Search Results

In electronic vehicles (EVs) or hybrid electronic vehicles (HEVs), an inverter system has a direct-current-link capacitor (DC-link capacitor) which provides reactive power, attenuates ripple current, reduces the emission of electromagnetic interference, and suppresses voltage spikes. A film capacitor has been used as the DC-link capacitor in high level power system, but the film capacitor's performance has deteriorated over operating time. The decreasing performance of the film capacitor may cause a problem when supplying and delivering energy from the battery to the vehicle's power system. Therefore, the lifetime prediction of the film capacitor could be one of critical factors in the EVs and HEVs. For this reason, the lifetime and reliability of the film capacitor are key factors to show the stability of the vehicle inverter system. There are a lot of methods to predict the lifetime of the film capacitor.

The assessment of the Transmission Loss (TL) of vehicle components at Low-Mid Frequencies generally raises difficulties associated to the physical mechanisms of the noise transmission through the automotive panel. As far as testing is concerned, it is common in the automotive industry to perform double room TL measurements of component baffled cut-outs, while numerical methods are rather applied when prototype or hardware variants are not available. Indeed, in the context of recent efforts for reduction of vehicle prototypes, the use of simulation is constantly challenged to deliver reliable means of decision during virtual design phase. While the Transfer matrix method is commonly and conveniently used at Mid-High frequencies for the calculation of a trimmed panel, the simulation of energy transfer at low frequencies must take into account modal interactions between the vehicle component and the acoustic environment.

In general, when a problem occurs in a component of powertrains, various phenomena appear, and abnormal noise is one of them. The service mechanics diagnose the noise through analysis by using their ears and equipment. However, depending on their experiences, analysis time and diagnostic accuracy vary greatly. To shorten the analysis time and improve the diagnostic accuracy, we have developed a technology to diagnose powertrain parts that cause abnormal noises. To create the best deep learning model for our diagnosis, we tried to collect many abnormal noises from various parts. The collected noise data was measured under idle and various operating conditions from our vehicles and test cells. This noise data is abnormal noises generated from engines, transmissions, drive system and PE (Power Electric) parts of eco-friendly vehicles. From the collected data, we distinguished good and bad data through detailed analysis in time and frequency domain.

An important trend among vehicle NVH engineers is the production of attractive engine acceleration sound quality for the enhancement of a vehicle's image and performance. In addition, customers have increasing interest and enjoyment in customizing their cars to reflect their personal taste and preferences. The PESS (Personalized Engine Sound System) has been developed for making a unique and individually customizable vehicle concept. The system allows the customers an opportunity to create a variety of engine sounds in a single vehicle using active sound design technology. In this system, three different engine sound concepts are pre-defined, Dynamic, Sporty, and Extreme. Each of the engine sounds can then be adjusted with parameters that determine the timbre, such as main order, rumble, and high order. In addition, the pedal position during acceleration has also been used as a parameter to further personalize the experience.

With fuel efficiency becoming an increasingly critical aspect of internal combustion engine (ICE) vehicles, the necessity for research on efficient generation of electric energy has been growing. An energy management (EM) system controls the generation of electric energy using an alternator. This paper presents a strategy for the EM using a control mode switch (CMS) of the alternator for the (ICE) vehicles. This EM recovers the vehicle’s residual kinetic energy to improve the fuel efficiency. The residual kinetic energy occurs when a driver manipulates a vehicle to decelerate. The residual energy is commonly wasted as heat energy of the brake. In such circumstances, the wasted energy can be converted to electric energy by operating an alternator. This conversion can reduce additional fuel consumption. For extended application of the energy conversion, the future duration time of the residual power is exploited. The duration time is derived from the vehicle’s future speed profile.

Impact resistance of plastic underbody parts was studied using simulated injection-molded specimen which can be tested according to different types of material used, injection molding variants like position and number of injection molding gates, and features of ribs. Material applied was glass fiber reinforced polyamide which can be used in underbody parts. Test was performed using several combinations of injection molding gates and rib types. From the test result, optimal design guide for plastic underbody parts was determined. Also, new high impact resistant plastic material made of glass fiber reinforced polyamide 66 (PA66) and polyamide 6 (PA6) alloy was developed and the material properties useful for CAE were determined. As a case study, oil pan and muffler housing were designed following the optimal design guide and CAE. And the reliability of the sample muffler housing designed was verified.

Pressure variation during engine combustion generates torque fluctuation that is delivered through the driveline. Torque fluctuation delivered to the tire shakes the vehicle body and causes the body components to vibrate, resulting in booming noise. HKMC (Hyundai Kia Motor Company)’s TMED (Transmission Mounted Electric Device) type generates booming noises due to increased weight from the addition of customized hybrid parts and the absence of a torque converter. Some of the improvements needed to overcome this weakness include reducing the torsion-damper stiffness, adding dynamic dampers, and moving the operation point of the engine from the optimized point. These modifications have some potential negative impacts such as increased cost and sacrificed fuel economy. Here, we introduce a method of reducing lock-up booming noise in an HEV at low engine speed.

A Light Detection And Ranging (LiDAR) is now becoming an essential sensor for an autonomous vehicle. The LiDAR provides the surrounding environment information of the vehicle in the form of a point cloud. A decision-making system of the autonomous car is able to determine a safe and comfort maneuver by utilizing the detected LiDAR point cloud. The LiDAR points on the cloud are classified as dynamic or static class depending on the movement of the object being detected. If the movement class (dynamic or static) of detected points can be provided by LiDAR, the decision-making system is able to plan the appropriate motion of the autonomous vehicle according to the movement of the object. This paper proposes a real-time process to segment the motion states of LiDAR points. The basic principle of the classification algorithm is to classify the point-wise movement of a target point cloud through the other point clouds and sensor poses.

High-voltage battery system plays a critical role in eco-friendly vehicles due to its effect on the cost and the electric driving range of eco-friendly vehicles. In order to secure the customer pool and the competitiveness of eco-vehicle technology, vehicle electrification requires lowering the battery cost and satisfying the customer needs when driving the vehicles in the real roads, for example, maximizing powers for fun drive, increasing battery capacities for achieving appropriate trip distances, etc. Because these vehicle specifications have a critical effect on the high-voltage battery specification, the key technology of the vehicle electrification is the appropriate decision on the specification of the high-voltage battery system, such as battery capacity and power. These factors affect the size of battery system and vehicle under floor design and also the profitability of the eco-friendly vehicles.

The electrification of the internal combustion engine is an important subject of future automotive technology. By using a motorized internal combustion engine, it is possible to recover waste energy by regeneration technology and to reduce various losses that deteriorate the efficiency of the internal combustion Engine. This paper summarizes the results of the development of an engine-integrated motor that can be applied to a 48V mild hybrid system for motorization of an internal combustion engine. Like the 48V MHSG-mounted mild hybrid system designed to replace the generator in the auxiliary belt system, the motorized internal combustion engine is designed with the scalability as the top priority to minimize the additional space for the vehicle and to mount the same engine in various models.

Automotive manufacturers and engineers have paid attention to promoting engine performance with low emissions satisfying many emission regulations. With such goals in mind, we have investigated new cooling strategies such as high coolant temperature control, fast warm-up and post cooling using an automotive cooling system controlled by electronic actuators. The cooling system in a 2.7 liter HSDI engine was modified for the purpose of this study, and an engine experiment was carried out on a New European Drive Cycle (NEDC). The conventional water pump was decoupled from the engine and electronically controlled by a BLDC motor. Valves were installed at the coolant pathways between the engine and cooling components. Overall, this modification led to a reduction in both fuel consumption and exhaust gas emissions (e.g. THC, CO). The reduction was particularly considerable at the low speed and low load-drive conditions by controlling high temperature of the coolant.

An efficient development environments such as Software-in-the-Loop Simulation (SILS) and Rapid Control Prototyping (RCP) have been widely used to reduce the development time and cost of real-time ECUs. However, conventional SILS does not consider temporal behaviors caused by computation time, task scheduling, network-induced delays, and so on. As a result, the control performance of ECU is likely to be degraded after implementation. To overcome this problem, SILS/RCP which considers the temporal behaviors was suggested in the previous research. In this study, we validated the proposed SILS/RCP environments which are used to design an Electronic Stability Control (ESC) system which is one of the hard real-time control systems. The proposed SILS/RCP environments make it possible to realize ECUs in the early design phase by considering temporal behaviors.

FlexRay is a deterministic and fault-tolerant in-vehicle network(IVN) protocol. It is expected to become a practical standard for automotive communication systems. According to the FlexRay protocol specifications, there are about 60 configurable parameters which should be determined in the design phases. The parameters increase the complexities of FlexRay-based control system development. In this study, we are suggesting a formal design process for FlexRay-based control systems, which is focused on network parameter optimization. We introduce design phases from functional system models to implementations. These phases present formal ways for task allocation, node assignment, network configuration, and implementations. In the network configuration phase, two FlexRay core parameters are selected to optimize network design. Optimal methods of the core parameters provide concise guide lines for optimal communication cycle length and optimal static slot length.

A piston in a diesel engine is subject to the high pressure and the high thermal load. The high structural reliability is required to the piston in the automotive diesel engine and it is important to confirm the design parameters of piston in initial design stage. There are lots of research works proposing new geometries, materials and manufacturing techniques for engine pistons. But, the failures of piston occur frequently in development stage. Failure mechanisms are mainly fatigue related. This paper presents failure mechanisms of the high cycle fatigue and low cycle thermal fatigue cracks which occur on the piston during durability test using engine dynamometer. In this study, FE analysis was carried out to investigate the root cause of piston failure. The analysis includes the FE model of the piston moving system, temperature dependent material properties, mechanical and thermal loadings.

Various polymer-based coatings are applied on piston skirt to reduce friction loss between the piston skirt and cylinder bore which is one of main factors of energy loss in an automotive engine system. These coatings generally consist of polymer binder (PAI) and solid lubricants (graphite or MoS₂) for low friction property. On the other hand, the present study found that PTFE as a solid lubricant and nano diamond as hard particles can be used to improve the low friction and wear resistance simultaneously. In the process of producing coating material, diamond particles pulverized to a nano size tend to agglomerate. To prevent this, silane (silicon coupling agent) treatment was applied. The inorganic functional groups of silane are attached to the nano diamond surface, which keep the diamond particles are apart.

Fuel sloshing noise is involved with flow motion inside fuel tanks as well as structural characteristics of vehicles. Therefore it is necessary to introduce Fluid-Structure Interaction (FSI) analysis to predict sloshing noise phenomena more accurately. Purposes of this paper are to verify the reliability of the FSI method and suggest new CAE analysis processes to predict fuel sloshing noise. The vibration of floor panels induced by sloshing impact is evaluated through FSI analysis. A series of tests is carried out to validate simulation results. The numerical optimization of parameters is also carried out to reduce computation time. In addition, effects of sloshing noise factors are discussed based on simulation and test results. Lastly, a method to predict fuel sloshing noise by exerting sloshing load on a vehicle is suggested.

In this study, the preliminary validation method of the steering system is constructed and the objective is to satisfy the target performance in the conceptual design stage for minimizing the problems after the detailed design. The first consideration about steering system is how to extract the reliable steering effort for parking. The tire model commonly used in MBD(Multi-Body Dynamics) has limited ability to represent deformations under heavy loads. Therefore, it is necessary to study adequate tire model to simulate the behavior due to the large deformation and friction between the ground and the tire. The two approaches related with F tire model and mathematical model are used. The second is how to extract each link’s load in the conceptual design stage. Until now, each link’s load could be derived only by actual vehicle test, and a durability analysis was performed using only pre-settled RIG test conditions.

The software must be verified and optimized from time to time to ensure system performance quality from the development process. Because the later you discover performance issues, the greater the cost of performance improvements, along with the extent to which they are fixed in the source code. In particular, performance problems due to poor system design should be identified and corrected as soon as possible. Also, as development progresses, source code added for new features and modified by bugs can potentially increase system resource usage or worsen responsiveness. Therefore, the development process needs to periodically measure, analyze, and improve system performance. This paper introduces the system-wide performance analyzer and explains how to use it to measure and analyze the performance of the infotainment system for performance management and improvement.

The windshield is an integral part of almost every modern passenger car. Combined with current developments in the automotive industry such as electrification and the integration of lightweight material systems, the reduction of interior noise caused by stochastic and transient wind excitation is deemed to be an increasing challenge for future NVH measures. Active control systems have proven to be a viable alternative compared to traditional passive NVH measures in different areas. However, for windshield actuation there are neither comparative studies nor actually established actuation concepts available to the automotive industry. This paper illustrates a comparative conceptual study on windshield actuation for the active control of wind noise in a passenger car. Making use of an experimental modal analysis of the windshield installed in a medium-sized vehicle, a reduced order numerical simulation model is derived.

A combined experimental and computational study of 3-D unsteady compressible flow in exhaust manifold and CCC system was performed to understand the flow characteristics and to improve the flow distribution of pulsating exhaust gases within monolith. An experimental study was carried out to measure the velocity distribution in production exhaust manifold and CCC under engine operating conditions using LDV (Laser Doppler Velocimetry) system. Velocity characteristics were measured at planes 25 mm away from the front surface of first monolith and between two monolithic bricks. To provide boundary conditions for the computational study, velocity fields according to crank angle were also measured at the entrance of exhaust manifold. The comparisons of exhaust gas flow patterns in the junction and mixing pipe between experimental and computational results were made.