Search Results

In order to clarify future automobile technologies and fuel qualities to improve air quality, second phase of Japan Clean Air Program (JCAPII) had been conducted from 2002 to 2007. Predicting improvement in air quality that might be attained by introducing new emission control technologies and determining fuel qualities required for the technologies is one of the main issues of this program. Unregulated material WG of JCAPII had studied unregulated emissions from gasoline and diesel engines. Eight gaseous hydrocarbons (HC), four Aldehydes and three polycyclic aromatic hydrocarbons (PAHs) were evaluated as unregulated emissions. Specifically, emissions of the following components were measured: 1,3-Butadiene, Benzene, Toluene, Xylene, Ethylbenzene, 1,3,5-Trimethyl-benzene, n-Hexane, Styrene as gaseous HCs, Formaldehyde, Acetaldehyde, Acrolein, Benzaldehyde as Aldehydes, and Benzo(a)pyrene, Benzo(b)fluoranthene, Benzo(k)fluoranthene as PAHs.

The running direction of a vehicle can be controlled by not only wheel steer but also torque steer. This paper introduces the tractive torque steer effect produced by a newly developed electropneumatic control system, the limited-slip differential for large-sized vehicles. This system enhances the vehicle's running stability and controllability by controlling the tractive force of the drive axle. The tractive force maintains a stable running course against disturbances such as road roughness and wind gusts, thereby enhancing the steering response and providing a better feeling of handling to the driver. The system also improves mobility. especially on low-μ roads. It is expected that a single axle equipped with this system will exhibit good performance comparable to that of tandem axle.

To reduce ultra fine particle number concentration from a heavy-duty diesel engine, the effects of diesel fuel property and after-treatment systems were studied. The reduction of ultra fine particle number concentration over steady state mode using an 8 liter turbocharged and after-cooled diesel engine was evaluated. PM size distribution was measured by a scanning mobility particle sizer (SMPS). The evaluation used a commercially available current diesel fuel (Sulfur Content: 0.0036 wt%), high sulfur diesel fuel (Sulfur Content: 0.046 wt%) and low sulfur diesel fuel (Sulfur Content: 0.007 wt%). The after-treatment systems were an oxidation catalyst, a wire-mesh type DPF (Diesel Particle Filter) and a wall-flow type catalyzed DPF. The results show that fine particle number concentration is reduced with a low sulfur fuel, an oxidation catalyst, a wire-mesh type DPF (Diesel Particulate Filter) and wall flow type catalyzed DPF, respectively.

To reduce emissions from diesel engines, the effects of oxidation catalysts on the emissions reductions were studied. The effectiveness of several oxidation catalysts on both the regulated and unregulated emissions was evaluated. The oxidation activity of the catalysts was varied by changing Pt loading. The regulated emissions include particulate (PM), hydrocarbon (HC), and carbon monoxide (CO), and the unregulated emissions include benzene, formaldehyde, acetaldehyde, and benzo[a]pyrene (B[a]P). An 8 litter, turbocharged and aftercooled diesel engine was operated under the Japan Diesel 13 (D13) mode cycle for the evaluations. As the first step, evaluations were conducted with a commercially available JIS #2 diesel fuel (0.046 wt% sulfur). All the regulated and unregulated emissions except PM were reduced as the Pt loading (i.e. oxidation activity) increased. However, PM emissions were increased by the generation of sulfate when the Pt loading exceeded 0.2 g/l.

DPR consists of a multiple fuel-injection system, an electronic engine control unit, and a DPR Cleaner. The DPR cleaner is one assembly unit consisting of a DOC, a catalyzed DPF, and an exhaust silencer. Thus, DPR is a system developed to achieve healthy operation of a DPF with active regeneration regardless of engine operating conditions. The IP Filter was developed to improve the DPR cleaner by reducing the size of the unit and shortening the regeneration time. Both the DOC and DPF are integrated into one unit structure. The IP Filter has open-ended cells on the front face unlike a conventional wall-flow DPF. Instead, the plugs are positioned at the interface between the DOC and DPF. On the rear face of the IP Filter, plugs are installed at the same positions as those of a conventional DPF. The DOC substrate of the IP Filter is made of highly porous, straight honeycomb, the same as that of DPF.

The Hino E13C was developed for heavy-duty truck application to meet Japan's 2003 NOx and 2005 particulate emissions standards simultaneously with significant fuel economy improvement. A combined EGR system consisting of an external EGR system with a highly efficient EGR cooler and an internal EGR system with an electronically controlled valve actuation device was newly developed to reduce NOx emissions for all operating conditions without requiring a larger engine coolant radiator. A Hino-developed DPR was installed to achieve extremely low particulate emissions at the tail pipe. Increased strength of engine structural components and a ductile cast iron piston enabled high BMEP operation at lower engine speeds and reductions of both engine size and weight. This paper describes key technologies developed for the E13C as well as the development results.

A newly developed viscous-rubber damper, which employed an innovative structure and a new heat resistant rubber, solved some tough problems. This paper dealt more closely with the features of the new viscous-rubber damper and the new calculation method for the viscous-rubber damper. This damper has been employed for Hino new K13C (K-II) higher boost turbocharged and air to air charge-cooled diesel engine, which has extreme severity on the torsional vibration.

In Biodiesel Fuel Research Working Group(WG) of Japan Auto-Oil Program(JATOP), some impacts of high biodiesel blends have been investigated from the viewpoints of fuel properties, stability, emissions, exhaust aftertreatment systems, cold driveability, mixing in engine oils, durability/reliability and so on. This report is designed to determine how high biodiesel blends affect oil quality through testing on 2005 regulations engines with DPFs. When blends of 10-20% rapeseed methyl ester (RME) with diesel fuel are employed with 10W-30 engine oil, the oil change interval is reduced to about a half due to a drop in oil pressure. The oil pressure drop occurs because of the reduced kinematic viscosity of engine oil, which resulting from dilution of poorly evaporated RME with engine oil and its accumulation, however, leading to increased wear of piston top rings and cylinder liners.

A 2-LEG NOx Storage-Reduction (NSR) catalyst system is one of potential after-treatment technology to meet stringent NOx and PM emissions standards as Post New Long Term (Japanese 2009 regulation) and US'10. Concerning NOx reduction using NSR catalyst, a secondary fuel injection is necessary to make fuel-rich exhaust condition during the NOx reduction, and causes its fuel penalty. Since fuel injected in the high-temperature (∼250 degrees Celsius) exhaust instantly reacts with oxygen in common diesel exhaust, the proportion of fuel consumption to reduce the NOx stored on NSR catalyst is relatively small. A 2-LEG NSR catalyst system has the decreasing exhaust flow mechanism during NOx reduction, and the potential to improve the NOx reduction and fuel penalty. Therefore, this paper studies the 2-LEG NSR catalyst system. The after-treatment system consists of NSR catalysts, a secondary fuel injection system, flow controlled valves and a Catalyzed Diesel Particulate Filter (CDPF).

A driving simulator system for developing steering road feel has been developed. A new steering gear box or an electronic steering system is installed on the simulator and its road feel and control algorithm are developed according to the characteristics of any vehicle which has been programed into the engineering work-station. The vehicle model programed into the engineering work station runs according to the driver's operations, which are fed through the new steering system to be tested. The steer-restoring torque of the vehicle programed into the engineering work-station is produced by an actuator, and gives the impression through the new system of having been fed back from an actual road.

In the Japanese heavy duty truck market, demands of improved fuel economy and lighter vehicles to increase load capacity, and further improvements in emissions are constantly increasing. To satisfy these requirements, basically a smaller sized and higher boosted diesel engine is effective, because such an engine has a compact size and light weight, and shows improved fuel consumption due to a relatively lower frictional loss. On the basis of this concept Hino introduced the original EP100 in 1981 as the first Japanese turbocharged and air to air charge-cooled engine. Since then Hino has made many efforts to improve the engines and develop new technologies.

In a tractor-trailer, ride comfort affected by horizontal human body motions, so called “wavy” and “shaky” feelings, is at issue. Insight about “wavy” and “shaky” feelings which is important for efficient vehicle development is not enough. Experiments using 6-axis motion generator and motion capture and inverse-analysis using multi-body human model indicated the characteristics of each feeling. Motion observation and transfer function indicated that while a bad subjective score of “wavy” feeling corresponds to same-phase roll motion of chest and pelvis up to 0.7Hz, “shaky” correlates to an antiphase of them around 2Hz. By multiple regression, dominant vibration components of the human body and the vehicle to subjective evaluation of the feelings above were identified. Explanatory variables for the “wavy” feeling are roll rate and lateral jerk and those for the “shaky” are lateral acceleration and longitudinal acceleration.

Ultra-low energy consumption and ultra-low emission vehicle technologies have been developed by combining petroleum-alternative clean energy with a hybrid electric vehicle (HEV) system. Their component technologies cover a wide range of vehicle types, such as passenger cars, delivery trucks, and city buses, adsorbed natural gas (ANG), compressed natural gas (CNG), and dimethyl ether (DME) as fuels, series (S-HEV) and series/parallel (SP-HEV) for hybrid types, and as energy storage systems (ESSs), flywheel batteries (FWBs), capacitors, and lithium-ion (Li-ion) batteries. Evaluation tests confirmed that the energy consumption of the developed vehicles is 1/2 of that of conventional diesel vehicles, and the exhaust emission levels are comparable to Japan's ultra-low emission vehicle (J-ULEV) level.

The toe-change of road-wheel, so-called compliance-steer(CS), caused by suspension compliance is proved to occur around a steady instantaneous center under steady run at constant speed. The adverse/proverse CS, that increases/decreases the side-slip angle versus the velocity vector of vehicle, is realized by locating the center rearward/forward of the axle. By designing the front/rear wheel CS as a proverse/adverse CS with nonlinear compliance that is large at on-center but small at off-center, vehicle characteristics to reduce lateral deviation caused by disturbance and to improve tracking performance are possible.

Understanding and prediction of flash-boiling spray behavior in gasoline direct-injection (GDI) engines remains a challenge. In this study, computational fluid dynamics (CFD) simulations using the homogeneous relaxation model (HRM) for not only internal nozzle flow but also external spray were evaluated using CONVERGE software and compared to experimental data. High-speed extinction imaging experiments were carried out in a real-size axial-hole transparent nozzle installed at the tip of machined GDI injector fueled with n-pentane under various ambient pressure conditions (Pa/Ps = 0.07 - 1.39). The width of the spray during injection was assessed by means of projected liquid volume, but the structure and timing for boil-off of liquid within the sac of the injector were also assessed after the end of injection, including cases with different designed sac volumes.

Hino Motors is about to launch a new truck model FA as a family product of the model FB class 5 category trucks which have been sold since 1986, Model FA, a class 3 category cab-over-engine truck has a GVW of 13,500 Lbs. and is powered by a 3.8 liter direct injection turbocharged diesel engine which produces 125 HP in conformity with federal exhaust gas emission regulations for 50 states. The new truck was designed and developed to satisfy several principal design objectives such as excellent maneuverability, driving comfort, superior fuel economy as well as sufficient reliability and durability within the simplest possible structure. This paper describes its design objectives, features focusing on cab and engine and technologies devoted to the development.

Reducing friction between the piston ring and cylinder is an effective way of meeting the demand for lower fuel consumption in vehicle engines. To that effect, the authors have proposed a new and efficient friction reduction treatment for the cylinder. At first glance, this treatment seems similar to typical microtexture treatments, but it is built on a different approach. Through a rig tester, it was confirmed that optimizing the shape of the dimples and the treatment area for the cylinder improves FMEP between the piston ring and the cylinder liner by 17%. This report presents an analysis of the test results to explain the mechanism by which this effect is achieved. Fuel consumption was measured in an actual engine, and a maximum fuel consumption improvement of 3.2% was confirmed after conversion to the Japanese heavy duty vehicle fuel economy standards (Category T2). Lubricating oil consumption, blow-by and durability were also examined.

It is preferable that power steering permits “static park” and has a good “road Feel” when running. In order to permit “static park”, a large bore actuation cylinder with high flow pump is required. Such a method, however, has two defects, a loss power for driving a large volume pump and a poor “road feel”. Resolving these problems and achieving the above matters. Hino has developed a load sensing power steering system. This system, which employes two actuation cylinders controlled by means of a unique load sensing valve arrangement, is designed to permit use of only one cylinder for highway speeds and both cylinders during a static park maneuver. When the system is combined with the preceding speed sensing power steering, “static park” is further facilitated and a tasty “road feel” is available in accordance with vehicle speed.

An integrated engine subsystem incorporating Internal Exhaust Gas Recirculation (IEGR) or alternatively referred to as Pulse EGR™ and Compression Release Retarding (CRR) functions has been developed and introduced to production with the new E13C engine from Hino Motors Ltd. This new system provides the nitrous oxide (NOX) reduction benefit of IEGR and the vehicle control and brake saving benefits of CRR in a single integrated package, without the need for increased vehicle cooling capacity or additional components external to the engine. The product is a result of a close cooperation between two companies, Hino Motors Ltd. of Japan and Jacobs Vehicle Systems, Inc. of the U.S.A.

To reduce the vehicle fuel consumption at high speed, it is very effective to minimize the aerodynamic resistance of the vehicle, which forms most of the vehicle running resistance at high speed. This paper presents a reduction of the aerodynamic resistance of van type truck through the wind tunnel tests using 1/5 scaled model. Firstly, the aerodynamically desirable cab shape for cargo type truck is investigated by changing main cab shape factors such as corner curvatures. Secondly, several effective attachments for Van type truck are investigated, and lastly, the effect of these aerodynamic improvements on the fuel consumption are clearified by vehicle running test.