Search Results

Partly competing objectives, as low fuel consumption, low friction, long oil maintenance rate, and at the same time lowest exhaust emissions have to be fulfilled. Diminishing resources, continuously reduced development periods, and shortened product cycles yield detailed knowledge about oil consumption mechanisms in combustion engines to be essential. There are different ways for the lubricating oil to enter the combustion chamber: for example as blow-by gas, leakage past valve stem seals, piston rings (reverse blow-by) and evaporation from the cylinder liner wall and the combustion chamber. For a further reduction of oil consumption the investigation of these mechanisms has become more and more important. In this paper the influence of the mixture formation and the resulting fuel content in the cylinder liner wall film on the lubricant oil emission was examined.

The steady increase of engine power and the demand of lightweight design along with enhanced reliability require an optimized dimensioning process, especially in cylinder head valve bridge, which is progressively prone to cracking. The problems leading to valve bridge cracking are high temperatures and temperature gradients on one hand and high mechanical restraining on the other hand. The accurate temperature estimation at the valve bridge center has significant outcomes for valve bridge thickness and width optimization. This paper presents a 1D heat transfer model, which is constructed through the cross section of the valve bridge center by the use of well known quasi-stationary heat convection and conduction equations and reduced from 3D to 1D via regression and empirical weighting coefficients. Several diesel engine cylinder heads with different application types and materials are used for model setup and verification.

A new turbocharged 60° 2.7L 4V-V6 gasoline engine has been developed by Ford Motor Company for both pickup trucks and car applications. This engine was code named “Nano” due to its compact size; it features a 4-valves DOHC valvetrain, a CGI cylinder block, an Aluminum ladder, an integrated exhaust manifold and twin turbochargers. The goal of this engine is to deliver 120HP/L, ULEV70 emission, fuel efficiency improvements and leadership level NVH. This paper describes the upfront design and optimization process used for the NVH development of this engine. It showcases the use of analytical tools used to define the critical design features and discusses the NVH performance relative to competitive benchmarks.

The higher cylinder peak pressure and pressure rise rate of modern diesel and gasoline fueled engines tend to increase combustion noise while customers demand lower noise. The multiple degrees of freedom in engine control and calibration mean there is more scope to influence combustion noise but this must first be measured before it can be balanced with other attributes. An efficient means to realize this is to calculate combustion noise from the in-cylinder pressure measurements that are routinely acquired as part of the engine development process. This publication reviews the techniques required to ensure accurate and precise combustion noise measurements. First, the dynamic range must be maximized by using an analogue to digital converter with sufficient number of bits and selecting an appropriate range in the test equipment.

Torque and performance requirements of Diesel engines are continually increasing while lower emissions and fuel consumption are demanded, thus increasing thermal and mechanical loads of the main components. The level of peak firing pressure is approaching 200 bar (even higher in Heavy Duty Diesel engines), consequently, a structural optimization of crankcase, crank train components and in particular of the cylinder head is required to cope with the increasing demands. This report discusses design features of cylinder head concepts which have the capability for increasing thermal and mechanical loads in modern Diesel engines

A three-step process was developed to estimate fracture criteria for a human body model. The process was illustrated via example wherein skull fracture criteria were estimated for the Ford Human Body Model (FHBM)~a finite element model of a mid-sized human male. The studied loading condition was anterior-to-posterior, blunt (circular/planar) cylinder impact to the frontal bone. In Step 1, a conditional reference risk curve was derived via statistical analysis of the tests involving fractures in a recently reported dataset (Cormier et al., 2011a). Therein, Cormier et al., authors reported results for anterior-to-posterior dynamic loading of the frontal bone of rigidly supported heads of male post mortem human subjects, and fracture forces were measured in 22 cases. In Step 2, the FHBM head was used to conduct some underlying model validations relative to the Cormier tests. The model-based Force-at-Peak Stress was found to approximate the test-based Fracture Force.

Internal combustion (IC) engines fueled by hydrogen are among the most efficient means of converting chemical energy to mechanical work. The exhaust has near-zero carbon-based emissions, and the engines can be operated in a manner in which pollutants are minimal. In addition, in automotive applications, hydrogen engines have the potential for efficiencies higher than fuel cells.[1] In addition, hydrogen engines are likely to have a small increase in engine costs compared to conventionally fueled engines. However, there are challenges to using hydrogen in IC engines. In particular, efficient combustion of hydrogen in engines produces nitrogen oxides (NOx) that generally cannot be treated with conventional three-way catalysts. This work presents the results of experiments which consider changes in direct injection hydrogen engine design to improve engine performance, consisting primarily of engine efficiency and NOx emissions.

Two-stroke gasoline engines are known to benefit from using in-cylinder fuel injection which improves their ability to meet the strict fuel economy and exhaust emissions requirements. A conventional method of in-cylinder fuel injection involves application of plunger-type positive displacement pumps. Two-stroke engines are usually smaller and lighter than their 4-stroke counterparts of equal power and need a pump that should also be small and light and, preferably, simple in construction. Because a 2-stroke engine fires every crankshaft revolution, its fuel injection pump must run at crankshaft speed (twice the speed of a 4-stroke engine pump). An electronically controlled fuel injection system has been designed to satisfy the needs of a small automotive 2-stroke engine capable of running at speeds of up to 6000 rpm.

The small-displacement direct-injection (DI) diesel engine is a prime candidate for future transportation needs because of its high thermal efficiency combined with near term production feasibility. Ford Motor Company and FEV Engine Technology, Inc. are working together with the US Department of Energy to develop a small displacement DI diesel engine that meets the key challenges of emissions, NVH, and power density. The targets for the engine are to meet ULEV emission standards while maintaining a best fuel consumption of 200g/kW-hr. The NVH performance goal is transparency with state-of-the-art, four-cylinder gasoline vehicles. Advanced features are required to meet the ambitious targets for this engine. Small-bore combustion systems enable the downsizing of the engine required for high fuel economy with the NVH advantages a four- cylinder has over a three-cylinder engine.

Two-stroke cycle direct injection engines can achieve adequate stability at idle with stratified combustion at very lean overall air-fuel ratio, but exhaust temperature is very low. A rotary valve system was designed to spill charge from the cylinder into the intake tract during the compression stroke, in order to allow stable operation at lower engine delivery ratio and thereby increase exhaust temperature. Reduction of the engine delivery ratio was not achieved due to the poor scavenging characteristics of the swirl liners used, which resulted in high content of exhaust residual gas in the spill recirculation flow. Although the concept objective of higher exhaust temperature was not realized, the results indicate that the concept may be feasible if high purity of the spill recirculation flow can be achieved in conjunction with high trapping efficiency.

Based on the TurboDISI engine presented earlier [1], [2], a new Spray Guided Turbo (SGT) concept with enhanced engine performance was developed. The turbocharged engine was modified towards utilizing a spray-guided combustion system with a central piezo injector location. Higher specific power and torque levels were achieved by applying specific design and cooling solutions. The engine was developed utilizing a state-of-the-art newly developed charge motion design (CMD) process in combination with single cylinder investigations. The engine control unit has a modular basis and is realized using rapid prototyping hardware. Additional fuel consumption potentials can be achieved with high load EGR, use of alternative fuels and a hybrid powertrain. The CO2 targets of the EU (120 g/km by 2012 in the NEDC) can be obtained with a mid-size vehicle applying the technologies presented within this paper.

The main tasks for all future powertrain developments are: regulated emissions, CO2-values, comfort, good drivability, high reliability and affordable costs. One widely discussed approach for fuel consumption improvement within passenger car applications, is to incorporate the downsizing effect. To attain constant engine performance an increase of boost pressure and/or rated speed is mandatory. In both cases, the mass flow rate through the intake and exhaust ports and valves will rise. In this context, the impact of the port layout on the system has to be reassessed. In this paper, the impact of the port layout on a modern diesel combustion system will be discussed and a promising concept shall be described in detail. The investigations shown include flow measurements, PIV measurements of intake flow, CFD simulations of the flow field during intake and results from the thermodynamic test bench. One of the important topics is to prove the impact of the flow quality on the combustion.

Multidimensional models that are used for engine computations must include spray sub-models when the fuel is injected into the cylinder in liquid form. One of these spray sub-models is the droplet interaction model, which is separated into two parts: first, calculation of a collision rate between drops, and second, calculation of the outcome once a collision has occurred. This paper focuses on the problem of calculating the collision rate between drops accurately. Computing the collision rate between drops or particles when they are non-uniformly distributed and sharp gradients are present in their distribution is a challenging task. Traditionally the collisions between parcels of drops have been computed using the same spatial grid as is used for the Eulerian gas-phase calculations. Recently it has been proposed to use a secondary grid for the collision rate calculation that is independent of the gas-phase grid, as is done in the NTC collision algorithm.

The Yuchai F-6113 is an inline 6-cylinder heavy duty Diesel engine, mainly for truck application with a displacement of 8.4 liters and a rated power of 258 kW. It was derived from the F-6108 with a displacement of 7.3 liters. The boundary conditions for the new crankcase were set by the existing machining line. Substantially increasing the bore diameter while keeping the bore pitch constant, was achieved by replacing the conventional top stop liner with a mid stop liner with open deck. This liner concept is rather unique for heavy duty truck engines. The two 2-valve cylinder heads, covering 3 cylinders each, were replaced by a 4-valve one-piece cylinder head. The design comprises an electronically controlled Unit Pump Injection System (UPS) with the alternative to use an inline injection pump. The engine structure was laid out for the high specific output and the peak cylinder pressure requirements for the compliance with Euro III emission legislation.

Beside the traditional prediction of stresses and verification by mechanical testing the optimization of cylinder liner bore distortion is one of today's most important topics in crankcase structure development. Low bore distortion opens up potentials for optimizing the piston group. As the piston rings achieve better sealing characteristics in a low deformation cylinder liner, oil consumption and blow-by are reduced. For unchanged oil consumption and blow-by demands, engine friction and subsequently, fuel consumption could be reduced by decreasing the pre-tension of the piston rings. From the acoustical point of view an optimization of piston-slap noise is often based on an optimized bore distortion behavior. Apart from basics to the behavior of liner bore distortion the paper presents advanced analytical and empirical methods for detailed prediction, verification and optimization of bore distortion taking into account the effective engine operation conditions.

Engine excitation forces have been studied in the past using one of two methods; a lumped sum or a totally distributed approach. The lumped sum approach gives the well-understood engine inherent unbalance and the totally distributed approach is used in engine CAE models to determine the overall engine response. The approach that will be described in this paper identifies an intermediate level of sophistication. The methodology implemented considers single cylinder forces on the engine block, piston side thrust and main bearing forces, and decomposes them into their order content. The forces are then phased and geometrically distributed appropriately for each cylinder and then each order is analyzed relative to know distributions that are NVH concerns, V-block breathing, block side wall breathing, and block lateral and vertical bending.

Due to today's demands to reduce cost and product time to market, engineering procedures are increasingly using more sophisticated simulation techniques, instead of validation testing. Early implementation of CAE methods yield higher quality products, even with first prototypes, reducing the design iterations required to reach production quality. The strategy is to conduct specific evaluations of a realistic representation of the product while focusing on the key boundary conditions necessary to extract fatigue effects. Discussed in this paper are adequate CAE methods for early identification, evaluation and removal of conceptual and local structural weaknesses. Possible solutions gained from a computational optimization process are discussed for highly loaded HSDI diesel cylinder heads as a representative example.

A Variable Displacement Engine (VDE) improves fuel economy by deactivating half the cylinders at light load. The actual fuel economy benefit attained in the vehicle depends on how often cylinders can be deactivated, which is a function of test cycle, engine size, and vehicle weight. In practice, cylinder deactivation will also be constrained by NVH (noise, vibration, and harshness). This paper presents fuel economy projections for VDE in several different engine and vehicle applications. Sensitivity to NVH considerations is quantified by calculating fuel economy with and without cylinder deactivation in various operating modes: idle, low engine speed, 1st and 2nd gear, and warm-up after cold start. The effects of lug limits and calibration hysteresis are also presented.

Several types of hybrid-electric vehicles have been developed at Ford Research Laboratory. Among the parallel hybrid systems with a single electric motor, two types were studied. In the first type, the electric motor was attached directly to the crankshaft (mild hybrid) [1], to enable the engine start-stop and regeneration functions. In the second type (full hybrid) the electric motor was connected to the engine through the use of a clutch to allow electric launch of the vehicle and pure electric driving at low speeds. The full hybrid powertrain described in this paper uses a more powerful electric motor for enhanced regenerative braking and engine power assist. An engine-disconnecting clutch saves energy during both the electric propulsion and during vehicle braking. When the clutch is disengaged the engine is shut-off, which eliminates the energy otherwise spent on motoring the engine during electric propulsion.