Search Results

Diesel injection parameters effect on liquid-phase diesel spray penetration after the end-of-injection (EOI) is investigated in a constant-volume chamber over a range of ambient and injector conditions typical of a diesel engine. Our past work showed that the maximum liquid penetration length of a diesel spray may recede towards the injector after EOI at some conditions. Analysis employing a transient jet entrainment model showed that increased fuel-ambient mixing occurs during the fuel-injection-rate ramp-down as increased ambient-entrainment rates progress downstream (i.e. the entrainment wave), permitting complete fuel vaporization at distances closer to the injector than the quasi-steady liquid length. To clarify the liquid-length recession process, in this study we report Mie-scatter imaging results near EOI over a range of injection pressure, nozzle size, fuel type, and rate-of-injection shape. We then use a transient jet entrainment model for detailed analysis.

The impact of fuel injection pressure on the development of diesel flames has been studied in a light-duty optical engine. Planer laser-induced fluorescence imaging of fuel (fuel-PLIF) and hydroxyl radicals (OH-PLIF) as well as line-of-sight integrated chemiluminescence imaging of cool-flame and OH* were performed for three different common-rail pressures including 70, 100, and 130 MPa. The injection timing and injected fuel mass were held constant resulting in earlier end of injection for higher injection pressure. The in-cylinder pressure was also measured to understand bulk-gas combustion conditions through the analysis of apparent heat release rate. From the cool-flame images, it is found that the low-temperature reaction starts to occur in the wall-interacting jet head region where the fuel-air mixing could be enhanced due to a turbulent ring-vortex formed during jet-wall interactions.

The importance of radiative heat transfer on the combustion and soot formation characteristics under nominal ECN Spray A conditions has been studied numerically. The liquid n-dodecane fuel is injected with 1500 bar fuel pressure into the constant volume chamber at different ambient conditions. Radiation from both gas-phase as well as soot particles has been included and assumed as gray. Three different solvers for the radiative transfer equation have been employed: the discrete ordinate method, the spherical-harmonics method and the optically thin assumption. The radiation models have been coupled with the transported probability density function method for turbulent reactive flows and soot, where unresolved turbulent fluctuations in temperature and composition are included and therefore capturing turbulence-chemistry-soot-radiation interactions. Results show that the gas-phase (mostly CO2 ad H2O species) has a higher contribution to the net radiation heat transfer compared to soot.

Shadowgraph/schlieren imaging techniques have often been used for flow visualization of reacting and non-reacting systems. In this paper we show that high-speed shadowgraph visualization in a high-pressure chamber can also be used to identify cool-flame and high-temperature combustion regions of diesel sprays, thereby providing insight into the time sequence of diesel ignition and combustion. When coupled to simultaneous high-speed Mie-scatter imaging, chemiluminescence imaging, pressure measurement, and spatially-integrated jet luminosity measurements by photodiode, the shadowgraph visualization provides further information about spray penetration after vaporization, spatial location of ignition and high-temperature combustion, and inactive combustion regions where problematic unburned hydrocarbons exist. Examples of the joint application of high-speed diagnostics include transient non-reacting and reacting injections, as well as multiple injections.

Diesel low-temperature combustion strategies often rely on early injection timing to allow sufficient fuel-ambient mixing to avoid NOx and soot-forming combustion. However, these early injection timings permit the spray to penetrate into a low ambient temperature and density environment where vaporization is poor and liquid impingement upon the cylinder liner and piston bowl are more likely to occur. The objective of this study is to measure the transient liquid and vapor penetration at early-injection conditions. High-speed Mie-scatter and shadowgraph imaging are employed in an optically accessible chamber with a free path of 100 mm prior to wall impingement and using a single-spray injector. The ambient temperature and density within the chamber are well-controlled (uniform) and selected to simulate in-cylinder conditions when injection occurs at -40 crank-angle degrees (CAD) or fewer before top-dead center (TDC).

Methods for detection of the spatial position and timing of diesel ignition with improved accuracy are demonstrated in an optically accessible constant-volume chamber at engine-like pressure and temperature conditions. High-speed pressure measurement using multiple transducers, followed by triangulation correction for the speed of the pressure wave, permits identification of the autoignition spatial location and timing. Simultaneously, high-speed Schlieren and broadband chemiluminescence imaging provides validation of the pressure-based triangulation technique. The combined optical imaging and corrected pressure measurement techniques offer improved understanding of diesel ignition phenomenon. Schlieren imaging shows the onset of low-temperature (first-stage) heat release prior to high-temperature (second-stage) ignition. High-temperature ignition is marked by more rapid pressure rise and broadband chemiluminescence.

Stringent particulate emission regulations are applied to spark-ignition direct-injection (SIDI) engines, calling for a significant in-cylinder reduction of soot particles. To enhance fundamental knowledge of the soot formation and oxidation process inside the cylinder of the engine, a new in-flame particle sampling system has been developed and implemented in a working optical SIDI engine with a side-mounted, wall-guided injection system. Using the sampling probes installed on the piston top, the soot particles are directly sampled from the petrol flame for detailed analysis of particle size distribution, structure, and shape. At the probe tip, a transmission electron microscope (TEM) grid is stored for the soot collection via thermophoresis, which is imaged and post-processed for statistical analysis. Simultaneously, the flame development was recorded using two high-speed cameras to evidence the direct exposure of the sampling grids to the soot-laden diffusion flames and pool fires.

For a better understanding of soot formation and oxidation processes in conventional diesel and biodiesel spray flames, the morphology, microstructure and sizes of soot particles directly sampled in spray flames fuelled with US#2 diesel and soy-methyl ester were investigated using transmission electron microscopy (TEM). The soot samples were taken at 50mm from the injector nozzle, which corresponds to the peak soot location in the spray flames. The spray flames were generated in a constant-volume combustion chamber under a diesel-like high pressure and high temperature condition (6.7MPa, 1000K). Direct sampling permits a more direct assessment of soot as it is formed and oxidized in the flame, as opposed to exhaust PM measurements. Density of sampled soot particles, diameter of primary particles, size (gyration radius) and compactness (fractal dimension) of soot aggregates were analyzed and compared. No analysis of the soot micro-structure was made.

In-flame soot sampling based on the thermophoresis of particles and subsequent transmission electron microscope (TEM) imaging has been conducted in a diesel engine to study size, shape and structure of soot particles within the reacting diesel jet. A direct TEM sampling is pursued, as opposed to exhaust sampling, to gain fundamental insight about the structure of soot during key formation and oxidation stages. The size and shape of soot particles aggregate structure with stretched chains of spherical-like primary particles is currently an unknown for engine soot modelling approaches. However, the in-flame sampling of soot particles in the engine poses significant challenges in order to extract meaningful data. In this paper, the engine modification to address the challenges of high-pressure sealing and avoiding interference with moving valves and piston are discussed in detail.

Influence of the injection pressure on the temporal evolution of lifted jet flame base upon the bowl wall impingement has been studied in a small-bore optical diesel engine. Previous studies suggest that the jet-wall interaction causes re-entrainment of combustion products into the incoming jet, which shortens the lift-off length during the injection and thereby increasing downstream soot. After the end of injection, the flame base slowly moves downstream as the diminishing jet momentum results in reduced re-entrainment. How the injection pressure impacts this transient behaviour of the flame base is a main focus of the present study. Common-rail pressure was varied from 70 to 160 MPa at a fixed injection mass (10 mg per hole) and timing (7°CA bTDC).

This study aims to develop innovative plasma combustion system to improve fuel economy and achieve higher efficiency without any modification of current engine configuration. A new plasma generation technique, that used a combination of spark discharge and microwave, was proposed. This technique was applied to gasoline engine as an ignition source, which was intensive and stable even in lean condition. In this technique, firstly, small plasma source was generated by spark discharge. Secondly, microwave was radiated to the plasma source to expand the plasma. The microwave power was absorbed by the plasma source and large non-thermal plasma was formed. In non-thermal plasma, the electron temperature was high and the gas temperature was low. Then many OH radicals were generated in the plasma. The frequency of the microwave was 2.45 GHz because we used a magnetron for microwave oven. Magnetrons for microwave oven were high efficiency and reasonable.

One major drawback of spark-ignition direct-injection (SIDI) engines is increased particulate matter (PM) and unburned hydrocarbon emissions at high load, due to wall wetting and a reduction in available air/fuel mixing time when compared to port-fuel injection (PFI). It is therefore necessary to understand the mechanics behind injection strategies which are capable of reducing these emissions while also maintaining the performance and efficiency of the engine. This study investigates the effect of varying the number fuel injection events and equivalence ratio on the operation of a wall-guided SIDI (WG-SIDI) engine. Of particular interest is how increased mixture homogeneity achieved by the double injection events impacts in-cylinder conditions and flame development.

One major drawback of spark-ignition direct-injection (SIDI) engines is increased particulate matter (PM) emissions at high load, due to increased wall wetting and a reduction in available mixture preparation time when compared to port-fuel injection (PFI). It is therefore necessary to understand the mechanics behind injection strategies which are capable of reducing these emissions while also maintaining the performance and efficiency of the engine. Splitting the fuel delivery into two or more injections is a proven way of working towards this goal, however, many different injection permutations are possible and as such there is no clear consensus on what constitutes an ideal strategy for any given objective. In this study, the effect of the timing of the first and second injections for an evenly split dual injection strategy are investigated in an optical SIDI engine running at 1200 RPM with an unthrottled intake.

A plasma combustion system was developed to improve fuel economy and efficiency without modifying the engine configuration. Non-thermal plasma generation technology with microwave was applied. Plasma was generated by spark discharge and expanded using microwaves that accelerated the plasma electrons, generating non-thermal plasma. Even at high pressures, spark discharge occurred, allowing plasma generation under high pressures. The durability and practicality of previous plasma combustion systems was improved. The system consisted of a spark plug without a resistor, a mixer circuit, and a control system. The mixer unit used a standard spark plug for plasma combustion and functioned as a high-voltage and high-frequency isolator. A commercially available magnetron produced microwaves of 2.45 GHz. The spark and microwave control system used a trigger signal set to the given crank angle, from the engine control unit.

Engine-out CO emission and fuel conversion efficiency were measured in a highly-dilute, low-temperature diesel combustion regime over a swirl ratio range of 1.44-7.12 and a wide range of injection timing. At fixed injection timing, an optimal swirl ratio for minimum CO emission and fuel consumption was found. At fixed swirl ratio, CO emission and fuel consumption generally decreased as injection timing was advanced. Moreover, a sudden decrease in CO emission was observed at early injection timings. Multi-dimensional numerical simulations, pressure-based measurements of ignition delay and apparent heat release, estimates of peak flame temperature, imaging of natural combustion luminosity and spray/wall interactions, and Laser Doppler Velocimeter (LDV) measurements of in-cylinder turbulence levels are employed to clarify the sources of the observed behavior.

The purpose of this study is to experimentally understand the cyclic variation of combustion state in a two-stroke engine with respect to the variations in scavenging flow and the CO and CO2 emissions. The criteria of grouping combustion states into misfiring were established using the in-cylinder pressure at the crankangle of maximum variability in peak pressure instead of indicated mean effective pressure. The CO and CO2 emissions and the flow velocity variations in the transfer port and the exhaust pipe were measured. Combustion of each cycle was grouped into misfiring, incomplete firing or firing by the criteria of the in-cylinder pressure. In the cycle before misfiring, the CO and CO2 concentration showed high level and the first peak of the exhaust flow showed large velocity and the positive velocity remained for long duration, and the exhaust and the transfer port flow were steeply decelerated to negative velocity midway between scavenge port opening and bottom dead center.

The purpose of this study is to experimentally investigate in-cylinder flows with cyclic variation in a practical part-loaded two-stroke engine. First, the in-cylinder LDV measurements are introduced, which were carried out above the port layout and the combustion chamber as well as the exhaust pipe or the transfer port together with the simultaneous pressure measurements. Second, the in-cylinder flow characteristics in different combustion groups were discussed. The in-cylinder flow and the combustion-chamber flow were not simply characterized by the pressure variation in the engine or the other passage flow in the exhaust pipe or the transfer port. Finally, the in-cylinder flow structure with three stages was shown using the vector variation analysis and the drawing of the velocity profiles in the engine parts.

The purpose of this study was to detect a misfiring cycle in terms of the transfer-passage and the exhaust-pipe flow rate by experimental measurements. Simultaneous measurements of flow rates and in-cylinder pressure were carried out. The flow rate data were grouped into the different combustion classes by the in-cylinder pressure. A large flow rate of exhaust blow-down and a large reverse flow rate were observed in the cycle before misfiring, compared with in the cycle before firing. It showed that high concentration of the residual burnt gas in the cylinder was the main source of misfiring, this feature was also demonstrated by the complementary measurement of CO and CO2 concentrations.

The velocity variations of the burnt exhaust gas in a practical fired two-stroke engine operating under wide-open-throttle conditions were measured by a fiber LDV ( FLDV ). The characteristics of the exhaust flow are discussed in comparison with those in motoring and in a transfer port. The relation between velocity variation and pressure wave propagation in the exhaust pipe are also investigated. The measured results show that the velocity distribution in the exhaust pipe can be characterized as pulsative flow. The flow characteristics had large influence by the combustion pressure wave propagation. During exhaust and transfer-port opening, the intake flow and the blow-down flow have similar velocity gradient and peak location. The velocity distribution in the exhaust pipe was also measured, which showed pulsative flow variation having no recirculating vortex.

A prototype of measurement device that compresses a sample of engine oil at constant temperature and calculates its void fraction from the magnitude of volume change and pressure was proposed. During compression, the oil sample was pressurized to several hundreds of kPa above atmospheric pressure. Because the gas can be regarded as an ideal gas at this pressure level, the estimation of void fraction can be based on a simple formula derived from the ideal gas law, the law of conservation of mass and Henry’s law. The calibration line is represented by a linear equation of the void fraction, and from the coefficient of void fraction or the constant term the volume fraction of the dissolved gas in the initial state can be known. That is, by experimentally determining the calibration line, not only void fraction but also the volume fraction of the dissolved gas in the initial state can be known. Then, the results of measurement principle confirmation tests were given.