Search Results

Technologies for improving the fuel economy of gasoline engines have been vigorously developed in recent years for the purpose of reducing CO2 emissions. Increasing the compression ratio is an example of a technology for improving the thermal efficiency of gasoline engines. A significant issue of a high compression ratio engine for improving fuel economy and low-end torque is prevention of knocking under a low engine speed. Knocking is caused by autoignition of the air-fuel mixture in the cylinder and seems to be largely affected by heat transfer from the intake port and combustion chamber walls. In this study, the influence of heat transfer from the walls of each part was analyzed by the following three approaches using computational fluid dynamics (CFD) and experiments conducted with a multi-cooling engine system. First, the temperature rise of the air-fuel mixture by heat transfer from each part was analyzed.

This study concerns a dissimilar materials joining technique for aluminum (Al) alloys and steel for the purpose of reducing the vehicle body weight. The tough oxide layer on the Al alloy surface and the ability to control the Fe-Al intermetallic compound (IMC) thickness are issues that have so far complicated the joining of Al alloys and steel. Removing the oxide layer has required a high heat input, resulting in the formation of a thick Fe-Al IMC layer at the joint interface, making it impossible to obtain satisfactory joint strength. To avoid that problem, we propose a unique joining concept that removes the oxide layer at low temperature by using the eutectic reaction between Al in the Al alloy and zinc (Zn) in the coating on galvanized steel (GI) and galvannealed steel (GA). This makes it possible to form a thin, uniform Fe-Al IMC layer at the joint interface. Welded joints of dissimilar materials require anticorrosion performance against electrochemical corrosion.

This study examined methods of machining a microsurface texture on the surface of the rolling elements of a toroidal continuously variable transmission (CVT) for improving the traction coefficient. The microsurface texture of the toroidal surfaces consists of tiny circumferential grooves (referred to here as micro grooves) and a mirror-like surface finish similar to the rolling surface of bearings. Hard turning with a cubic boron nitride (cBN) cutting tool, grinding with a cBN wheel and micro forming were applied to machine the micro grooves. The results made clear the practical potential of each method. A micro forming device was also developed for use in actual production. A mirror-like surface finish and micro crowning of the convex portions of the microsurface texture were simultaneously executed by superfinishing them with a fine-grained elastic superfinishing stone.

In 2006, Nissan began limited leasing of the X-TRAIL FCV equipped with their in-house developed Fuel Cell (FC) stack. Since then, the FC stack has been improved in cost, size, durability and cold start-up capability with the aim of promoting full-scale commercialization of FCVs. However, reduction of cost and size has remained a significant challenge because limited mass transport through the membrane electrode assembly (MEA) has made it difficult to increase the rated current density of the FC. Furthermore, it has been difficult to reduce the variety of FC stack components due to the complex stack configuration. In this study, improvements have been achieved mainly by adopting an advanced MEA to overcome these difficulties. First, the adoption of a new MEA and separators has improved mass transport through the MEA for increased rated current density. Second, an integrated molded frame (IMF) has been adopted as the MEA support.

The use of CAE software in developing plastic components has advanced rapidly in recent years. This progress has been supported by the development of practical analytical tools, based on the finite element and boundary element methods, and on the dramatic improvements seen in computer performance. Following the introduction of a flow analysis program in 1982, Nissan has developed and implemented advanced programs for use in developing plastic components and has integrated the programs into a unified in-house system. This system is being utilized at the design and manufacturing stages of interior and exterior trim parts and has produced concrete results in different phases of component development. Work is now proceeding on the development of a system that can simultaneously analyze both the component performance and the factors that need to be considered in the manufacturing process.

The ways in which vehicles are used in the field are continually becoming more diverse. In order to provide the optimum solution with respect to performance and weight, it is necessary to be able to assure vehicle endurance reliability with a high degree of accuracy in relation to the manner of use in each market. This situation has increased the importance of accurately quantifying the ways in which vehicles are used in the field and of designing vehicles with sufficient endurance reliability to match the usage requirements. This report presents a “market model” by which the manner of usage in the field can be treated quantitatively using combinations of environmental factors that influence the road load, drive load and corrosion load, representing typical loads vehicles must withstand.

The purpose of this study is to clarify the state of heat loss to the cylinder liner of the tested engine of which piston and cylinder head were previously measured. The authors' group developed an original measurement technique of instantaneous surface temperature at the cylinder liner wall using thin-film thermocouples. The temperature was measured at 36 points in total. The instantaneous heat flux was calculated by heat transfer analysis using measurement results of the temperature at the wall. As a result, the heat loss ratio to all combustion chamber walls is evaluated except the intake and exhaust valves.

The SR engine is a new medium-size, all aluminum (cylinder block, head, rocker cover and oil pan) in-line 4-cylinder gasoline powerplant developed as a replacement for CA engine in Nissan's compact passenger cars. The development aim set for this engine was to achieve excellent power output and ample torque in the middle-and high-speed ranges, as well as a clear, linear engine sound up to the red zone. These performance targets have been achieved through the use of the 4-valve-per-cylinder DOHC design featuring a Y-shaped valve rocker arm system. This system allows a straight intake port for high power output and a narrow valve angle for a compact combustion chamber. The result is ample torque output as well as good fuel economy.

In general, the improvement of vehicle body stiffness involves a trade-off with the body weight. The objective of this research is to derive the lightest-weight solution from the original vehicle model by finding the optimized spot-weld layout and body panel thickness, while keeping the body stiffness and number of spot welds constant. As the first step, a method of deriving the optimal layout of spot welds for maximizing body stiffness was developed by applying the topology optimization method. While this method is generally used in shape optimization of continuous solid structures, it was applied to discontinuous spot-weld positions in this work. As a result, the effect of the spot-weld layout on body stiffness was clarified. In the case of the body used for this research, body stiffness was improved by about 10% with respect to torsion and vertical and lateral bending.

This paper describes a low-cost 48 × 48 element thermal imaging camera intended for use in measuring the temperature in a car interior for advanced air conditioning systems. The compact camera measures 46 × 46 × 60 mm. It operates under a program stored in the central processing unit and can measure the interior temperature distribution with an accuracy of ±0.7°C in range from 0 to 40°C. The camera includes a thermoelectric focal plane array (FPA) housed in a low-cost vacuum-sealed package. The FPA is fabricated with the conventional IC manufacturing process and micromachining technology. The chip is 6.5 × 6.5 mm in size and achieves high sensitivity of 4,300 V/W, which is higher than the performance reported for any other thermopile. This high performance has been achieved by optimizing the sensor's thermal isolation structure and a precisely patterned Au-black absorber that attains high infrared absorptivity of more than 90%.

A new multidimensional calculation method has been developed to simulate the warm-up characteristics of close-coupled catalytic converter systems. First, a one-dimensional gas exchange simulation and a three-dimensional exhaust gas flow calculation are combined to simulate the pulsation gas flow caused by the gas exchange process. The gas flow calculation and a heat transfer calculation are then combined to simulate heat transfer in the exhaust manifold and the catalyst honeycomb under pulsation flow. The predicted warm-up characteristics of the systems examined agreed well with the experimental data. In this simulation, CPU time was reduced greatly through the use of new calculation methods. Finally, the warm-up process of close-coupled catalysts is analyzed in detail with this simulation method. The design requirements for improving warm-up characteristics have been made clear.

The International Lubricant Standardization and Approval Committee (ILSAC) ATF subcommittee members have compared the two oxidation bench test methods, Aluminum Beaker Oxidation Test (ABOT) and Indiana Stirring Oxidation Stability Test (ISOT), using a number of factory-fill and service-fill ATFs obtained in Japan and in the US. In many cases, the ATFs were more severely oxidized after the ABOT procedure than after the same duration of the ISOT procedure. The relative severity of these two tests was influenced by the composition of the ATFs. The bench test oxidation data were compared with the transmission and the vehicle oxidation test data.

Recently tailored blank sheets are widely and very often applied to car body's panels in order to reduce weight and number of automobile parts. The tailored blank sheets are produced by welding more than two metal sheets. The gap between edges of blank sheets before laser welding should be controlled for obtaining good quality tailored blank sheets. Therefore control of gap within 0.1mm between batting two blank sheets for production is one of main subjects for producing tailored blank sheets. This report presents not only a new mechanism on gap control but also a development of Finite Element Method (FEM) analysis for prediction of gap. The new mechanism has been applied successfully to produce good quality tailored blank sheets. The gap prediction simulation can reduce the time for gap control apparatus design.

A plastic intake manifold has been developed for the new QR engine. This manifold has an intricate shape owing to its performance and layout requirements. The die slide injection (DSI) method was selected to manufacture this complicated shape using the world's first application of a common mold forming technique for a three-piece structure. This paper describes the manufacturing technology and the measures adopted to ensure the strength of welded parts, which is a key point of this method. The benefits obtained by applying this plastic intake manifold to the new engine are also described.

Hydrofrorming is an efficient forming process to produce automotive parts for reducing weight of cars. In order to reduce the period of development of hydrofoming parts, numerical simulation using FEM is applied to evaluate formability. A pipe needs to be bent before hydroforming for forming complicated shape parts. A pipe bending process is also necessary to FEM simulation. In this paper, a highly effective method to create a bent pipe FEM model based on geometrical changing between a pipe before and after bending is proposed. The widely used draw bending process is supposed to be applied. The method can construct the model in a short time. Therefore total computation time can be reduced drastically. The effects of number of integration points and elements to the computed results and springback prediction after bending are also investigated. The proposed method are applied to a actual part, the computed results are in good agreement with the experimental results.

A combined computational fluid dynamics (CFD) and finite element (FE) analysis approach has been developed to simulate in the early stages of design the temperature distribution and estimate the thermal fatigue life of an engine exhaust manifold. To simulate the temperature distribution under actual operating conditions, we considered the external and internal flow fields. Digital mock-ups of the vehicle and engine were used to define the geometry of the engine compartment. External-air-flow simulation using in-house CFD code was used to predict the flow fields in the engine compartment and the heat transfer coefficients between the air and the exhaust manifold wall at various vehicle speeds. Unsteady-gas-flow calculation using the STAR-CD thermal- fluids analysis code was to predict the heat transfer coefficients between the exhaust gas and the manifold wall under various operating conditions.

Car makers are working hard today to shorten development and production lead times through the use of flexibile manufacturing systems(FMSs)to meet diversified and individualized customer requirements. To achieve this goal, Nissan has been developing many kinds of new technologies and systems such as: (1) the intelligent body assembly system for body assembly processes; (2) a press die stamping simulation method and unified database for press die manufacturing; (3) a robot and facility teaching system using CAD data; (4) an automated assembly line for trim and chassis assembly operations. These new FMS methods have been implemented in many manufacturing areas, including the stamping shop, body assembly shop, painting shop and trim and chassis shop. This paper focuses mainly on the intelligent body assembly system as a typical example of the new production systems and technologies being developed at Nissan.

Eliminating squeal noise generated during braking is an important task for the improvement of vehicle passengers' comfort. Considerable amount of research and development works have been done on the problem to date. In this study, we focused on the analyses of friction self-excited vibration and brake part resonance during high frequency brake squeal. Friction self-excited vibration is caused by the dry friction between pads and rotor, and occurs as a function of their relative sliding velocities. Its vibration frequency can be calculated in relation to the mass and stiffness of the pad sliding surface. Frequency responses of the brake assembly were measured and the vibration modes of the pad, disc and caliper during squeal were identified through modal analysis. Further study led to the development of a computer simulation method for analyzing the vibration modes of brake parts. Analytical results obtained using the method agreed well with the corresponding experimental data.

This paper describes a new 4.5-liter V8 engine, VH45DE, which was developed for use in the INFINITI Q45 sporty luxury sedan that was released in the U.S. and Japanese markets in November 1989. The many V8 engines in use around the world can be broadly devided into two categories. One category is characterized by ample torque at low engine speed and relatively large engine displacement. The other category is characterized by enhanced performance at relatively high engine speeds. The VH45DE engine is a new-generation V8 powerplant that delivers smooth power output at top-end speed and also generates ample torque at low engine speed to maintain good idle stability, and accomplishes it all with the smallest possible displacement. Development efforts were focused on two main goals. The first was to achieve efficient intake air charging. This has been accomplished the intake air resonant point at a relatively high engine speed through appropriate intake branch and collector tuning.

Use of high strength steel (HSS) could be an important consideration in achieving competitive weight and safety performance of the body-in-white (BIW). This study covers key technical issues in the application development. Many aspects were studied such as formability, weldability and impact strength for application of this grade to the BIW. One of the key issues is spot weldability, especially in the assembly of heavy gauge materials for structural parts. The spot weld strength appears not to satisfy the target for some HSS applications, when hardness of the nugget is high. The relation between weld strength and the chemical composition of steel sheets was studied, because hardness can be controlled by chemical composition and welding conditions. It was found that using lower carbon content or carbon equivalent compared to conventional grades could improve weld strength.