Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Wall Temperature Effect on SI-CAI Hybrid Combustion Progress in a Gasoline Engine

2013-04-08
2013-01-1662
SI-CAI hybrid combustion, also known as spark-assisted compression ignition (SACI), is a promising concept to extend the operating range of CAI (Controlled Auto-Ignition) and achieve the smooth transition between spark ignition (SI) and CAI in the gasoline engine. In order to investigate the effect of the thermal boundary condition on the hybrid combustion, the experiments with different coolant temperatures are performed to adjust the chamber wall temperature in a gasoline engine. The experimental results indicate that increasing wall temperature would advance the combustion phasing, enlarge the peak heat release rate and shorten the combustion duration. While the capacity of the wall temperature effect on the hybrid combustion characteristics are more notable in the auto-ignition dominated hybrid combustion.
Technical Paper

Variable Geometry Turbocharger Active Control Strategies for Enhanced Energy Recovery

2013-03-25
2013-01-0120
This paper describes the development of the control system for a new type of mechanical turbocharger, the Active Control Turbocharger (ACT). The main difference of ACT compared to its predecessor, the Variable Geometry Turbocharger (VGT), lies in the inlet area modulation capability which follows an oscillating (sinusoidal) profile in order to match as much as possible the similar profile of the emitted exhaust gases entering the turbine in order to capturing the highly dynamic, energy content existent in exhaust pulses. This paper describes the development of a new controller in an adaptive framework in order to improve the response of the ACT. The system has been modelled using a one-dimensional Ricardo WAVE engine simulation software and the control system which actuates the nozzle (rack) position is modelled in Matlab-Simulink and uses a map-based structure coupled with a PID controller with constant parameters.
Technical Paper

Updated Prediction of the Physical Properties Needed for Modeling the Spray Behavior of Biodiesel Fuel

2014-10-13
2014-01-2750
It has been recognized that density, viscosity, surface tension, and volatility of liquid fuel are of great importance on the atomization and vaporization characteristics of biodiesel spray. This paper presents a comprehensive physical property prediction of biodiesel fuel for spray modeling with most recently developed property prediction models. The temperature-dependent properties of a soy methyl ester (SME) biodiesel were well predicted by the updated prediction methods. Then, the physical properties of the SME biodiesel were added into the KIVA-3V fuel library. By using the well predicted fuel properties, the spray behaviors of SME were successfully simulated by the KIVA-3V code under late-cycle post-injection, conventional diesel injection, and early-injection engine-relevant conditions. The simulation results agree reasonably well with the available experimental liquid penetrations under conditions of various ambient densities and temperatures.
Technical Paper

The Optimization of Intake Port using Genetic Algorithm and Artificial Neural Network for Gasoline Engines

2015-04-14
2015-01-1353
The flow performance of intake port significantly affects engine output power, fuel economy, and exhaust emissions in gasoline engines. Thus, optimal intake port geometry is desired in gasoline engines. To optimize the flow performance of intake port, a new optimization method combining genetic algorithm (GA) and artificial neural network (ANN) was proposed. First, an automatic system for generating the geometry of the tangential intake port was constructed to create various port geometries through inputting the 18 pre-defined structural parameters. Then, the effects of four critical structural parameters were investigated through numerical simulation. On the basis of the computational results, an ANN was used to model the flow performance of the intake port, and a genetic algorithm was simultaneously employed to optimize the flow performance by optimizing the four important structural parameters. Finally, the optimization results were verified through numerical simulation.
Technical Paper

The Influence of Intake Port and Pent-Roof Structures on Reversed Tumble Generation of a Poppet-Valved Two-Stroke Gasoline Engine

2014-04-01
2014-01-1130
In order to minimize short-circuiting of the intake charge in the poppet-valved 2-stroke engine, measures are taken to generate reversed tumble in the cylinder. In this study, five different types of intake ports and three types of pent-roof geometries were designed and analysed of their ability to generate and maintain reversed tumble flows by means of CFD simulation for their intake processes on a steady flow rig. Their flow characteristics were then assessed and compared to that of the vertical top-entry ports. Results show that the side-entry port designs can achieve comparatively high tumble intensity. The addition of flow deflectors inside the side-entry ports does not have much effect on the reversed tumble ratio. The top-entry ports have the highest flow coefficient among all the intake ports examined as well as producing strong reversed tumble. It is also found that the pent-roof at a wider angle helps to strengthen the tumble intensity due to increased air flow rate.
Technical Paper

The Influence of Dilution Composition and Temperature Upon a Stratified Charge Spark Ignition Engine

2000-06-19
2000-01-1947
A thermodynamic model has been utilised in the analysis of a SI engine operating with a divided charge stratification system. Such a charge stratification system divides the cylinder charge into two distinct regions: a combustible charge around the spark plug and a dilution charge beyond this. The model has been utilised to reveal differing effects of both dilution charge composition (EGR or air) and temperature upon the performance and emissions of such a stratified charge engine.
Technical Paper

The Effects on Diesel Combustion and Emissions of Reducing Inlet Charge Mass Due to Thermal Throttling with Hot EGR

1998-02-23
980185
This paper is a complementary to previous investigations by the authors (1,2,3,4) on the different effects of EGR on combustion and emissions in DI diesel engine. In addition to the several effects that cold EGR has on combustion and emissions the application of hot EGR results in increasing the inlet charge temperature, thereby, for naturally aspirated engines, lowering the inlet charge mass due to thermal throttling. An associated consequence of thermal throttling is the reduction in the amount of oxygen in the inlet charge. Uncooled EGR, therefore, affects combustion and emissions in two ways: through the reduction in the inlet charge mass and through the increase in inlet charge temperature. The effect on combustion and emissions of increasing the inlet charge temperature (without reducing the inlet charge mass) has been dealt with in ref. (1).
Technical Paper

The Application of Controlled Auto-Ignition Gasoline Engines -The Challenges and Solutions

2019-04-02
2019-01-0949
Controlled Auto-Ignition (CAI) combustion, also known as Homogeneous Charge Compression Ignition (HCCI), has the potential to simultaneously reduce the fuel consumption and nitrogen oxides emissions of gasoline engines. However, narrow operating region in loads and speeds is one of the challenges for the commercial application of CAI combustion to gasoline engines. Therefore, the extension of loads and speeds is an important prerequisite for the commercial application of CAI combustion. The effect of intake charge boosting, charge stratification and spark-assisted ignition on the operating range in CAI mode was reviewed. Stratified flame ignited (SFI) hybrid combustion is one form to achieve CAI combustion under the conditions of highly diluted mixture caused by the flame in the stratified mixture with the help of spark plug.
Journal Article

Study on a Versatile Liquid Dosing Device for IC Engine After-Treatment System

2015-04-14
2015-01-1035
A versatile liquid dosing device along with its metering theory, which can be applied to both SCR dosing system and DPF regeneration system of IC engine after-treatment system, is presented in this paper. The device is composed of a solenoid driven plunger pump, a nozzle and a pressure tube, and is pump-end controlled by PWM signals. Both electrically resistive and conductive liquids including DEF for SCR system, fuel for DPF regeneration, and gasoline for spark ignition engine, can be dispensed quantitatively with this device. A metering theory determining the liquid discharged per injection is developed by studying the system using a physical-mathematical model. The study shows that the liquid discharge can be well correlated with a measurable variable T3, which is associated with the net output energy. Experimental investigations verified that the metering results were independent of the state changes.
Technical Paper

Study on Spatial Characteristics of the In-Cylinder Flow Field in an I.C. Engine Using PIV

1998-10-19
982632
In-cylinder flow characteristics in a four-stroke diesel engine were studied experimentally by instantaneous measurements of swirl and squish flow velocity distribution with particle image velocimetry (PIV). The triple-exposed PIV films were interrogated on a self-made system to get the velocity distribution. The measured velocities were analyzed by spatially high-pass and low-pass filtering techniques. Vorticity distributions were also calculated using the measured data. As results, vortex structure of the flow field was clearly visualized. Spatially averaged in-cylinder flow energy was found decaying at high rate but the less-scaled flow components at much lower rate. Clearly visualized squish and reverse squish movements around the top dead center (TDC) during the compression stroke were found strongly affecting the swirl flow field. making the in-bowl flow energy increased.
Technical Paper

Study of Flame Speed and Knocking Combustion of Gasoline, Ethanol and Hydrous Ethanol (10% Water) at Different Air/Fuel Ratios with Port-Fuel Injection

2018-04-03
2018-01-0655
In this paper, an experimental study was performed to investigate characteristics of flame propagation and knocking combustion of hydrous (10% water content) and anhydrous ethanol at different air/fuel ratios in comparison to RON95 gasoline. Experiments were conducted in a full bore overhead optical access single cylinder port-fuel injection spark-ignition engine. High speed images of total chemiluminescence and OH* emission was recorded together with the in-cylinder pressure, from which the heat release data were derived. The results show that under the stoichiometric condition anhydrous ethanol and wet ethanol with 10% water (E90W10) generated higher IMEP with at an ignition timing slightly retarded from MBT than the gasoline fuel for a fixed throttle position. Under rich and stoichiometric conditions, the knock limited spark timing occurred at 35 CA BTDC whereas both ethanol and E90W10 were free from knocking combustion at the same operating condition.
Technical Paper

Study of Biodiesel Combustion in a Constant Volume Chamber with Different Ambient Temperature and Oxygen Concentration

2011-08-30
2011-01-1931
Biodiesel is a widely used biofuel in diesel engines, which is of particular interest as a renewable fuel because it possesses the similar properties as the diesel fuel. The pure soybean biodiesel was tested in an optical constant volume combustion chamber using natural flame luminosity and forward illumination light extinction (FILE) methods to explore the combustion process and soot distribution at various ambient temperatures (800 K and 1000 K) and oxygen concentrations (21%, 16%, 10.5%). Results indicated that, with a lower ambient temperature, the autoignition delay became longer for all three oxygen concentrations and more ambient air was entrained by spray jet and more fuel was burnt by premixed combustion. With less ambient oxygen concentration, the heat release rate showed not only a longer ignition delay but also longer combustion duration.
Technical Paper

Spray and Combustion Characteristics of n-Butanol in a Constant Volume Combustion Chamber at Different Oxygen Concentrations

2011-04-12
2011-01-1190
A very competitive alcohol for use in diesel engines is butanol. Butanol is of particular interest as a renewable bio-fuel, as it is less hydrophilic and it possesses higher heating value, higher cetane number, lower vapor pressure, and higher miscibility than ethanol or methanol. These properties make butanol preferable to ethanol or methanol for blending with conventional diesel or gasoline fuel. In this paper, the spray and combustion characteristics of pure n-butanol fuel was experimentally investigated in a constant volume combustion chamber. The ambient temperatures were set to 1000 K, and three different oxygen concentrations were set to 21%, 16%, and 10.5%. The results indicate that the penetration length reduces with the increase of ambient oxygen concentration. The combustion pressure and heat release rate demonstrate the auto-ignition delay becomes longer with decreasing of oxygen concentrations.
Technical Paper

Simulation of the Effect of Intake Pressure and Split Injection on Lean Combustion Characteristics of a Poppet-Valve Two-Stroke Direct Injection Gasoline Engine at High Loads

2018-09-10
2018-01-1723
Poppet-valve two-stroke gasoline engines can increase the specific power of their four-stroke counterparts with the same displacement and hence decrease fuel consumption. However, knock may occur at high loads. Therefore, the combustion with stratified lean mixture was proposed to decrease knock tendency and improve combustion stability in a poppet-valve two-stroke direct injection gasoline engine. The effect of intake pressure and split injection on fuel distribution, combustion and knock intensity in lean mixture conditions at high loads was simulated with a three-dimensional computational fluid dynamic software. Simulation results show that with the increase of intake pressure, the average fuel-air equivalent ratio in the cylinder decreases when the second injection ratio was fixed at 70% at a given amount of fuel in a cycle.
Technical Paper

Shallow Water Modeling Method for Simulating Squish Movement in Diesel Engines

1996-05-01
961128
In this paper, the application of Shallow Water Modeling (SWM) method to simulate the compressible viscous plane flow for studying squish movement in combustion chambers of diesel engines is reported. The principle and analogue criteria of this method are discussed and derived. Using this method combined with visualization technique, the flow patterns were obtained and compared with those obtained by other methods. T1te results show that the SWM method is adequate and favorable for such investigation.
Technical Paper

Research on Relativity of Knock Sensor Signal and Gasoline HCCI Combustion Obtained with Trapping Residual Gas

2010-04-12
2010-01-1242
A great deal of effort has been directed towards Gasoline HCCI engines, which have the potential of providing better fuel economy and emission characteristics than conventional SI engines. For stable HCCI engine operation, cycle-by-cycle based closed-loop control is needed. Such a control scheme requires an accurate and reliable sensor to monitor the combustion and provide a feedback signal. At present, the general method used to measure the combustion parameters is to monitor in-cylinder pressure with a cylinder pressure sensor. However, using in-cylinder pressure transducers is not feasible for use in mass production of HCCI engines. A good substitute to get information about combustion is the knock sensor, which is already equipped on engines on a large scale. In this paper, the knock signal from an HCCI engine equipped with 4VVAS is analyzed in detail to find the relationship between the combustion parameters and the knock sensor signal.
Technical Paper

Reduction of Methane Slip Using Premixed Micro Pilot Combustion in a Heavy-Duty Natural Gas-Diesel Engine

2015-09-01
2015-01-1798
An experimental study has been carried out with the end goal of minimizing engine-out methane emissions with Premixed Micro Pilot Combustion (PMPC) in a natural gas-diesel Dual-Fuel™ engine. The test engine used is a heavy-duty single cylinder engine with high pressure common rail diesel injection as well as port fuel injection of natural gas. Multiple variables were examined, including injection timings, exhaust gas recirculation (EGR) percentages, and rail pressure for diesel, conventional Dual-Fuel, and PMPC Dual-Fuel combustion modes. The responses investigated were pressure rise rate, engine-out emissions, heat release and indicated specific fuel consumption. PMPC reduces methane slip when compared to conventional Dual-Fuel and improves emissions and fuel efficiency at the expense of higher cylinder pressure.
Journal Article

Quantitative Study of Concentration and Temperature of a Diesel Spray by Using Planar Laser Induced Exciplex Fluorescence Technique

2010-04-12
2010-01-0878
The Lambert-Beer's coefficient K was measured in a wide range of temperatures (400-1200K) and pressures (2-8.2 MPa) in this paper. Based on the measured MAP of K and principle of energy conservation in the sprays mass and transfer, a quantitative presentation of equivalence ratio and temperature in vapor phase sprays at diesel engine like conditions was put forward. The experimental range of temperatures was 800-1100K and 20-100 kg/m₃ for density. It was found that the maximum equivalence ratio of vapor phase spray remained fairly constant at about 3.0 and the maximum equivalence ratio appearance earlier as the ambient density increased, while the ambient temperature in the constant volume vessel was set at 800K. The maximum equivalence ratio of vapor phase spray increased from about 3.0 to about 3.7 as ambient temperature increased from 800 to 1100K.
Technical Paper

Progress in Diesel HCCI Combustion Within the European SPACE LIGHT Project

2004-06-08
2004-01-1904
The purpose of the European « SPACE LIGHT » (Whole SPACE combustion for LIGHT duty diesel vehicles) 3-year project launched in 2001 is to research and develop an innovative Homogeneous internal mixture Charged Compression Ignition (HCCI) for passenger cars diesel engine where the combustion process can take place simultaneously in the whole SPACE of the combustion chamber while providing almost no NOx and particulates emissions. This paper presents the whole project with the main R&D tasks necessary to comply with the industrial and technical objectives of the project. The research approach adopted is briefly described. It is then followed by a detailed description of the most recent progress achieved during the tasks recently undertaken. The methodology adopted starts from the research study of the in-cylinder combustion specifications necessary to achieve HCCI combustion from experimental single cylinder engines testing in premixed charged conditions.
Technical Paper

Potentials of External Exhaust Gas Recirculation and Water Injection for the Improvement in Fuel Economy of a Poppet Valve 2-Stroke Gasoline Engine Equipped with a Two-Stage Serial Charging System

2018-04-03
2018-01-0859
Engine downsizing is one of the most effective means to improve the fuel economy of spark ignition (SI) gasoline engines because of lower pumping and friction losses. However, the occurrence of knocking combustion or even low-speed pre-ignition at high loads is a severe problem. One solution to significantly increase the upper load range of a 4-stroke gasoline engine is to use 2-stroke cycle due to the double firing frequency at the same engine speed. It was found that a 0.7 L two-cylinder 2-stroke poppet valve gasoline engine equipped with a two-stage serial boosting system, comprising a supercharger and a downstream turbocharger, could replace a 1.6 L naturally aspirated 4-stroke gasoline engine in our previous research, but its fuel economy was close to that of the 4-stroke engine at upper loads due to knocking combustion.
X