditions, it is a main property for chemical reaction mechanism validation. Firstly, one-dimensional laminar flame burning velocities are predicted in order to validate a reduced chemical reaction mechanism. A set of laminar burning velocities with pressure, temperature, and mixture equivalence ratio dependences are combined into a 3D-CFD calculation to compare the predicted flame front displacements with that of experiments. It is found that the reaction mechanism is well validated under the coupled 1D-3D combustion calculations. Next, lean experiments are operated in a SI engine by boosting intake pressure to maintain high efficiency without output power penalty.

In recent years, one of the most important issues in the automotive industry is the improvement of fuel economy started from the environmental problem. Making cars lighter and reducing the coefficient of friction are two ways to improve fuel economy. Reducing the weight of a cylinder, an engine component, is a typical example. The traditional, mainstream method to reduce cylinder weight has been to convert cast iron cylinder blocks into aluminum cylinder blocks by using cast iron sleeves. To further make engines lighter and more compact, however, it is desirable that cast iron sleeves be abolished, or, in other words, making cylinder blocks sleeveless. A typical technology to make cylinder blocks sleeveless is applying anti- wear coating on a bore wall. Electroplating is currently the mainstream method used for this technology. It must be noted, however, electroplating is used primarily for low-pressure cast cylinders.

An on-line oil consumption measurement system using the SO2 tracer method has characterized automotive gasoline engine oil consumption under various engine operating conditions, including a 200-hour durability test. An oil consumption map of total engine, individual cylinder, and valve train was produced for various speed and load ranges under both steady-state and step-transient operating conditions. The effect of spark timing as an additional engine parameter on the oil consumption was also investigated. Oil consumption maps have enlightened the conventional understanding of oil consumption characteristics and broadened the areas of concern for control technologies. This paper reports the benefit of the on-line oil consumption measurement system, the result of oil consumption history over the durability test, discrete measurement of oil consumption contribution within the engine, and various oil consumption characteristics affected by engine operating conditions.

The flow vector variations at the transfer port exit in a small two-stroke engine under firing condition were investigated experimentally. A fiber LDV system was used to measure the two-dimensional velocities near the cylinder to obtain the scavenging flow vector. The scavenging flow vector variations at different engine speeds were discussed, and the relation between its vector behavior and the pressure differences between the exhaust pipe and the crankcase was examined. The measurement results show that the velocity profiles at the scavenging port were not uniform and to obtain the representative velocity at the port exit was impossible. But the major features of the scavenging flow can be understood from the pressure difference between the exhaust pipe and the crankcase. The start timing of the scavenging flow was delayed due to the residual gas and high pressure in the cylinder when the scavenging port was opened.

The aerodynamic performance of new vehicles is commonly determined using computational fluid dynamics (CFD) and wind tunnel tests. The final assessment is carried out by actual running tests. In particular, ideas regarding fuel consumption improvement that relate to components for the reduction of the coefficient of drag (CD) value are evaluated by coast-down tests. However, a difference often exists between the component's efficiency between wind tunnel tests and coast-down tests. Therefore, we focused on the efficiency of an air-dam spoiler in reducing CD values. A comparison was made between the aerodynamic effect of the air-dam spoiler in wind tunnel and coast-down tests in terms of the CD value and the wake structure behind the vehicle. To determine the relationship between the CD value and the wake structure behind the vehicle, we measured vehicle speed, wind velocity and direction, vehicle height, and pressure distribution on the back door.

The critical change in drag occurring on the Ahmed body when the slanted base has an angle of 30° is due to a transition in the wake structure. In a previous study on flow analysis across the Ahmed body, we investigated the unsteady wake experimentally using hot-wire and particle image velocimetry measurements. However, because the experimental analysis yielded limited data, the spatially unsteady wake behaviour, interaction between the trailing vortex and transverse vortices (up/downwash), and flow mechanism near the body were not discussed sufficiently. In this study, the unsteady wake structures were analysed computationally using computational fluid dynamics to understand these issues, and the hypothesis was tested. The slant angle was 27.5°, which is identical to that in the experiment and corresponds to a high drag condition indicated experimentally.

One-way coupled simulation method that combines CFD, structural and acoustical analyses has been developed aiming at predicting the aeroacoustical interior noise for a wide range of frequency between 100 Hz and 4 kHz. Statistical Energy Analysis (SEA) has been widely used for evaluating transmission of sound through a car body and resulting interior sound field. Instead of SEA, we directly computed vibration and sound in order to investigate and understand propagation paths of vibration in a car body and sound fields. As the first step of this approach, we predicted the pressure fluctuations on the external surfaces of a car by computing the unsteady flow around the car. Secondly, the predicted pressure fluctuations were fed to the subsequent structural vibration analysis to predict vibration accelerations on the internal surfaces of the car.

A wall-resolving Large Eddy Simulation (LES) has been performed by using up to 40 billion grids with a minimum grid resolution of 0.1 mm for predicting the exterior hydrodynamic pressure fluctuations in the turbulent boundary layers of a test car with simplified geometry. At several sampling points on the car surface, which included a point on the side window, the door panel, and the front fender panel, the computed hydrodynamic pressure fluctuations were compared with those measured by microphones installed on the surface of the car in a wind tunnel, and effects of the grid resolution on the accuracy of the predicted frequency spectra were discussed. The power spectra of the pressure fluctuations computed with 5 billion grid LES agreed reasonably well with those measured in the wind tunnel up to around 2 kHz although they had some discrepancy with the measured ones in the low and middle frequencies.

The study of 10% ethanol blended gasoline (E10 gasoline) utilization has been conducted in the Japan Auto-Oil Program (JATOP). In order to clarify the impact of E10 gasoline on vehicle performances, exhaust emissions, evaporative emissions, driveability and material compatibility have been investigated by using domestic gasoline vehicles including mini motor vehicles which are particular to Japan. The test results reveal that E10 gasoline has no impact on exhaust emissions, engine startup time and acceleration period under the hot start condition, but a slight deterioration is observed in some test cases under the cold start condition using E10 gasolines with 50% distillation temperature (T50) level set to the upper limit of Japanese Industrial Standards (JIS) K 2202. Regarding evaporative emissions, the tested vehicles shows no remarkable increase in the hot soak loss (HSL), diurnal breathing loss (DBL) and running loss (RL) testing with E10 gasolines.

Increased interest in global warming requires rapid improvements in CO2 reduction efforts. The automotive industry is placing high importance on CO2 reduction technologies. Using Lithium-ion (Li-ion) battery pack Stop & Start (S&S) system with combined energy regeneration is an effective technology to reduce CO2 emissions. Power supply storage is very important for the S&S system. High charging acceptance, low weight, and compact size are required. A Li-ion battery is the optimal power supply that meets these requirements. It has high charge acceptance per weight. Furthermore, we developed simple system structure which eliminates the need for the DC-DC converter. By utilizing a Li-ion battery that has voltage characteristics similar to the Pb battery there is no need for a converter to make adjustments between the two power supplies. The Li-ion battery's range of capacity must be managed appropriately as overcharge and overdischarge causes extensive damage to the battery.

In open-grille vehicle aerodynamics simulation using computational fluid dynamics, in addition to basic flow characteristics, such as turbulent flow with a Reynolds number of several million on the bluff body, it is important to accurately estimate the cooling air flow introduced from the front opening. It is therefore necessary to reproduce the detailed geometry of the entire vehicle including the engine bay as precisely as possible. However, there is a problem of generating a good-quality calculation grid with a small workload. It usually takes several days to a week for the pretreatment process to make the geometry data ‘clean’ or ‘watertight’. The authors proposed a computational method for complex geometries with a hierarchical Cartesian grid and a topology-independent immersed boundary method with dummy cells that discretize the geometry on a cell-by-cell basis and can set an imaginary point arbitrarily.

A direct fuel-injection two-stroke cycle engine operated with neat methanol was investigated. The engine performance, combustion and exhaust-gas characteristics were analyzed experimentally and compared for operation with a carburetor, EFI injection at the intake manifold, and EFI injection at the scavenging port. The power and the brake thermal efficiency of the direct fuel-injection engine were higher than those of engines operated with a carburetor and either of the two EFI methods. The exhausted unburnt fuel of the direct fuel-injection engine was lower than that for operation with a carburetor, and formaldehyde and the CO concentration were of the same level as for operation with the carburetor and EFI methods. The NOx concentration of the direct fuel-injection was half the level of the result of carburetor operation.

The pulsations in the intake and exhaust systems affect both the intake and exhaust noises and the engine torque. The pulsations are mainly dominated by the standing waves, which are expressed by the acoustic characteristics. From this point of view, authors have developed an experimental method to analyze the standing wave and the acoustic transfer matrix, which is characterized as the four-pole parameters of the air column in an intake and exhaust system. In this paper, the intake and exhaust noises are predicted with the insertion loss based on the experiment. By using this method, first the experimental transfer matrix of each sub-system is obtained, then that of a whole system is superimposed from a combination of sub-systems. A proper combination of experimental transfer matrices and calculation ones enables to simulate the insertion loss with accuracy and efficiency.

Misfiring cycles were detected by a conditional sampling method to demonstrate the differences between firing and misfiring of the scavenging flow characteristics at the scavenging port and exhaust pipe using LDV method. The results show that the flow at the scavenging port was not influenced significantly by misfiring, but the blowdown flow in the exhaust pipe greatly depended on the combustion status. The blow-down flow of fired cycles at a light-load condition was very similar to the flow at a full-load condition. It was also found that measured flow characteristics at partial load should not be considered by averaging firing and misfiring cycles. The occurrence pattern of misfiring should be quantified and considered in the analysis.

The purpose of this study is to experimentally investigate in-cylinder flows with cyclic variation in a practical part-loaded two-stroke engine. First, the in-cylinder LDV measurements are introduced, which were carried out above the port layout and the combustion chamber as well as the exhaust pipe or the transfer port together with the simultaneous pressure measurements. Second, the in-cylinder flow characteristics in different combustion groups were discussed. The in-cylinder flow and the combustion-chamber flow were not simply characterized by the pressure variation in the engine or the other passage flow in the exhaust pipe or the transfer port. Finally, the in-cylinder flow structure with three stages was shown using the vector variation analysis and the drawing of the velocity profiles in the engine parts.

The purpose of this study was to detect a misfiring cycle in terms of the transfer-passage and the exhaust-pipe flow rate by experimental measurements. Simultaneous measurements of flow rates and in-cylinder pressure were carried out. The flow rate data were grouped into the different combustion classes by the in-cylinder pressure. A large flow rate of exhaust blow-down and a large reverse flow rate were observed in the cycle before misfiring, compared with in the cycle before firing. It showed that high concentration of the residual burnt gas in the cylinder was the main source of misfiring, this feature was also demonstrated by the complementary measurement of CO and CO2 concentrations.