Search Results

Chassis dynamometer tests were conducted on three Class III on-highway motorcycles produced for the North American market and equipped with advanced emission control technologies in order to inform emissions inventories and compare the impacts of existing Tier 2 (E0) fuel with more market representative Tier 3 and LEV III certification fuels with 10% ethanol. For this study, the motorcycles were tested over the US Federal Test Procedure (FTP) and the World Motorcycle Test Cycle (WMTC) certification test cycles as well as a sample of real-world motorcycle driving informally referred to as the Real World Driving Cycle (RWDC). The primary interest was to understand the emissions changes of the selected motorcycles with the use of certification fuels containing 10% ethanol compared to 0% ethanol over the three test cycles.

With ongoing concerns about the elevated levels of ambient air pollution in urban areas and the contribution from heavy-duty diesel vehicles, hybrid electric vehicles are considered as a potential solution as they are perceived to be more fuel efficient and less polluting than their conventional engine counterparts. However, recent studies have shown that real-world emissions may be substantially higher than those measured in the laboratory, mainly due to operating conditions that are not fully accounted for in dynamometer test cycles. At the U.S. EPA National Fuel and Vehicle Emissions Laboratory (NVFEL) the in-use criteria emissions and energy efficiency of heavy-duty class 8 vehicles (up to 36280 kg) can be evaluated under controlled conditions in the heavy-duty chassis dynamometer test.

Motor vehicle emission testing during on-road driving is important to assess a vehicle’s exhaust emission control design, its compliance with Federal regulations and its impact on air quality. The U.S. Environmental Protection Agency (EPA) has been developing new approaches to screen the characteristics of vehicle dynamic emission control behaviors (its operating signature) while driving both on-road and on-dynamometer. The so-called “signature device” used for this testing is equipped with an O2/NOx sensor, thermocouple and GPS to record dynamic exhaust NOx concentration, air fuel ratio-controlled tailpipe lambda (λ), tailpipe temperature and vehicle speed (acceleration). In the early EPA research, signature screening was used to characterize a vehicle’s PCM control behaviors (cause/effect bijectivity), which help distinguish operation in normal control state-space and abnormal state-space.

This paper summarizes the Heavy-Duty In-Use Testing (HDUIT) measurement allowance program for Particulate Matter Portable Emissions Measurement Systems (PM-PEMS). The measurement allowance program was designed to determine the incremental error between PM measurements using the laboratory constant volume sampler (CVS) filter method and in-use testing with a PEMS. Two independent PM-PEMS that included the Sensors Portable Particulate Measuring Device (PPMD) and the Horiba Transient Particulate Matter (TRPM) were used in this program. An additional instrument that included the AVL Micro Soot Sensor (MSS) was used in conjunction with the Sensors PPMD to be considered a PM-PEMS. A series of steady state and transient tests were performed in a 40 CFR Part 1065 compliant engine dynamometer test cell using a 2007 on-highway heavy-duty diesel engine to quantify the accuracy and precision of the PEMS in comparison with the CVS filter-based method.

Chassis dynamometer testing was conducted with three on-highway motorcycles produced for the North American market with engine displacements of 296 cc, 749 cc and 1198 cc to better inform criteria pollutant emissions inventories. The motorcycles were tested using US Tier 2 certification fuel over the Federal Test Procedure (FTP), World Motorcycle Test Cycle (WMTC) and a cycle based on a sample of real-world motorcycle driving, informally referred to as the ‘Real World Driving Cycle’ (RWDC). Emissions characterization includes composite, individual test phase and 1Hz cumulative results for various criteria pollutants for each test cycle. Overall, it was found that the higher peak speed rates and peak torque levels observed during the RWDC are more fully represented in the WMTC than the FTP. The use of the WMTC and RWDC cycles generally translated into higher emissions rates compared to the FTP and in particular for nitrogen oxides and carbon monoxide.

Homogenous charge compression ignition (HCCI) engines offer a great potential in achieving high thermal efficiency and extremely low NOx at the same time. However, control of combustion phasing over a wide speed and load range has been a challenge, especially during transient operations. This paper describes work conducted at the National Vehicle and Fuel Emissions Laboratory, which explores the potential use of an HCCI engine as a power plant for a hybrid vehicle. A four-cylinder, 1.9 L commercial diesel engine was modified to operate with port-injected regular grade gasoline in HCCI mode. The combustion phasing is controlled by a combination of boost, EGR and thermal management as a function of engine speed and load. As a stand-alone unit, the engine has demonstrated a wide operation range with efficiency like that of a diesel engine and NOx below 0.2 g/kWh. At room temperature, the engine starts in SI mode and then transitions to HCCI in about 25 seconds.

In-use, light-duty vehicles were recruited in Cary, North Carolina for emissions testing on a transportable dynamometer in 1999. Two hundred forty-eight vehicles were tested in as received condition using the IM240 driving cycle. The study was conducted in two phases, a summer and winter phase, with half of the vehicles recruited during each phase. Regulated emissions, PM10, carbonaceous PM, aldehydes and ketones were measured for every test. PM2.5, individual volatile hydrocarbons, polycyclic aromatic hydrocarbons, sterane and hopane emissions were measured from a subset of the vehicles. Average light-duty gasoline PM10 emission rates increased from 6.5 mg/mi for 1993-97 vehicles to 53.8 mg/mi for the pre-1985 vehicles. The recruited fleet average, hot-stabilized IM240 PM10 emission rate for gasoline vehicles was 19.0 mg/mi.

This paper covers work performed for the California Air Resources Board and US Environmental Protection Agency by Southwest Research Institute. Emission measurements were made on four in-use off-road two-stroke motorcycles and all-terrain vehicles utilizing oxygenated and non-oxygenated fuels. Emission data was produced to augment ARB and EPA's off-road emission inventory. It was intended that this program provide ARB and EPA with emission test results they require for atmospheric modeling. The paper describes the equipment and engines tested, test procedures, emissions sampling methodologies, and emissions analytical techniques. Fuels used in the study are described, along with the emissions characterization results. The fuel effects on exhaust emissions and operation due to ethanol content and fuel components is compared.

This study is the second in a series of three EPA studies to investigate the effect of fuel reformulations and modifications on exhaust emissions. Both the first and second study in this series of studies were used to support the development of EPA's complex model for the certification of reformulated gasolines. Phase I of the study tested eight fuels on forty vehicles. This study, termed Phase II, tested twelve fuels on a separate fleet of 39 light-duty vehicles. The Phase II fuel parameters studied included Reid Vapor Pressure (RVP), the 50% and 90% evaporated distillation temperatures (T50 and T90), sulfur content, aromatics content, olefin content, oxygenate type and oxygen content. Measured exhaust emissions included total hydrocarbons (THC), oxides of nitrogen (NOx), carbon monoxide (CO), carbon dioxide (CO2), benzene, 1,3-butadiene, acetaldehyde and formaldehyde.

This study was the first of three EPA studies to investigate the effect of gasoline fuel parameters on hydrocarbon, nonmethane hydrocarbon, nitrogen oxides, benzene, formaldehyde, and acetaldehyde exhaust emissions of 1990 model year or equivalent vehicles. The fuel parameters tested in this program were oxygen concentration, Reid Vapor Pressure (RVP), ninety percent evaporative distillation temperature (T90), and sulfur concentration. Sulfur concentration was found to have the greatest effect on hydrocarbon and nitrogen oxide emissions. Increasing oxygen concentration and RVP reduction was found to reduce hydrocarbon emission more for high-emitting than normal-emitting vehicles. Oxygenate concentration was found to have a significant effect on aldehyde emissions.

Fourier Transform Infrared Spectroscopy (FT-IR) has been used to measure the exhaust emissions from vehicles during standard driving tests. Comparisons with conventional analyzers for modal tests have been made for the regulated species such as carbon monoxide (CO), nitrogen oxides (NOx) and total hydrocarbon (THC). The concentrations of methane, methanol and formaldehyde were also measured at one second time intervals during several driving tests. The average concentration values for these species were compared to the bag samples for several tests. Modal concentration curves were also calculated for MTBE, ETBE and several other species of interest. The results indicate FT-IR can be used for making modal measurements on the regulated species and non-regulated species in vehicle exhaust emissions. Several studies were performed to evaluate the long-term stability and sensitivity of FT-IR in actual test situations.

Portable Emission Measurement Systems (PEMS) are used by the U.S. Environmental Protection Agency (EPA) to measure gaseous and particulate mass emissions from vehicles in normal, in-use, on-the-road operation to support many of its programs, including assessing mobile source emissions compliance, emissions factor assessment for in-use fleet modeling, and collection of in-use vehicle operational data to support vehicle simulation modeling programs. This paper discusses EPA’s use of Global Positioning System (GPS) measured altitude data and electronically logged vehicle speed data to provide real-world road grade data for use as an input into the Gamma Technologies GT-DRIVE+ vehicle model. The GPS measured altitudes and the CAN vehicle speed data were filtered and smoothed to calculate the road grades by using open-source Python code and associated packages.