Search Results

The feasibility of using experimentally determined flow fields at intake valve closing, IVC, as initial conditions for computing the in-cylinder flow dynamics during the compression stroke is demonstrated by means of a computer simulation of the overall approach. A commercial CFD code, STAR-CD, was used for this purpose. The study involved two steps. First, in order to establish a basis for comparison, the in-cylinder flow field throughout the intake and compression strokes, from intake valve opening, IVO, to top dead center, TDC, was computed for a simple engine geometry. Second, experimental initial conditions were simulated by randomly selecting and perturbing a set of velocity vectors from the computed flow field at IVC.

Gas carburized and quenched low alloy steels typically produce surface microstructures which contain martensite, retained austenite and often NMTP's (non-martensitic transformation products). The NMTP's are caused by a reduction of surface hardenability in the carburizing process from loss of alloying elements to oxidation. Gas carburized low alloy steels such as SAE 8620 with NMTP's on the surface have been shown to have inferior bending fatigue properties when compared to more highly alloyed steels which do not form NMTP's, such as SAE 4615M. One method of minimizing the formation of oxides and eliminating NMTP formation during carburizing and quenching is to use plasma carburizing instead of conventional gas carburizing. In this study the microstructures and bending fatigue performance of plasma carburized SAE 8620 and SAE 4615M is compared to the same alloys conventionally gas carburized and quenched.

This paper describes the performance attributes of the all-new front and rear SLA (short-long arm) suspensions, steering system, and tires of the 1997 Corvette. The process by which these subsystem attributes flowed down from vehicle-level requirements for ride and handling performance is briefly described. Additionally, where applicable, specific subsystem attributes are rationalized back to a corresponding vehicle-level performance requirement. Suspension kinematic and compliance characteristics are described and contrasted to those of the previous generation (1984 to 1996 Model Year) Corvette. Both synthesis/analysis activities as well as mule-level vehicle development work are cited for their roles in mapping out specific subsystem attributes and related vehicle performance.

There is a clearly demonstrated need to develop “real-time” methods for the measurement of diesel vehicle particulate emissions. Optical techniques provide One alternative for such methodology because of the rapid data acquisition times involved and the relatively simple sampling methods that can be used. This report describes two different approaches to this problem. The first, the spectrophone, measures light absorption by the diluted exhaust plume using photoacoustic spectroscopy, and the second, the long pathlength smokemeter, determines total light extinction across the diluted exhaust plume. For the measurement of total mass emissions, both techniques show estimated errors of ±15% for specific vehicles, while for a multi-vehicle diesel fleet the estimated errors are ±20% and ±30% for the long pathlength smokemeter and the spectrophone, respectively.

Rapid Prototyping, Fabrication and Tooling is a process that blends a series of technologies (machines, tools, and methods) capable of generating physical objects directly from a CAD database. The process dramatically reduces the time spent during product development by allowing for fast visualization, verification, iteration, optimization, and fabrication of parts and tools. Many new techniques of tooling have been and are being developed by using rapid fabricated parts. These are having a dramatic impact on both timing and costs throughout the automotive industry. One area that these methods can be utilized to their full potential is motorsports. Of particular interest is the growing use of bridge tooling to provide first article through production intent parts that promote cost effective changes.

The use of Shadowgraph and Schlieren optical systems is a simple method to determine flow patterns of heated air external to the vehicle at idle. In particular, the method can be used to visualize natural convective air flow patterns at the underbody to aid in heat shielding design. Moreover, air recirculation patterns around the front end of the vehicle can be visualized without the use of smoke. The optical equipment is described and recommendations proposed for setting up the equipment. A video tape of some results is also presented.

This paper benchmarks some methods of nondestructive testing for zero and high mileage spot weld quality/integrity and degradation evaluation (pin holes, voids, cracks, fatigue, corrosion, etc.). The methods include X-ray radiography, ultrasonic imaging, ultrasonic pulse/ echo, pulsed infrared or thermography, and laser/TV holographic interferometry imaging. The advantages and limitations of each method are provided with descriptive principles and real test examples. It is found that X-ray radiography combined with ultrasonic echo technique is the most favorable one considering time and cost for the current zero and high mileage spot weld evaluation.

This book draws upon a variety of the author's experiences during more than 25 years in automotive safety. It gives an introduction to plain film radiographs (x-rays), computed tomograms (CTs), and magnetic resonance images (MRIs) such that vehicle safety professionals can use these techniques to help piece together the puzzle and provide a better understanding of the relationship between vehicle crash scenarios and occupant injury. For those with a primarily vehicle background, Neck Injury provides an overview of how x-rays, CTs, and MRIs may be used as a source of information to help analyze vehicle crashes and the associated injuries. For those with a clinical background, the book provides insight into how injuries relate to the vehicle crash. Chapters cover: Anatomy Imaging Injuries and Injury Mechanisms

In modeling of engine fuel-air mixing, it is desired to be able to predict fuel spray atomization under different injection and ambient conditions. In this work, a previously developed sheet atomization model was studied for this purpose. For sprays from a pressure-swirl injector, it is assumed in the model that the fuel flows out the injector forming a conical liquid film (sheet), and the sprays are formed due to the disintegration of the sheet. Modified formulations are proposed to estimate sheet parameters including sheet thickness and velocity at the nozzle exit. It was found that the fuel flow rate of a swirl injector satisfied the correlation well. Computations of correlation well. Computations of the sprays injected in an engine with a side-mounted injector were performed for conditions that duplicated a set of experiments performed in an optical engine. The computed results were compared with the spray images obtained from the optical engine using elastic (Mie) scattering.

Work has been performed to study side glass vibrations of a typical automobile using a scanning laser vibrometer. The objective of this work was to achieve better understanding of the source and path mechanisms for aeroacoustically generated wind noise. As a tool for measuring aeroacoustically generated vibrations, the laser vibrometer presents many advantages over traditional methods. These advantages, discussed in this paper, include rapid setup, full field imaging, high spacial resolution, non-contact operation, and wide dynamic and frequency ranges.

The complexity of designing and implementing a vehicle electrical control system for ultra fuel-efficient hybrid vehicles is significantly greater than that of a conventional vehicle. To quickly demonstrate and iterate capabilities of these vehicles, an efficient and rapid means for developing requirements, mapping these into an electrical control and communications architecture, and developing prototype systems is needed. The General Motors Precept concept vehicle is an example of an energy- efficient vehicular control system developed using a "requirements to software'' development process and electronic controller infrastructure that demonstrates these attributes. The Precept is General Motors Corporation's technology demonstration concept vehicle developed to address General Motors Corporation's commitment to the Partnership for a New Generation (PNGV) program.

Sector mesh modeling is the dominant computational approach for combustion system design optimization. The aim of this work is to quantify the errors descending from the sector mesh approach through three geometric modeling approaches to an optical diesel engine. A full engine geometry mesh is created, including valves and intake and exhaust ports and runners, and a full-cycle flow simulation is performed until fired TDC. Next, an axisymmetric sector cylinder mesh is initialized with homogeneous bulk in-cylinder initial conditions initialized from the full-cycle simulation. Finally, a 360-degree azimuthal mesh of the cylinder is initialized with flow and thermodynamics fields at IVC mapped from the full engine geometry using a conservative interpolation approach. A study of the in-cylinder flow features until TDC showed that the geometric features on the cylinder head (valve tilt and protrusion into the combustion chamber, valve recesses) have a large impact on flow complexity.

The Laser Ride Height Measurement and Calibration System measures and calibrates the ride height of a vehicle equipped with electronic suspension. The existing process of setting ride height is labor intensive and imprecise leading to vehicles that lean, have improper attitude, and suffer from alignment drift and pull. The proposed Machine and Process will impart the correct appearance and ride height to every vehicle which undergoes this test. A similar process can be used to measure the ride height of vehicles equipped with passive springs.

A rear obstacle detector and warning unit was designed to detect the presence of an object in the rear blind spot behind a vehicle and warn the operator if the possibility of backing over the object exists. A semiconductor infrared laser and a semiconductor detector, mounted on a vehicle behind the rear axle with a unique optical lens system proved capable of detecting small objects up to 10 ft directly behind the vehicle. The unit performance verified the ability to design an obstacle detection system with a sharply defined field of view using infrared technology.

An enlarged transparent model of a six-hole vertical diesel injector has been used to allow visualization of the flow at Reynolds and cavitation numbers matching those of real size injectors operating under normal Diesel engine conditions. The visualization system comprised a CCD camera, high-magnification lenses and a spark light source which allowed high-resolution images to be obtained. The flow conditions examined in terms of flow rates and pressures covered the range from low to full load of the real size injector while the needle lift position corresponded to that of full lift of the first- and second- stage in two-stage injectors. In addition, different values of needle eccentricity were tested in order to examine its effect on the cavitation structures within the injection holes.

A design of experiments is used to study the effect of laser weld parameters on formability of welded blanks for two different material combinations of cold rolled (bare) steel to cold rolled steel and cold rolled steel to hot dipped galvanized steel. Critical weld parameters influencing the formability of welded blanks are identified and the optimum weld set-up condition is obtained based on formability performance and consistency of formability for laser welded blanks. The results are applied to an automotive body side frame. The robustness of welded blank production is also assessed and the final welded set-up condition for the body side frame is obtained based on both the formability of welded blanks and the robustness of welded blank production. The body side frame is successfully made from the welded blanks with this final weld set-up condition.

A test facility was constructed at University College London to study fuel spray structure within a gasoline direct injection engine. The facility consisted of a single cylinder research engine with extensive optical access and a novel video imaging and analysis system. The engine used an experimental prototype 4-valve cylinder head with direct in-cylinder high pressure fuel injection, provided by a major automotive manufacturer. The fuel spray was illuminated using a pulsed copper-vapour laser. Results are presented that illustrate the spray behaviour within the fired research engine. A laser light sheet provided an insight into the inner spray cone behaviour.

It is known that the formability of tailored welded blanks depends on the welding set-up conditions. Little information is available on the correlation between the formability of welded blanks and weld set-up conditions. In this investigation, effects of mash seam welding parameters of weld current, weld force, material overlap and planish on formability performance of welded blanks are studied. The systematic design of experiments approach is used to identify the key weld parameters influencing the formability performance of welded blanks. It is found that high weld force decreases formability of welded blanks and high weld force coupled with a small material overlap results in very low forming limit of the weld zone. Weld current has little effect on formability of welded blanks and planishing significantly reduces it. Overall, the mash seam welded blanks produced with appropriate weld set-up conditions are robust with respect to formability.

Optimal design of modern direct injection spark-ignition engines depends heavily on the characteristics and distribution of the fuel spray. This study was designed to compliment imaging experiments of changes in the spray structure due to fuel volatility and operating conditions. Use of phase-Doppler particle analysis (PDPA) allows quantitative point measurements of droplet diameter and velocity. In agreement with imaging experiments, the results show that the spray structure changes not only with ambient gas density, which is often measured, but also with fuel temperature and volatility. The mean droplet diameter was found to decrease substantially with increasing fuel temperature and decreasing ambient density. Under conditions of low potential for vaporization, the observed trends in mean droplet sizes agree with published correlations for pressure-swirl atomizers.

Optimal design of modern direct injection spark-ignition engines depends heavily on the characteristics and distribution of the fuel spray. This study was designed to investigate changes in the spray properties due to fuel volatility and operating conditions using a firing optically-accessible engine with planar laser-induced fluorescence (PLIF) imaging. The results show that the spray structure changes not only with ambient gas density, which is often measured, but also with fuel temperature and volatility. As ambient pressure decreases and fuel temperature increases, the volatile ends of multi-component fuels evaporate quickly, disrupting the spray structure and producing a vapor core along the axis of the spray. Beyond a certain point, evaporation is rapid enough to expand the initial cone angle of the spray while causing a decrease in the overall spray width.