Search Results

A quasidimensional engine simulation which uses the concepts of fractal geometry to model the effects of turbulence on flame propagation in a homogeneous charge SI engine has been developed. Heat transfer and blowby/crevice flow submodels are included in this code and the submodels chosen are found to be reasonable. The model predictions of cylinder pressure histories are then compared with experimental data over a range of loads, equivalence ratios, and engine speeds. The model is not adjusted in any manner to yield better agreement with the data, other than by tuning the simple turbulence model used so as to yield agreement with data for the nonreacting flow. However, current information about the flame wrinkling scales in an engine is inadequate. Therefore, predictions are made for three different assumptions about the flame wrinkling scales which span the range of physically possible scales.

Initial investigations of a new type of high energy ignitor for I.C. engines are described. The ignitor is a miniaturized railgun, or “railplug.” The railplug produces a relatively large mass of high velocity plasma. These characteristics may be advantageous for initiating combustion in a number of different applications. Unlike a plasma jet ignitor, the railplug plasma is driven not only by thermodynamic expansion, but by electromagnetic forces as well. Four experimental railplug designs were evaluated using schlieren and shadowgraphy visualization to examine plasma movement and shape. Railplug current and voltage were also measured. One railplug consisting of two unenclosed parallel rails was used to demonstrate the electromagnetically induced motion of the plasma at ambient conditions. Schlieren photos showed that the plasma plume moves strongly in the direction of the electromagnetic Lorentz forces.

Condensation of fuel vapor on the cold surfaces within the combustion chamber is investigated as a possible mechanism for increased HC emissions from SI engines during cold start. A one-dimensional, transient, mass diffusion analysis is used to examine the condensation of single-species fuels on the surfaces of the combustion chamber as the pressure within the cylinder rises during compression and combustion, and re-vaporization during expansion, blowdown, and exhaust. The effects of wall temperature, fuel volatility, and engine load and speed on this mechanism are also discussed. This analysis shows that low-volatility fuel components can condense on the surfaces of the combustion chamber when the surface temperatures are sufficiently low. This condensed fuel may re-vaporize during the power and exhaust strokes, or it may remain in the combustion chamber until surface temperatures rise, perhaps tens of seconds later.

A liquid-phase port injection system for liquefied petroleum gas (LPG) generally consists of a fuel storage tank with extended capability of operating up to 600 psi, a fuel pump, and suitable fuel lines to and from the LPG fuel injectors mounted in the fuel rail manifold. Port injection of LPG in the liquid phase is attractive due to engine emissions and performance benefits. However, maintaining the LPG in the liquid phase at under-hood conditions and re-starting after hot soak can be difficult. Multiphase behavior within a liquid-phase LPG injection system was investigated computationally and experimentally. A commercial chemical equilibrium code (ASPEN PLUS™) was used to model various LPG compositions under operating conditions.

Combustion chamber pressure measurement in engines via a passage is an old technique that is still widely used in engine research. This paper presents improved passage designs for an off-set electrode spark plug designed to accept a pressure transducer. The spark plug studied was the Champion model 304-063A. Two acoustic models were developed to compute the resonance characteristics. The new designs have a resonance frequency in a range higher than the fundamental frequency expected from knock so that the signal can be lowpass filtered to remove the resonance and not interfere with pressure signal components associated with combustion phenomena. Engine experiments verified the spark plug resonance behavior. For the baseline engine operating condition approximately 50 of 100 cycles had visible passage resonance in the measured pressure traces, at an average frequency of 8.03 kHz.

The Texas Project was a multi-year study of aftermarket conversions of a variety of light-duty vehicles to CNG or LPG. Emissions and fuel economy when using these fuels are compared to the results for the same vehicles operating on certification gasoline and Federal Phase 1 RFG. Since 1993, 1,040 tests were conducted on 10 models, totally 86 light-duty vehicles. The potential for each vehicle model/kit combination to attain LEV certification was assessed. Also, comparisons of emissions and fuel economy between converted vehicles when operating on gasoline and nominally identical un-converted gasoline control vehicles were analyzed. Additional evaluations were performed for a subfleet that was subjected to exhaust speciations for operation over the Federal Test Procedure cycle and also for off-cycle tests.

The Texas Project was a multi-year study of aftermarket conversions of a variety of light-duty vehicles to CNG or LPG. One aspect of this project was to examine the factors that influence the economics of fleet conversions to these alternative fuels. The present analysis did not include longer-term effects (such as possible increases in exhaust system life or increases in tire wear). Additionally, assumptions were required to estimate the costs of repairs to the alternative fuel system and engine. Other factors considered include conversion cost, fuel prices, annual alternative fuel tax (as applied for the state of Texas), annual miles accumulated, and the percent miles traveled while using the alternative fuel for dual fuel conversions.

The Texas Department of Transportation (TxDOT) began using an emulsified diesel fuel as an emissions control measure in July 2002. They initiated a study of the effectiveness of this fuel in comparison to conventional diesel fuel for TxDOT's Houston District operations and included the fleet operated by the Associated General Contractors (AGC) in the Houston area. Cost-effectiveness analyses, including the incremental cost per ton of NOx removed, were performed. NOx removal was the focus of this study because Houston is an ozone nonattainment area, and NOx is believed to be the limiting factor in ozone formation in the Houston area. The cost factors accounted for in the cost-effectiveness analyses included the incremental cost of the fuel (including an available rebate from the State of Texas), the cost of refueling more often, implementation costs, productivity costs, maintenance costs, and various costs associated with the tendency of the emulsion to separate.

A technique was developed for measuring the Laminar Burning Velocity (LBV) of multi-component fuel blends for use in high-performance spark-ignition engines. This technique involves the use of a centrally-ignited spherical combustion chamber, and a complementary analysis code. The technique was validated by examining several single-component fuels, and the computational procedure was extended to handle multi-component fuels without requiring detailed knowledge of their chemical composition. Experiments performed on an instrumented high-speed engine showed good agreement between the observed heat-release rates of the fuels and their predicted ranking based on the measured LBV parameters.

A technology path has been identified for development of a high efficiency, durable, gasoline engine, targeted at achieving performance and emissions levels necessary to meet heavy-duty, on-road standards of the foreseeable future. Initial experimental and numerical results for the proposed technology concept are presented. This work summarizes internal research efforts conducted at Southwest Research Institute. An alternative combustion system has been numerically and experimentally examined. The engine utilizes gasoline as the fuel, with a combination of enabling technologies to provide high efficiency operation at ultra-low emissions levels. The concept is based upon very highly-dilute combustion of gasoline at high compression ratio and boost levels. Results from the experimental program have demonstrated engine-out NOx emissions of 0.06 g/hp/hr, at single-cylinder brake thermal efficiencies (BTE) above thirty-four percent.

The University of Texas 2000 Ethanol Vehicle Challenge team remains focused on cold start, cold drivability, fuel economy, and emissions reduction for our 2000 Ethanol Vehicle Challenge entry. We used the stock PCM for all control functions except control of an innovative cold-start system our team designed. The primary modifications for improved emissions control involved ceramic coating of the exhaust manifolds, use of close-coupled ethanol-specific catalysts, use of a moddified version of the California Emissions Calibrated PCM, and our cold-start system that eliminates the need to overfuel the engine at the beginning of the FTP. Additionally, we eliminated EGR at high load to improve power density. Major modifications, such as increasing the compression ratio or pressure boosting, were eliminated from consideration due to cost, complexity, reliability, or emissions penalties.

An optical access engine was used to image the liquid film evaporation off the piston of a simulated direct injected gasoline engine. A directional injector probe was used to inject liquid fuel (gasoline, i-octane and n-pentane) directly onto the piston of an engine primarily fueled on propane. The engine was run at idle conditions (750 RPM and closed throttle) and at the Ford World Wide Mapping Point (1500 RPM and 262 kPa BMEP). Mie scattering images show the liquid exiting the injector probe as a stream and directly impacting the piston top. Schlieren imaging was used to show the fuel vaporizing off the piston top late in the expansion stroke and during the exhaust stroke. Previous emissions tests showed that the presence of liquid fuel on in-cylinder surfaces increases engine-out hydrocarbon emissions.

A nephelometer system was developed to characterize engine particulate emissions from DISI engines. Results were correlated with images showing the location and history of particulates in the cylinder of an optical engine. The nephelometer's operation is based upon the dependence of scattered laser light on particulate size from a flow sampled from the exhaust of an engine. The nephelometer simultaneously measured the scattered light from angles of 20° to 160° from the forward scattering direction in 4° increments. The angular scattering measurements were then compared with calculations using a Mie scattering code to infer information regarding particulate size. Measurements of particulate mass were made based upon a correlation developed between the scattered light intensity and particulate mass samples trapped in a 0.2-micron filter. Measurements were made in a direct injection single-cylinder spark ignition research engine having a transparent quartz cylinder.

A new combustion concept has been developed and tested for improving the low to moderate load efficiency and NOx emissions of natural gas engines. This concept involves operation of a dual-fuel natural gas engine on Homogeneous Charge Compression Ignition (HCCI) in the load regime of idle up to 35 % of the peak torque. A dual-fuel approach is used to control the combustion phasing of the engine during HCCI operation, and conventional spark-ignited natural gas combustion is used for the high-load regime. This concept has resulted in an engine with power output and high-load fuel efficiency that are unchanged from the base engine, but with a 10 - 15 % improvement to the low to moderate load fuel efficiency. In addition, the engine-out NOx emissions during HCCI operation are over 90% lower than on spark-ignited natural gas operation over the equivalent load range.

The impingement of liquid fuel onto the surfaces of the combustion chamber (wall-wetting) has been shown to be an important source of HC emissions from direct-injected SI engines, and can even result in pool fires and diffusion flames. Some degree of wall wetting, particularly on the piston top, is believed to occur in every current DIG engine design, but the behavior of the wall-bound fuel throughout the engine cycle is poorly understood. The goal of this study was to gain a better understanding of the fundamental interaction between liquid fuel droplets and the piston under engine-like conditions, by observing the vaporization of individual fuel drops as the surface temperature and ambient pressures were varied in a controlled environment. The vaporization of several single-component fuels, binary mixtures, and multi-component fuels was examined in the range of surface temperatures between 50 and 300 °C and ambient pressures between 50 and 1270 kPa (abs).

Improved submodels for use in a dynamic engine/vehicle model have been developed and the resulting code has been used to analyze the tip-in, tip-out behavior of a computer-controlled port fuel injected SI engine. This code consists of four submodels. The intake simulation submodel is similar to prior intake models, but some refinements have been made to the fuel flow model to more properly simulate a timed port injection system, and it is believed that these refinements may be of general interest. A general purpose engine simulation code has been used as a subroutine for the cycle simulation submodel. A conventional vehicle simulation submodel is also included in the model formulation. Perhaps most importantly, a submodel has been developed that explicitly simulates the response of the on-board computer (ECM) control system.

A quasi-dimensional model for a direct injection diesel engine was developed based on experiments at Sandia National Laboratory. The Sandia researchers obtained images describing diesel spray evolution, spray mixing, premixed combustion, mixing controlled combustion, soot formation, and NOx formation. Dec [1] combined all of the available images to develop a conceptual diesel combustion model to describe diesel combustion from the start of injection up to the quasi-steady form of the jet. The end of injection behavior was left undescribed in this conceptual model because no clear image was available due to the chaotic behavior of diesel combustion. A conceptual end-of-injection diesel combustion behavior model was developed to capture diesel combustion throughout its life span. The compression, expansion, and gas exchange stages are modeled via zero-dimensional single zone calculations.

The mixture preparation process was investigated in a direct-injected, 4-valve, SI engine under motored conditions. The interaction between the high-pressure fuel jet and the intake air-flow was observed. Laser-sheet droplet imaging was used to visualize the in-cylinder droplet distributions, and a single-component LDV system was used to measure in-cylinder velocities. The fuel spray was visualized with the engine motored at 1500 and 750 rpm, and with the engine stopped. It was observed that the shape of the fuel spray was distorted by the in-cylinder air motion generated by the intake air flow, and that this effect became more pronounced with increasing engine speed. Velocity measurements were made at five locations on the symmetry plane of the cylinder, with the engine motored at 750 rpm. Comparison of these measurements with, and without, injection revealed that the in-cylinder charge motion was significantly altered by the injection event.

Predictions of the Fractal Engine Simulation code were compared with SI engine data in a previous paper. These comparisons were extremely good except for the single data set available at a low engine speed. Because of uncertainty regarding whether the lack of agreement for this case resulted from some difficulty with the experimental data or was due to lack of proper speed dependence in the model, additional comparisons are made for a range of speeds from 300-1500 rpm. The fractal burning model is a turbulence driven model (i.e., driven primarily by the turbulence intensity) that divides the combustion process into four sequential phases: 1) kernel formation, 2) early flame growth, 3) fully developed turbulent flame propagation, and 4) end of combustion. The kernel formation process was not included in the previous version of this model, but was found to be required to predict engine speed effects.

Multi-dimensional numerical simulation of the combustion process in spark ignition engines were performed using the Coherent Flame Model (CFM) which is based on the flamelet assumption. The CFM uses a balance equation for the flame surface area to simulate flame surface advection, diffusion, production and destruction in a turbulent reacting flow. There are two model constants in CFM, one associated with the modeling of flame surface production and the other with the modeling of flame surface destruction. Previous experimental results on two test engines charged with propane-air mixtures were used to compare with the computations for different engine speeds, loads, equivalence ratios and spark plug locations. Predicted engine cylinder pressure histories agree well with the experimental results for various operating conditions after the model constants were calibrated against a reference operating condition.