Search Results

Particulate matter is one of the major pollutant responsible for deteriorating air quality, particularly in urban centers. Information on contributing sources with the share from different sources is a first and one of the important steps in controlling pollution. Diverse sources, anthropogenic as well as natural, like industries, transport, domestic burning, construction, wind-blown dust, road dust contribute to particulate matter pollution. Receptor modeling is a scientific method which is utilized for assessment of the contribution of various sources based on chemical characteristics of particulate matter sources and ambient air particulate matter. Representative data of fractions of various chemical species in the particulate matter from the different sources i.e. source fingerprint is an essential input for the receptor modeling approach.

CNG has recently seen increased penetration within the automotive industry. Due to recent sanctions on diesel fuelled vehicles, manufactures have again shifted their attention to natural gas as a suitable alternative. Turbocharging of SI engines has seen widespread application due to its benefit in terms of engine downsizing and increasing engine performance [1]. This paper discusses the methodology involved in development of a multi cylinder turbocharged natural gas engine from an existing diesel engine. Various parameters such as valve timing, intake volume, runner length, etc. were studied using 1D simulation tool GT power and based on their results an optimized configuration was selected and a proto engine was built. Electronic throttle body was used to give better transient performance and emission control. Turbocharger selection and its location plays a critical role.

Major cause of air pollution in the world is due to burning of fossil fuels for transport application; around 23% GHG emissions are produced due to transport sector. Likewise, the major cause of air pollution in Indian cities is also due to transport sector. Marginal improvement in the fuel economy provide profound impact on surrounding air quality and lightweighting of vehicle mass is the key factor in improving fuel economy. The paper describes robust and integrated approach used for design and development of lightweight bus structures for Indian city bus applications. An attempt is made to demonstrate the use of environment friendly material like aluminium in development of lightweight superstrutured city buses for India. Exercise involved design, development and prototype manufacturing of 12m Low Entry and 12m Semi Low Floor (SLF) bus models.

The paper discusses the methodology for measuring the sound absorption of sound package materials in a different sizes of reverberation chambers. The large reverberation chamber is based on test methods and requirements as per ASTM C423 and ISO 354 standards. Both the test standards are similar and recommend a reverberation chamber volume of at least 125 m3 and 200 m3 respectively for sound absorption measurements from 100 Hz to 5000 Hz. The test sample size requirements are from 5.5 to 6.7 m2 as per ASTM C423 and 10 to 12 m2 as per ISO 354. In the automotive sector passenger car, heavy truck, and commercial vehicle, the parts that are used are much smaller in size than the size prescribed in both the standards. The requirement is to study the critical parameters such as the chamber volume, sample size, reverberation time and cut-off frequency etc. which are affecting the sound absorption property of acoustic material.

Sound Quality (SQ) of brake and clutch pedal assembly plays an important role in contributing to vehicle interior noise and perception of sound. Quiet operation of brake and clutch units also reflects the vehicle built and material quality. Noise emitted from these sub-assemblies has to meet certain acceptance criteria as per different OEM requirements. Not much work has been carried on this over the years to characterize and quantify the same. An attempt has been made in this paper to study the sound quality of brake and clutch pedal assemblies at component level and validate the same by identifying the parameters affecting SQ. Effect on noise at different environmental conditions was studied with typical operating cycles in a hemi-anechoic chamber. The effect of sensor switches integrated within the clutch and brake pedal on sound quality is analyzed. It is found that the operating characteristics of switches drives the noise and SQ.

Two carburetted passenger cars of different makes, converted for CNG (Compressed Natural Gas) operation (in dual mode) and optimised by ARAI (The Automotive Research Association of India, Pune, India), were tested for vehicular performance. The respective engines were also mapped for performance, energy consumption and emission. The power loss in CNG mode was 7% & 15% and torque reduction was 21% & 15% in respective engines. There is considerable improvement in thermal efficiency and reduction of emission in the entire operating range. The vehicle performance on Chassis Dynamometer shows similar results. The second engine was also tested with a ceramic catalytic converter which gave 93% reduction in CO and 50% reduction in HC in major portion of operating range. 1100 CC car was also tested on the test track. Optimisation work included installation of ARAI mixer design.

An open wheeled open cockpit high speed car with 800 CC MPFI engine was developed validated and run at 105 kmph. The key focus was to build a car with superior aerodynamic characteristics especially in terms of drag. This work discusses in detail about the design and simulation of car using CFD package followed by Wind Tunnel testing. The design of high speed car starts with design of seat according to the ergonomics of the driver followed by the space frame. Based on the space frame designed, the body panels are sketched and CAD model is developed. The CAD model is imported in CFD package for virtual testing and validated through wind tunnel results. For this 1:3 scale model was manufactured using Rapid Prototyping.

The design and development of complete vehicle, understanding of chassis system development process is an important task. Chassis frame of a vehicle is supporting member, both structurally and functionally, to all other chassis aggregate systems viz. suspension, steering, braking system etc. In this paper, a methodology for chassis frame model construction and validation is explained. In present work, chassis frame model is validated in terms of modal parameters and also against static loading conditions. Existing chassis 3D Computer Aided Design (CAD) data was generated using scanning and cloud point data conversion technique. FE model was generated and validated through experimental measurements viz. modal testing, vertical bending, lateral bending, and torsional bending test. Loading and boundary conditions were replicated on the complete FE model in CAE domain and test validation was carried out using appropriate mesh biasing and weld modeling techniques.

New process development of forging component requires in-depth knowledge and experience related to the process. Also it requires number of physical trials to arrive at optimum process and initial billet dimensions. With the help of reliable computer simulation tool, it is possible to optimize the complete forging process and billet dimensions. Simulation provides much more insight about the process and possible forging defects. This saves considerable time and money. This paper describes about a complete forging process designed for a complex component. With the help of metal forming simulation software, complete forging process was simulated and optimized. Forging defects were removed during optimization of the process. Billet weight optimization was also carried out. Deciding the preforming shape of the billet was the main challenge. An innovative pre-forging shape was arrived which resulted in eliminating one process stage.

Forging is a metal forming process involving shaping of metal by the application of compressive forces using hammer or press. Forging load of equipment is an important function of forging process and the prediction of the same is essential for selection of appropriate equipment. In this study a hot forging material i.e. 42CrMo4 steel is selected which is used in automotive components like axle, crank shaft. Hot forging experiments at 750°C are carried out on cylindrical specimens of aspect ratio 0.75 and 1.5 with true height strain (ln (ho/hf)) of 0.6. Forging load for the experiments is calculated using slab and upper bound deformation models as well as Metal forming simulation using commercially available FEA software. The upper bound models with 30% deviation from the simulation results are found to be more accurate compared to the slab models.

In today’s scenario, the emission norms are getting stringent day by day due to an increased level of pollution. The world is shifting towards low carbon footprint which made it necessary to adopt efficient technologies with fewer emissions. The hybridization of vehicles has resulted in improved efficiency with lower emissions which can fulfil the near future emission norms. Retrofitting of hybrid components into a conventional IC engine vehicle is so far the best way to achieve better performance both economically and technologically. This research is primarily focused on the design and development of a novel retrofit solution of P3x architecture for the light commercial vehicle. This retrofit solution is different from other hybrid solutions in terms of powertrain. It contains an innovative add-on powertrain along with the existing powertrain. This additional powertrain consists of a pair of helical gears followed by a chain and sprocket as a coupler for traction motor.

Any change is vehicle exterior design, affects the aerodynamics characteristic. Generally different types of roof racks are attached on passenger vehicles to carry luggage which affects aerodynamic drag. The objective of this work is to perform aerodynamic analysis of ground vehicle with roof rack to investigate the change in drag coefficient. First, the aerodynamic analysis of a baseline passenger car model is performed with and without generic benchmarked roof rack at 100 kmph. Further analysis is carried out with different new designs of roof racks. Based on simulation result, a scaled down prototype model is fabricated and validated by using a wind tunnel test for optimum suitable case. The modelling of the vehicle is done in CATIA tool and simulation is carried out by using ANSYS Fluent.

Alternative fuels for both spark ignition (SI) and compression ignition (CI) engines have become very important owing to increased environmental protection concern, the need to reduce dependency on petroleum and even socioeconomic aspects. An appropriate sustainable fuel alternative has turn out to be a main concern and bio-diesel is one of the sustainable fuels. The path of interest in biodiesel has highlighted its advantages which include decrease in hydrocarbon and particulate matter. Meanwhile its shortcoming includes higher emission of oxides of nitrogen. This work is an attempt to develop a mathematical relationship to predict thermal NOx in CI engine fuelled with neat biodiesel. Attention was focused on using in-cylinder pressure based variables to predict NOx. In cylinder pressure measurement is a valuable tool for the analysis of CI engine combustion, which is used for finding the heat release rate, ignition delay, etc.

Occupant motion in a vehicle rollover accident is a function of many factors. Some important ones are vehicle kinematics, position of the occupant in the vehicle, occupant size, ground topology and restraint usage. The far side belted occupants are more vulnerable than the near side occupants in a rollover accident as they have more energy as a result of their trailing and higher side of the vehicle. This outcome is attributable to the inadequate safety performance of the conventional single loop; B-pillar mounted D-ring restraints. Roof crush tends to displace the vehicle's B-pillar, resulting in D-Ring displacement which causes slack in the lap portion of the restraint. This slack enables centrifugal loads to move the far side occupant further away from the vehicle's instantaneous point of rotation. In this scenario, the presence of any ejection portal can result in an occupant becoming partially or fully ejected.

Material handling is a major section in all the industries especially for delicate and huge components. Here in this industry they are using pneumatics system to tilt the component for certain angle so that operator will be able to do the further operation in the line. Pneumatic system needs compressed air for running the system, which in turn requires electricity to compress the air using an air compressor. Due to frequent power shutdowns many industries are facing problem to run their manufacturing unit peacefully. As an alternate they are using generators which require fuel to generate power. This adds excess cost for manufacturing the products and demand for fuel is also increasing day by day. So to avoid all this problem with a one step solution, dependability of energy resources has to be minimized. For avoiding the usage of energy resources the usage of pneumatics and compressed air has to be reduced.

Nickel electroplating is commonly used with substrates including steel, aluminum, plastic and zinc die-cast parts because of its high resistance to temperature, corrosion and wear in harsh conditions. To further enhance its tribological and mechanical properties, research works are going on to produce nano-reinforced composites of Ni with various ceramic and rare earth oxides like CeO2, ZrSiO4, SiC, TiO2, etc. The aim of present work is synthesis and characterization of Ni films and Ni based TiO2 nano-composite coating processed by pulse co-electrodeposition technique. Also, to investigate the various properties such as mechanical, wear and corrosion resistance, conductivity & thermal stability of Ni-TiO2 nanocomposites electrodeposited on steel substrate, especially the effects of the amount of nanosized TiO2 particles in Ni-TiO2 nanocomposites.

Biodiesel is an alternate fuel for diesel consisting of the alkyl monoester of fatty acids derived from vegetable oils. The most usual method to transform oil into biodiesel is transesterification which can be carried out using different catalyst. Jatropha is second generation oil which is non edible and can be use for producing biodiesel. The first part is to expel oil from jatropha seeds. There are different types of expelling methods such as mechanical extraction, solvent extraction and enzymatic extraction. The study was conducted with hand driven mechanical expeller which is most conventional way of extracting oil from seeds with mechanical efficiency of 60-80% for single pass. The study includes various combinations of parameters like seed treatment, sun drying, pre-heating, soaking at different temperatures and different de-hulling compositions.

Frontal crash is the most common type of accidents in passenger vehicles which results in severe injuries or fatalities. During frontal crash, some frontal vehicle body has plastic deformation and absorbs impact energy. Hence vehicle crashworthiness is important consideration for safety aspect. The crash box is one of the most important parts in vehicle frontal structure assembly which absorb crash energy during impact. In case of frontal crash accident, crash box is expected to be collapsed by absorbing crash energy prior to the other parts so that the damage to the main cabin frame and occupant injury can be minimized. The main objective of this work is to design and optimize the crash box of passenger vehicle to enhance energy absorption. The modeling of the crash box is done in CATIA V5 and simulations are carried out by using ANSYS. The results show significant improvement in the energy absorption with new design of the crash box and it is validated experimentally on UTM.

Ride Comfort forms a core design aspect for suspension and is to be considered as primary requirement for vehicle performance in terms of drivability and uptime of passenger. Maintaining a balance between ride comfort and handling poses a major challenge to finalize the suspension specifications. The objective of this project it to perform ride- comfort analysis for a commercial truck using MATLAB Simulink. First, benchmarking was carried out on a 4x2 commercial truck and the physical parameters were obtained. Further, a mathematical model is developed using MATLAB Simulink R2015a and acceleration- time data is collected. An experimentation was carried out on the truck at speeds of 20 kmph, 30 kmph, 40 kmph and 50 kmph over a single hump to obtain actual acceleration time domain data. The model is then correlated with actual test over a single hump. This is followed by running the vehicle on Class A, B & C road profiles to account for random vibrations.

Microalgae as feedstock are the potential third generation biofuels. Microalgae are photosynthetic microorganism which requires light, carbon-di-oxide, nitrogen, phosphorous, and potassium for growth and to produce lipids, proteins and carbohydrates in large amounts over short a periods of time. The production of biofuels from microalgal is a viable alternative due to their easy adaptability to growth conditions, possibility of growing biomass either in fresh or marine waters. Hence the current project was designed to elucidate the biodiesel producing ability of blue-green algae such as Spirulina platensis and Green algae Chlorella vulgaris. The selected algae were cultivated in suitable growth media such as modified Zarrouke medium and bold basal medium, respectively. The Spirulina platensis and Chlorella vulgaris were mass cultured for 8 days then harvested using 50 micron nylon filters and dried in sunlight to obtain dry biomass.