Search Results

Zero-dimensional heat release rate models have the advantage of being both easy to handle and computationally efficient. In addition, they are capable of predicting the effects of important engine parameters on the combustion process. In this study, a zero-dimensional combustion model based on physical and chemical sub-models for local processes like injection, spray formation, ignition and combustion is presented. In terms of injection simulation, the presented model accounts for a phenomenological nozzle flow model considering the nozzle passage inlet configuration and an approach for modeling the characteristics of the Diesel spray and consequently the mixing process. A formulation for modeling the effects of intake swirl flow pattern, squish flow and injection characteristics on the in-cylinder turbulent kinetic energy is presented and compared with the CFD simulation results.

As the late combustion phase in SI engines is of high importance for a further reduction of fuel consumption and especially emissions, the impacts of unburnt mass, located in a small volume with a relatively large surface near the wall and in the top land volume, is of high relevance throughout the range of operation. To investigate and quantify the respective interactions, a state of the art Mercedes-Benz single cylinder research SI-engine was equipped with extensive measurement technology. To detect the axial and radial temperature distribution, several surface thermocouples were applied in two layers around the top land volume. As an additional reference, multiple surface thermocouples in the cylinder head complement the highly dynamic temperature measurements in the boundary zones of the combustion chamber.

The oil supply of combustion engines today is typically realized by oil pumps with constant displacement. To secure the operational safety in hot idling these pumps are oversized, what causes low efficiency in most of operating speeds. IAV developed a vane-type oil pump, which allows to infinitely regulate the delivery rate. Because of no oil release over a pressure limiting valve the pump achieves a higher efficiency in a wide range of operation. The design of the theoretical delivery characteristic allows the calculated and particular increase of oil pressure to avoid critical operating conditions and to support hydraulically operated functions as variable camshaft timing.

State-of-the-art powertrain concepts with automatic transmission must comply with increasingly stringent legislation on emissions and fuel consumption while fulfilling or surpassing customers' expectations as to driveability. In this respect, automated manual transmissions (AMT) and automated shift transmissions (AST) must compete with conventional automatic transmissions (AT) and continuously variable transmissions (CVT). In order to exploit the theoretical advantages of ASTs and put them into practice, complex ECU functions are needed to coordinate engine and transmission. Adaptive control, sophisticated clutch management and an intelligent shifting strategy allow shifting quality and shifting points to be simultaneously optimized to the effect that performance and comfort are increased while fuel consumption is reduced.

Enhanced octane is one route to fuels differentiation where associated vehicle performance benefits are generally measured under controlled wide-open throttle tests on a chassis dynamometer. The combined availabilities of relevant ECU data via OBD and telematic loggers present new opportunities to assess such fuel benefits on the road in normal real-world driving environments. A novel methodology is described in this paper which utilised the remote logging of key engine EOBD data from a fleet trial and the results successfully demonstrated significant octane-derived benefits in many vehicles throughout normal mixed-roads driving. The availability and the reliability of telematic loggers mean that the method could be implemented in a scalable way as a complementary approach in addition to conventional laboratory vehicle testing.

Previous work has shown that it may be advantageous to use gasoline type fuels with long ignition delays compared to today's diesel fuels in compression ignition engines. In the present work we investigate if high volatility is also needed along with low cetane (high octane) to get more premixed combustion leading to low NO and smoke. A single-cylinder light-duty compression ignition engine is run on four fuels in the diesel boiling range and three fuels in the gasoline boiling range. The lowest cetane diesel boiling range fuel (DCN = 22) also has very high aromatic content (75%vol) but the engine can be run on this to give very low NO (≺ 0.4 g/kWh) and smoke (FSN ≺ 0.1), e.g,. at 4 bar and 10 bar IMEP at 2000 RPM like the gasoline fuels but unlike the diesel fuels with DCNs of 40 and 56. If the combustion phasing and delay are matched for any two fuels at a given operating condition, their emissions behavior is also matched regardless of the differences in volatility and composition.

This research describes the potential to adopt detailed chemical kinetics for practical and potential future fuels using tri-component surrogate mixtures capable of simulating fuel octane “sensitivity” . Since the combustion characteristics of modern fuels are routinely measured using the RON and MON of the fuel, a methodology to generate detailed chemical kinetic mechanisms for these fuels based on these data is presented. Firstly, a novel correlation between various tri-component blends (comprised of i-octane, n-heptane and toluene) and fuel RON and MON was obtained by carrying out standard octane tests. Secondly, a chemical kinetic mechanism for tri-component fuels was validated using a Stochastic Reactor Model (SRM) suite, an in-cylinder engine combustion simulator, and a series of engine experiments conducted in HCCI operating mode.

Under the persistent pressure to further reduce fuel consumption worldwide, it is necessary to advance the processes that influence the efficiency of gasoline engines. In doing so, harnessing the entire potential of fully variable mechanical valve trains will involve targeting efforts on optimizing all design parameters. A new type of valve timing system is used to portray thermodynamic and mechanical as well as electronic aspects of developing fully variable mechanical valve timing and lift systems

If fuels that are more resistant to auto-ignition are injected near TDC in compression ignition engines, they ignite much later than diesel fuel and combustion occurs when the fuel and air have had more chance to mix. This helps to reduce NOX and smoke emissions at much lower injection pressures compared to a diesel fuel. However, PPCI (Partially Premixed Compression Ignition) operation also leads to higher CO and HC at low loads and higher heat release rates at high loads. These problems can be significantly alleviated by managing the mixing through injector design (e.g. nozzle size and centreline spray angle) and changing CR (Compression Ratio). This work describes results of running a single-cylinder diesel engine on fuel blends by using three different nozzle design (nozzle size: 0.13 mm and 0.17 mm, centreline spray angle: 153° and 120°) and two different CRs (15.9:1 and 18:1).

This paper investigates an optimal design of a diesel engine and after-treatment systems for a series hybrid electric forklift application. A holistic modeling approach is developed in GT-Suite® to establish a model-based hardware definition for a diesel engine and an after-treatment system to accurately predict engine performance and emissions. The used engine model is validated with the experimental data. The engine design parameters including compression ratio, boost level, air-fuel ratio (AFR), injection timing, and injection pressure are optimized at a single operating point for the series hybrid electric vehicle, together with the performance of the after-treatment components. The engine and after-treatment models are then coupled with a series hybrid electric powertrain to evaluate the performance of the forklift in the standard VDI 2198 drive cycle.

The spray-guided combustion process offers a high potential for fuel savings in gasoline engines in the part load range. In this connection, the injector and spark plug are arranged in close proximity to one another, as a result of which mixture formation is primarily shaped by the dynamics of the fuel spray. The mixture formation time is very short, so that at the time of ignition the velocity of flow is high and the fuel is still largely present in liquid form. The quality of mixture formation thus constitutes a key aspect of reliable ignition. In this article, the spray characteristics of an outward-opening piezo injector are examined using optical testing methods under pressure chamber conditions and the results obtained are correlated with ignition behaviour in-engine. The global spray formation is examined using high-speed visualisation methods, particularly with regard to cyclical fluctuations.

Reduction of the CO2 greenhouse gas emissions is one major challenge the automotive industry as a part of the transportation sector is facing. Hydrogen is regarded as one of the key energy solutions for CO2 reduction in the future transportation sector. First, a hydrogen-powered single-cylinder test rig for 2 liter heavy-duty engine will be introduced. Followed by a discussion of experimental results including variations of engine speed, torque, ignition strategy, air-fuel ratio, etc. In addition, the paper proposes a new phenomenological model for the prediction of hydrogen combustion. The model is based on the well-known two-zone Entrainment approach, supported by newly developed hydrogen-specific submodels for the calculation of the laminar flame speed and auto-ignition in the unburned mass zone. The developed physical-based combustion model is extensively validated based on the experimental single-cylinder results.

The Noise, Vibration and Harshness (NVH) behaviour of the powertrain, the driveline and the mounting is playing a very important role in the vehicle development process. The method described in this paper presents the coupling of Multi Body Simulation (MBS) with mathematical optimization tools exemplary for a powertrain mounting at a passenger car vehicle. It is shown, how this approach is integrated in the IAV - development process for validation and for optimization, i.e. finding the best solution for reaching the NVH targets. In early stage of development process, torsional vibration models are used to simulate e.g. the decoupling between engine and transmission. To simulate further physical effects, the models must be more and more detailed with a lot of additional parameter. One challenge for valid models is the parameter identification. The process to do this successfully with mathematical methods will be described.

The precision of direct fuel injection systems of combustion engines is crucial for the further reduction of emissions and fuel consumption. It is influenced by the dynamic behavior of the fuel system, in particular the injection valves and the common rail pressure. As model based control strategies for the fuel system could substantially improve the dynamic behavior, an accurate model of the common rail injection system for gasoline engines - consisting of the main components high-pressure pump, common rail and injection valves - that could be used for control design is highly desirable. Approaches for developing such a model are presented in this paper. For each key component, two models are derived, which differ in temporal resolution and number of degrees of freedom. Experimental data is used to validate and compare the models. The data was generated on a test bench specifically designed and built for this purpose.

The majority of powertrain types considered important contributors to achieving the CO2 targets in the transportation sector employ a battery as an energy storage device. The need for batteries is hence expected to grow drastically with increasing market share of CO2-optimized powertrain concepts. The resulting huge pressure on the development of future electrochemical energy storage systems necessitates the application of advanced methodologies enabling a fast and cost-efficient concept definition and optimization process. This paper presents a model-based methodology for the optimization of BEV thermal management concept layouts and operation strategies targeting minimized energy consumption. Starting at the vehicle level, the proposed methodology combines appropriate representations of all primary powertrain components with 1D cooling and refrigerant circuit models and focuses on their interaction with the battery chemistry.

This paper shows the main results of a research activity carried out in order to investigate the impact of different hybridization concepts on vehicle fuel economy during standard homologation cycles (NEDC, FTP75, US Highway, Artemis). Comparative analysis between a standard passenger vehicle and three different hybrid solutions based on the same vehicle platform is presented. The following parallel hybrid powertrain solutions were investigated: Hybrid Electric Vehicle (HEV) solution (three different levels of hybridization are investigated with respect to different Electric Motor Generator size and battery storage/power capacity), High Speed Flywheel (HSF) system described as a fully integrated mechanical (kinetic) hybrid solution based on the quite innovative approach, and hydraulic hybrid system (HHV). In order to perform a fare analysis between different hybrid systems, analysis is also carried out for equal system storage capacities.

The development and calibration of exhaust aftertreatment (EAT) systems for the most diverse applications of diesel powertrain concepts requires EAT models, capable of performing concept analysis as well as control and OBD system development and calibration. On the concept side, the choice of an application-specific EAT layout from a wide technology selection is driven by a number of requirements and constraints. These include statutory requirements regarding emissions of criteria pollutants and greenhouse gases (GHG), technical constraints such as engine-out emissions and packaging, as well as economic parameters such as fuel consumption, and EAT system and system development costs. Fast and efficient execution of the analysis and multi-criteria system optimization can be done by integrating the detailed EAT models into a total system simulation.

The startability of SI engines, especially of DISI engines, is the greatest challenge when using ethanol blended fuels. The development of a suitable injection strategy is therefore the main engineering target when developing an ethanol engine with direct injection. In order to limit the test efforts of such a program, a vaporization model has been created that provides the quantity of vaporized fuel depending on pressure and on start and end, respectively number and split relation of injections. This model takes account of the most relevant fuel properties such as density, surface tension and viscosity. It also considers the interaction of the spray with cylinder liner, cylinder head and piston. A comparison with test results shows the current status and the need for action of this simulation model.

In-cylinder charge motion plays a key role in optimizing the combustion process of modern reciprocating engines. The present paper describes a method for obtaining the volumetric, isothermal, in-cylinder velocity flow field using Doppler Global Velocimetry (DGV). The DGV system is designed for measuring time-averaged velocity data in three different light sheet directions using a single camera system with the aim of providing planar, spatially resolved, three-component velocity data of the cylindrical cross section. As DGV provides time-averaged data, the results can be directly compared with data obtained by 3-D CFD analysis. An automated program code generates characteristic numbers of the measured velocity fields with the aim of assessing and comparing the results of different engine concepts.

After the realization of very low exhaust gas emissions and corresponding OBD requirements to fulfill Euro VI and Tier 4 legislation, the focus in heavy-duty powertrain development is on the reduction of fuel consumption and thus CO₂ emissions again. Besides this, the total vehicle operation costs play another major role. A holistic view of the overall powertrain system including the combustion process, exhaust gas aftertreatment, energy recuperation and energy storage is necessary in order to obtain the best possible system for a given application. A management system coordinating the energy flow between the different subsystems while guaranteeing low exhaust emissions plays a major part in operating such complex architectures under optimal conditions.