Search Results

Modern hybrid technologies, especially mild and micro-hybrids with auto start/stop feature, demand a starter with higher power, better performance and longer life than conventional brush-type starters. In this paper, a new starter design using a brushless motor is proposed. This improves the engine crank performance during autostarts due to lower inertia, higher torque and wider power band capability of the brushless motor, especially at higher speeds. The overall integrated system includes the motor, inverter and controller all packaged in the same form factor of the original starter housing as a “drop-in replacement”. The prototype starter motor is designed to operate at 48V with a peak power of 4kW but can be designed to operate at the standard 12V. This paper will describe in detail the functionalities of the overall system and the simulation and experimental results of the prototype that was tested on a 4-cylinder engine in a production crossover vehicle.

Improving vehicle response through advanced knowledge of traffic behavior can lead to large improvements in energy consumption for the single isolated vehicle. This energy savings across multiple vehicles can even be larger if they travel together as a cohort in harmonization. Additionally, if the vehicles have enough information about their immediate path of travel, and other vehicles’ in that path (and their respective critical forward-looking information), they can safely drive close enough to each other to share aerodynamic load. These energy savings can be upwards of multiple percentage points, and are dependent on several criteria. This analysis looks at criteria that contributes to energy savings for a cohort of vehicles in synchronous motion, as well as describes a study that allows for better understanding of the potential benefits of different types of cohorted vehicles in different platoon arrangements.

Disc brakes operate with very close proximity of the brake pads and the brake rotor, with as little as a tenth of a millimeter of movement of the pads required to bring them into full contact with the rotor to generate braking torque. It is usual for a disc brake to operate with some amount of residual drag in the fully released state, signifying constant contact between the pads and the rotor. With this contact, every miniscule movement of the rotor pushes against the brake pads and changes the forces between them. Sustained loads on the brake corner, and maneuvers such as cornering, can both produce rotor movement relative to the caliper, which can push it steadily against one or both of the brake pads. This can greatly increase the residual force in the caliper, and increase drag. This dependence of drag behavior on the movement of the brake rotor creates some vehicle-dependent behavior.

This paper presents an overview of the connected controls and optimization system for vehicle dynamics and powertrain operation on a light-duty plug-in multi-mode hybrid electric vehicle developed as part of the DOE ARPA-E NEXTCAR program by Michigan Technological University in partnership with General Motors Co. The objective is to enable a 20% reduction in overall energy consumption and a 6% increase in electric vehicle range of a plug-in hybrid electric vehicle through the utilization of connected and automated vehicle technologies. Technologies developed to achieve this goal were developed in two categories, the vehicle control level and the powertrain control level. Tools at the vehicle control level include Eco Routing, Speed Harmonization, Eco Approach and Departure and in-situ vehicle parameter characterization.

Road induced structural feel “vehicle feels solidly built” is strongly related to the vehicle ride [1]. Excellent structural feel requires both structural and suspension dynamics considerations simultaneously. Road induced structural feel is defined as customer facing structural and component responses due to tire force inputs stemming from the unevenness of the road surface. The customer interface acceleration and noise responses can be parsed into performance criteria to provide design and tuning vehicle integration program recommendations. A dynamic impact bump method is developed for vehicle level structural feel performance assessment, diagnostics, and development tuning. Current state of on-road testing has the complexity of multiple impacts, averaging multiple road induced tire patch impacts over a length of a road segment, and test repeatability challenges.

The General Motors Aero Lab’s Full-Scale Wind Tunnel Facility, which came into operation in August of 1980[1], has undergone the significant upgrade of installing a state-of-the-art moving ground plane system. After almost four decades of continuous use the full-scale wind tunnel also received some significant maintenance to other areas, including a new heat exchanger, main fan overhaul, and replacement of the test section acoustic treatment. A 5-belt system was installed along with an integrated vehicle lift system. The center belt measures 8.5m long and can accommodate two belt widths of 1100mm and 950mm. Flow quality and other wind tunnel performance parameters were maintained to prior specifications which are on par with the latest industry standards [2]. The new 5-belt rolling road system maintains GM’s industry leading vehicle aerodynamic development and the improved acoustic panels ensure GM continues to develop vehicles with leading class acoustics.

There has been an increasing interest in exploring the potential to reduce energy consumption of future connected and automated vehicles. People have extensively studied various eco-driving implementations that leverage preview information provided by on-board sensors and connectivity, as well as the control authority enabled by automation. Quantitative real-world evaluation of eco-driving benefits is a challenging task. The standard regulatory driving cycles used for measuring exhaust emissions and fuel economy are not truly representative of real-world driving, nor for capturing how connectivity and automation might influence driving trajectories. To adequately consider real-world driving behavior and potential “off-cycle” impacts, this paper presents four collaborative evaluation methods: large-scale simulation, in-depth simulation, vehicle-in-the-loop testing, and vehicle road testing.

Damping measurements on vehicle subsystems are rarely straightforward due to the complexity of the dynamic interaction of system joints, trim, and geometry. Various experimental techniques can be used for damping estimation, such as frequency domain modal analysis curve-fitting methods, time domain decay-rate methods, and other methods based on energy and wave propagation. Each method has its own set of advantages and drawbacks. This paper describes an analytical and an experimental comparison between two, widely used loss factor estimation techniques frequently used in Statistical Energy Analysis (SEA). The single subsystem Power Injection Method (PIM) and the Impulse Response Decay Method (IRDM) were compared using analytical models of a variety of simulated simple spring-mass-damper systems. Frequency averaged loss factor values were estimated from both methods for comparison.

Power split in Fuel Cell Hybrid Electric Vehicles (FCHEVs) has been controlled using different strategies ranging from rule-based to optimal control. Dynamic Programming (DP) and Model Predictive Control (MPC) are two common optimal control strategies used in optimization of the power split in FCHEVs with a trade-off between global optimality of the solution and online implementation of the controller. In this paper, both control strategies are developed and tested on a FC/battery vehicle model, and the results are compared in terms of total energy consumption. In addition, the effects of the MPC prediction horizon length on the controller performance are studied. Results show that by using the DP strategy, up to 12% less total energy consumption is achieved compared to MPC for a charge sustaining mode in the Urban Dynamometer Driving Schedule (UDDS) drive cycle.

This paper presents real-world driving energy and fuel consumption results for the second-generation Chevrolet Volt plug-in hybrid electric vehicle (PHEV). A drive cycle, local to Michigan Technological University, was designed to mimic urban and highway driving test cycles in terms of distance, transients and average velocity, but with significant elevation changes to establish an energy intensive real-world driving cycle for assessing potential energy savings for connected and automated vehicle (CAV) control. The investigation began by establishing baseline and repeatability of energy consumption at various battery states of charge. It was determined that drive cycle energy consumption under a randomized set of boundary conditions varied within 3.6% of mean energy consumption regardless of initial battery state of charge.

Adaptive cruise control is an advanced vehicle technology that is unique in its ability to govern vehicle behavior for extended periods of distance and time. As opposed to standard cruise control, adaptive cruise control can remain active through moderate to heavy traffic congestion, and can more effectively reduce greenhouse gas emissions. Its ability to reduce greenhouse gas emissions is derived primarily from two physical phenomena: platooning and controlled acceleration. Platooning refers to reductions in aerodynamic drag resulting from opportunistic following distances from the vehicle ahead, and controlled acceleration refers to the ability of adaptive cruise control to accelerate the vehicle in an energy efficient manner. This research calculates the measured greenhouse gas emissions benefit of adaptive cruise control on a fleet of 51 vehicles over 62 days and 199,300 miles.

This paper presents the development of a reduced-order powertrain model for energy and SOC estimation of a multi-mode plug-in hybrid electric vehicle using only vehicle speed profile and route elevation as inputs. Such a model is intended to overcome the computational inefficiencies of higher fidelity powertrain and vehicle models in short and long horizon energy optimization efforts such as Coordinated Adaptive Cruise Control (CACC), Eco Approach and Departure (EcoAND), Eco Routing, and PHEV mode blending. The reduced-order powertrain model enables Connected and Automated Vehicles (CAVs) to utilize the onboard sensor and connected data to quickly react and plan their maneuvers to highly dynamic road conditions with minimal computational resources.

This paper presents a methodology to optimize the blending of charge-depleting (CD) and charge-sustaining (CS) modes in a multi-mode plug-in hybrid electric vehicle (PHEV) that reduces overall energy consumption when the selected route cannot be completely driven in all-electric mode. The PHEV used in this investigation is the second-generation Chevrolet Volt and as many as four instrumented vehicles were utilized simultaneously on road to acquire validation data. The optimization method used is dynamic programming (DP) paired with a reduced-order powertrain model to enable onboard embedded controller compatibility and computational efficiency in optimally blending CD, CS modes over the entire drive route.

This paper presents a methodology that optimizes the periods of engine operation on a selected route for a Plug-in Hybrid Electric Vehicle (PHEV) or Hybrid Electric Vehicle (HEV) using Connected Vehicle data to minimize energy consumption. The study was conducted using a Reduced-Order Powertrain model of second-generation Chevrolet Volt. The method utilizes the Backward Induction Dynamic Programming algorithm to come up with an optimal control mode matrix of engine operation along the selected route for various battery states of charge. The objective of this method is to make use of Vehicle Connectivity to minimize the energy utilization of an HEV by using the speed and elevation profile of a selected route transmitted to the vehicle via V2X communication systems.

Driver behavior models play a significant role in representing different driving styles and the associated relationships with traffic patterns and vehicle energy consumption in simulation studies. The models often serve as a proxy for baseline human driving when assessing energy-saving strategies that alter vehicle velocity. Such models are especially important in connectivity-enabled energy-saving strategy research because they can easily adapt to changing driving conditions like posted speed limits or change in traffic light state. While numerous driver models exist, parametric driver models provide the flexibility required to represent variability in real-world driving through different combinations of model parameters. These model parameters must be informed by a representative set of parameter values for the driver model to adequately represent a real-world driver.

Dry dual clutch transmission (DCT) has played an important role in the high performance applications as well as low-cost market sectors in Asia, with a potential as the future mainstream transmission technology due to its high mechanical efficiency and driving comfort. Control system simplification and cost reduction has been critical in making dry DCT more competitive against other transmission technologies. Specifically, DCT clutch actuation system is a key component with a great potential for cost-saving as well as performance improvement. In this paper, a new motor driven clutch actuator with a force-aid lever has been proposed. A spring is added to assist clutch apply that can effectively reduce the motor size and energy consumption. The goal of this paper is to investigate the feasibility of this new clutch actuator, and the force-aid lever actuator's principle, physical structure design, and validation results are discussed in details.

There have been tremendous improvements in China fuel quality in recent years in conjunction with newly implemented vehicle emissions standards to combat air pollution. The focus of concern is particulate emissions from gasoline engines especially from high volume gasoline direct inject (GDI) engines, therefore the China 6 (GB 18351.6-2016) emission standard introduces strict PM/PN requirements. Because the fuel and vehicle are an integrated system, the composition of gasoline is one of the factors affecting PM/PN emissions. Ethanol and aromatics are widely used as octane boosters, changing the composition of China’s gasoline pool. In this study, two gasoline oxygenates, ethanol and methyl tert-butyl ether (MTBE), and heavy aromatic hydrocarbons were studied in vehicles with a GDI engines. Vehicle tests were performed on the Worldwide Harmonized Light Vehicles Test Cycle (WLTC).

General Motors Global Propulsion Systems’ first nine-speed automatic transmission makes its debut in the 2017 Chevrolet Malibu, advancing a legacy of multispeed transmissions designed to optimize efficiency, performance and refinement. The Hydra-Matic 9T50 nine-speed is paired with a Ecotech 2.0L Turbo engine in the Malibu, contributing to an EPA estimated 33 mpg highway, a three-percent increase over the 2016 Malibu with an eight-speed automatic paired to the same engine. The 9T50 has a wider 7.6:1 overall ratio, which is the ratio between the first gear ratio and the top gear ratio, - compared to the six-speed’s 6.0:1 ratio. The 9T50 is fitted with a “deep” 4.69 first gear ratio for excellent off-the-line acceleration and a “tall” 0.62 top gear ratio for low-rpm highway cruising. That balance optimizes acceleration and fuel economy while reducing engine noise during cruising.

The purpose of this investigation is to present a control strategy and energy recovery potential for P2 parallel hybrid step gear automatic transmissions. The automatic transmission types considered for the investigation are rear wheel drive 8 speed dual clutch transmission and 8 speed planetary automatic equipped each equipped with an electric motor between the engine and transmission. The governing equations of clutch-to-clutch upshift controls are presented and are identical for each transmission type. Various strategies are explored for executing the upshift under a range of input torques, shift times and engine torque management approaches. The differences in energy recovery potential based upon control strategy is explored piecewise as well as through a DFSS study. On a comprehensive drive cycle consisting of FTP 75, US06 and HWFET test cycles, it is shown that upshift regen torque management can be equivalent to approximately 0.8% of the total fuel energy used.

Off road navigation demands ground robots to traverse complex and often changing terrain. Classification and assessment of terrain can improve path planning strategies by reducing travel time and energy consumption. In this paper we introduce a terrain classification and assessment framework that relies on both exteroceptive and proprioceptive sensor modalities. The robot captures an image of the terrain it is about to traverse and records corresponding vibration data during traversal. These images are manually labelled and used to train a support vector machine (SVM) in an offline training phase. Images have been captured under different lighting conditions and across multiple locations to achieve diversity and robustness to the model. Acceleration data is used to calculate statistical features that capture the roughness of the terrain whereas angular velocities are used to calculate roll and pitch angles experienced by the robot.