Search Results

Gasoline turbocharged direct injection (GTDI) engines, such as EcoBoost™ from Ford, are becoming established as a high value technology solution to improve passenger car and light truck fuel economy. Due to their high specific performance and excellent low-speed torque, improved fuel economy can be realized due to downsizing and downspeeding without sacrificing performance and driveability while meeting the most stringent future emissions standards with an inexpensive three-way catalyst. A logical and synergistic extension of the EcoBoost™ strategy is the use of E85 (approximately 85% ethanol and 15% gasoline) for knock mitigation. Direct injection of E85 is very effective in suppressing knock due to ethanol's high heat of vaporization - which increases the charge cooling benefit of direct injection - and inherently high octane rating. As a result, higher boost levels can be achieved while maintaining optimal combustion phasing giving high thermal efficiency.

Piston temperature plays a major role in determining details of fuel spray vaporization, fuel film deposition and the resulting combustion in direct-injection engines. Due to different heat transfer properties that occur in optical and all-metal engines, it becomes an inevitable requirement to verify the piston temperatures in both engine configurations before carrying out optical engine studies. A novel Spot Infrared-based Temperature (SIR-T) technique was developed to measure the piston window temperature in an optical engine. Chromium spots of 200 nm thickness were vacuum-arc deposited at different locations on a sapphire window. An infrared (IR) camera was used to record the intensity of radiation emitted by the deposited spots. From a set of calibration experiments, a relation was established between the IR camera measurements of these spots and the surface temperature measured by a thermocouple.

An experimental study is performed to investigate the effects of charge motion control on in-cylinder fuel-air mixture preparation and combustion inside a direct-injection spark-ignition engine with optical access to the cylinder. High-pressure production injector is used with fuel pressures of 5 and 10 MPa. Three different geometries of charge motion control (CMC) device are considered; two are expected to enhance the swirl motion inside the engine cylinder whereas the third one is expected to enhance the tumble motion. Experiments are performed at 1500 rpm engine speed with the variation in fuel injection timing, fuel pressure and the number of injections. It is found that swirl-type CMC devices significantly enhance the fuel-air mixing inside the engine cylinder with slower spray tip penetration than that of the baseline case without CMC device. Combustion images show that the flame growth is faster with CMC device compared to the similar case without CMC device.

This study focuses on the combustion visualization of spark ignition combustion in an optical single cylinder engine using natural gas and propane at several air to fuel ratios and speed-load operating points. Propane and natural gas fuels were compared as they are the most promising gaseous alternative fuels for reciprocating powertrains, with both fuels beginning to find wide market penetration on the fleet level across many regions of the world. Additionally, when compared to gasoline, these gaseous fuels are affordable, have high knock resistance and relatively low carbon content and they do not suffer from the complex re-fueling and storage problems associated with hydrogen.

Surface coatings are one of the most widely used routes to enhance the tribological properties of cylinder kits due to effective sealing capability with low friction coefficient and high wear resistance. In the current study, we have conducted the surface texture characterization of the coating on piston skirts and evaluated the impact of a novel Abradable Powder Coating (APC) on cylinder-kit performance in comparison to stock pistons. The surface texture and characteristic properties varying across the piston skirt are obtained and analyzed via a 3D optical profiler and OmniSurf3D software. The engine operating conditions are found through a combination of measurements, testing, and a calibrated GT-Power model. The variable surface properties along with other dimensions, thermodynamic attributes, flow characteristics and material properties are used to build a model in CASE (Cylinder-kit Analysis System for Engines)- PISTON for both an APC coated piston and a stock piston.

Homogeneous Charge Compression Ignition (HCCI) combustion has the potential to produce low NOx and low particulate matter (PM) emissions while providing high efficiency. In HCCI combustion, the start of auto-ignition of premixed fuel and air depends on temperature, pressure, concentration history during the compression stroke, and the unique reaction kinetics of the fuel/air mixture. For these reasons, the choice of fuel has a significant impact on both engine design and control strategies. In this paper, ten (10) gasoline-like testing fuels, statistically representative of blends of four blending streams that spanned the ranges of selected fuel properties, were tested in a single cylinder engine equipped with a hydraulic variable valve train (VVT) and gasoline direct injection (GDI) system.

In developing a direct injection gasoline engine, the in-cylinder fuel air mixing is key to good performance and emissions. High speed visualization in an optically accessible single cylinder engine for direct injection gasoline engine applications is an effective tool to reveal the fuel spray pattern effect on mixture formation The fuel injectors in this study employ the unique multi-hole turbulence nozzles in a PFI-like (Port Fuel Injection) fuel system architecture specifically developed as a Low Pressure Direct Injection (LPDI) fuel injection system. In this study, three injector sprays with a narrow 40° spray angle, a 60°spray angle with 5°offset angle, and a wide 80° spray angle with 10° offset angle were evaluated. Image processing algorithms were developed to analyze the nature of in-cylinder fuel-air mixing and the extent of fuel spray impingement on the cylinder wall.

The requirement of reduced emissions and improved fuel economy led the introduction of direct-injection (DI) spark-ignited (SI) engines. Dual-fuel injection system (direct-injection and port-fuel-injection (PFI)) was also used to improve engine performance at high load and speed. Ethanol is one of the several alternative transportation fuels considered for replacing fossil fuels such as gasoline and diesel. Ethanol offers high octane quality but with lower energy density than fossil fuels. This paper presents the combustion characteristics of a single cylinder dual-fuel injection SI engine with the following fueling cases: a) gasoline for PFI and DI, b) PFI gasoline and DI ethanol, and c) PFI ethanol and DI gasoline. For this study, the DI fueling portion varied from 0 to 100 percentage of the total fueling over different engine operational conditions while the engine air-to-fuel ratio remained at a constant level.

An experimental study is performed to investigate the fuel impingement on cylinder walls and piston top inside a direct-injection spark-ignition engine with optical access to the cylinder. Three different fuels, namely, E85, E50 and gasoline are used in this work. E85 represents a blend of 85 percent ethanol and 15 percent gasoline by volume. Experiments are performed at different load conditions with the engine speeds of 1500 and 2000 rpm. Two types of fuel injectors are used; (i) High-pressure production injector with fuel pressures of 5 and 10 MPa, and (ii) Low-pressure production-intent injector with fuel pressure of 3 MPa. In addition, the effects of split injection are also presented and compared with the similar cases of single injection by maintaining the same amount of fuel for the stoichiometric condition. Novel image processing algorithms are developed to analyze the fuel impingement quantitatively on cylinder walls and piston top inside the engine cylinder.

The paper is based on the premise that the sole purpose of combustion in piston engines is to generate pressure for pushing the expansion process away from the compression process (both expressed in terms of appropriate polytropes) to create a work producing cycle. This essential process, referred to as the dynamic stage of combustion, is carved out of the cycle and its salient properties deduced from the measured pressure profile, as a solution of an inverse problem: deduction of information on an action from its outcome. An analytical technique, construed for this purpose, is first presented and, then, applied to a direct injection, spark-ignition, methanol fueled four-stroke engine.

The sole purpose of combustion in a piston engine is to generate pressure in order to push the piston and produce work. Pressure diagnostics provides means to deduce data on the execution of the exothermic process of combustion in an engine cylinder from a measured pressure profile. Its task is that of an inverse problem: evaluation of the mechanism of a system from its measured output. The dynamic properties of the closed system in a piston engine are expressed in terms of a dynamic stage - the transition between the processes of compression and expansion. All the phenomena taking place in its course were analyzed in the predecessor of this paper, SAE 2002-01-0998. Here, on one hand, its concept is restricted to the purely dynamic effects, while on the other, the transformation of system components, taking place in the course of the exothermic chemical reaction to raise pressure, are taken into account by the exothermic stage.

In recent years, more attention has been focused on environment pollution and energy source issues. As a result, increasingly stringent fuel consumption and emission legislations have been implemented all over the world. For automakers, enhancing engine’s efficiency as a must contributes to lower vehicle fuel consumption. To reach this goal, Geely auto started the development of a 3-cylinder 1.0L turbocharged direct injection (TGDI) gasoline engine to achieve a challenging fuel economy target while maintaining fun-to-drive and NVH performance. Demanding development targets for performance (specific torque 205Nm/L and specific power 100kW/L) and excellent part-load BSFC were defined, which lead to a major challenge for the design of engine systems, especially for combustion system.

In recent years, more attention has been focused on environment pollution and energy source issues. As a result, increasingly stringent fuel consumption and emission legislations have been implemented all over the world. For automakers, enhancing engine’s efficiency as a must contributes to lower vehicle fuel consumption. To reach this goal, Geely auto started the development of a 3-cylinder 1.0L turbocharged direct injection (TGDI) gasoline engine to achieve a challenging fuel economy target while maintaining fun-to-drive and NVH performance. Demanding development targets for performance (specific torque 205Nm/L and specific power 100kW/L) and excellent part-load BSFC were defined, which lead to a major challenge for the design of the combustion system. Considering air/fuel mixture, fuel wall impingement and even future potential for lean burn combustion, a symmetrical layout and a central position for the injector with 200bar injection pressure was determined.

In this paper comparisons were made between the fuel economy improvement between a High Pressure loop (HP) water-cooled Exhaust Gas Recirculation (EGR) system and a Low Pressure loop (LP) water-cooled EGR system. Experiments were implemented on a 1.3-Litre turbocharged PFI gasoline engine in two pars. One was EGR rate as single operating point to compare the different effect of HP- and LP-EGR. The other was mini map from 1500rpm to 3000rpm and BMEP from 2bar to 14bar because of the relative narrow available range of HP-EGR system. In consideration of practical application of EGR system, the coolant used in this experiment was kept almost the same temperature as in real vehicles (88±3°C) instead of underground water temperature, besides a model was built to calculate constant volume ratio (CVR). The results indicated that the effect of HP-EGR was weaker than that of LP-EGR under the same EGR rate, which could be seen from change of combustion parameters.

This research was concerned with the use of Exhaust Gas Recirculation (EGR) improving the fuel economy over a wide operating range in a downsized boosted gasoline engine. The experiments were performed in a 1.3-Litre turbocharged PFI gasoline engine, equipped with a Low Pressure (LP) water-cooled EGR system. The operating conditions varied from 1500rpm to 4000rpm and BMEP from 2bar to 17bar. Meanwhile, the engine’s typical operating points in NEDC cycle were tested separately. The compression ratio was also changed from 9.5 to 10.5 to pursue a higher thermal efficiency. A pre-compressor throttle was used in the experiment working together with the EGR loop to keep enough EGR rate over a large area of the engine speed and load map. The results indicated that, combined with a higher compression ratio, the LP-EGR could help to reduce the BSFC by 9∼12% at high-load region and 3∼5% at low-load region.

Intake charge preparation has strong effects on HCCI combustion, especially on the start of ignition. In this paper, the influence of different intake charge preparation modes on HCCI combustion in a single cylinder engine equipped with a hydraulic variable valve train (VVT) and gasoline direct injection (GDI) system is studied. By using VVT and GDI, three different intake charge preparation modes are implemented: re-compression early injection (RCEI), re-compression split injection (RCSI), and re-breathing early injection (RBEI). For each intake charge preparation mode, three engine operating conditions are investigated: 1.5 bar IMEP at 1000 rpm, 3 bar IMEP at 2000 rpm, and 6 bar/deg of maximum rate of pressure rise at 3000 rpm (IMEP's very near 3 bar). For all engine operating conditions and intake charge preparation modes, the combustion phasing, represented by the 50% mass fraction burned location (CA50), were fixed at 5 degrees after top dead center.

To meet more stringent emission regulations for diesel engines, diesel particulate filters (DPF) have been widely used for diesel engines. However, the DPF regeneration is a great challenge for fuel economy. In this paper, a mathematical model characterizing the microwave regeneration process of a wall-flow particulate filter is introduced to better understand the process. Based on this model, important parameters such as evolutions of the energy stream densities of microwaves, wall temperature, regeneration efficiency and the pressure drop in the filters, both cordierite and SiC, are investigated. These results can provide an important theoretical guide for optimizing and controlling the microwave regeneration process.

A direct-injection and spark-ignition single-cylinder engine with optical access to the cylinder was used for the combustion visualization study. Gasoline and ethanol-gasoline blended fuels were used in this investigation. Experiments were conducted to investigate the effects of fuel injection pressure, injection timing and the number of injections on the in-cylinder combustion process. Two types of direct fuel injectors were used; (i) high-pressure production injector with fuel pressures of 5 and 10 MPa, and (ii) low-pressure production-intent injector with fuel pressure of 3 MPa. Experiments were performed at 1500 rpm engine speed with partial load. In-cylinder pressure signals were recorded for the combustion analyses and synchronized with the high-speed combustion imaging recording. Visualization results show that the flame growth is faster with the increment of fuel injection pressure.

Numerical simulation has been widely used in the engine development process to improve the development quality, especially in the area of in-cylinder flow and fuel evaporation. In this paper, a fuel spray model for a gasoline direct injection (GDI) engine, calibrated against spray visualization in a spray bomb, is developed to characterize the fuel spray atomization, vaporization, and interaction with in-cylinder air flow. With this model, fuel atomization and fuel-air mixing process are thoroughly analyzed at full load operating conditions at both low and high speeds. It is shown that fuel spray at high speed is deflected towards intake side, leading to limited wall wetting, piston wetting, and good vaporization, due to intensive tumble flow and high temperature. The results from the numerical simulation provide important guideline for the development of a GDI engine.

Extensive experimental and numerical investigations with respect to mass balance unit (MBU) were reported to improve the vibration and acoustic performance for inline 4-cylinder engine due to unbalanced inherent secondary order inertial forces. Design of gear-driven MBU with two parallel shafts and two gear pairs which was positioned beneath the crankshaft would be described in the paper. For the sake of compact package and reliable design, the driving gear ring of the system was shrink fitted onto the crankweb, and issues such as lubrication, strength, assembly were taken into account during design process. As a result, 93.66% of 2nd order mass force balance was achieved and2nd vibration level of engine was decreased remarkably. However, acoustical behavior was deteriorated due to gear impact and rattle at the engagement. Extra efforts were paid to solve the unpleasant noise through internal and external excitation optimizations.