Search Results

Oxyfuel combustion and nitrogen-free combustion coupled with Carbon Capture and Storage (CCS) techniques have been recently proposed as an efficient method to achieve carbon free emissions and to improve the combustion efficiency in diesel engines. In this study, a 3-D computational fluid dynamics model has been used to evaluate the influence of oxyfuel-HCCI combustion on engine operating conditions and combustion characteristics in a HSDI diesel engine. Investigations have conducted using four different diluent strategies based on the volume fraction of pure oxygen and a diluent gas (carbon dioxide). The first series of investigations has performed at a constant fuel injection rating at which 4.4 mg of fuel has injected per cycle. In the second part of analysis, the engine speed was maintained at 1500 rev/min while the engine loads were varied by changing the fuel injection rates in the range of 2.8 to 5.2 mg/cycle.

Tumble and swirl motions in the cylinder of a four-valve SI engine with production type cylinder head were investigated using a cross-correlation digital Particle Image Velocimetry (PIV). Tumble motion was measured on the vertical symmetric plane of the combustion chamber. Swirl motion was measured on a plane parallel to the piston crown with one of intake ports blocked. Large-scale flow behaviours and their cyclic variations were analysed from the measured two-dimensional velocity data. Results show that swirl motion is generated at the end of the intake stroke and persists to the end of the compression stroke. Tumble vortex is produced in the early stage of the compression stroke and distorted in the late stage of the stroke. The cyclic variation of swirl motion is noticeable. The cyclic variation in tumble dominated flow field is much greater.

The effects of Air/Fuel (A/F) ratios and Exhaust Gas Re-Circulation (EGR) rates on Homogeneous Charge Compression Ignition (HCCI) combustion of n-heptane have been experimentally investigated. The experiments were carried out in a single-cylinder, 4-stroke and variable compression-ratio engine equipped with a port fuel injector. Investigations concentrate on the HCCI combustion of n-heptane at different A/F ratios, EGR rates and their effects on knock limit, engine load, combustion variability, and engine-out emissions such as NOx, CO, and unburned HC. Variations of auto-ignition timings and combustion durations in the two-stage combustion process are analyzed in detail. Results show that HCCI combustion with a diesel type fuel can be implemented at room temperature with a conventional diesel engine compression-ratio. However, its knock limit occurs at very high A/F ratios, although high EGR rates can be tolerated.

Owing to the potentials for low NOx and soot emissions, diesel PCCI combustion has been widely studied over last 10 years. However, its control is still the main barrier to constrain it to be applied on production engines. As there are a number of variables which affect the mixing and combustion process, it is difficult to develop control strategies with adequate functions but simple control order for implementing them. In the current research, a reformed Homogeneity Factor (HF) of in-cylinder charge has been explored as a control medium for simplifying the control model structure. Based on multi-pulse injection, the effects of operating parameters on the Homogeneity Factor and the relationship between Homogeneity Factor and mixing, combustion processes, emissions were investigated in a four-valve, direct-injection diesel engine by CFD simulation using KIVA-3V code coupled with detailed chemistry.

Effects of included spray angle with different injection strategies on combustion characteristics, performance and amount of pollutant emission have been computationally investigated in a common rail heavy-duty DI diesel engine. The CFD model was firstly validated with experimental data achieved from a Caterpillar 3401 diesel engine for a conventional part load condition at 1600 rev/min. Three different included spray angles (α = 145°, 105°, 90°) were studied in comparison with the traditional spray injection angle (α = 125°). The results show that spray targeting is very effective for controlling the in-cylinder mixture distributions especially when it accompanied with various injection strategies. It was found that 105° spray cone angle along with an optimized split pre- and post-Top Dead Center (TDC) injection strategy could significantly reduce NOx and soot emissions without much penalty of the fuel consumption, as compared to the wide spray angle.

The mechanism of NOx and soot reduction using different pilot and multiple injection strategies has been computationally studied in a heavy duty DI Diesel engine. A designed set of advanced injection schemes with various variables and exhaust gas recirculation rate (up to 10%) have been analyzed. The CFD model was firstly calibrated against experimental data for a part load operation at 1600 rpm. The computational models used were found to predict the correct trends obtained in the experiment. The study demonstrated the potential and explained the mechanism of the combination of EGR and multiple injection to reduce both soot and NOx emissions together with improved fuel economy.

An investigation has been carried out to examine the influence of re-entrant combustion chamber geometry on mixture preparation, combustion process and engine performance in a high-speed direct injection (HSDI) four valves 2.0L Ford diesel engine by CFD modeling. The computed cylinder pressure, heat release rate and soot and NOx emissions were firstly compared with experimental data and good agreement between the predicted and experimental values was ensured the accuracy of the numerical predictions collected with the present work. Three ITs (Injection Timing) at 2.65° BTDC, 0.65° BTDC and 1.35° ATDC, all with 30 crank angle pilot separations were also considered to identify the optimum IT for achieving the minimum amount of pollutant emissions.

An improved parameter called “Homogeneity Factor (HF) of in-cylinder charge” has been introduced as a measure to quantify the quality of the air-fuel mixing process in diesel engines. For this purpose, a CFD simulation has been performed to evaluate the effects of Homogeneity Factor on different injection strategies and its correlation with pre mixing process in a common rail DI diesel engine. The results showed a higher Homogeneity Factor will result in higher rate of air-fuel mixing and more complete combustion process. However, the careful adjustment must be made for ideal reduction for both NOx and soot emissions. It was also found when the dwell delay between injection pulses becomes longer, it leaves more time for the air-fuel mixing and initial combustion process of first injection pulse and therefore, the increase of Homogeneity Factor takes place at a later stage and it can caused a reduction of NOx formation.