Search Results

Diesel Engines are known for its low fuel consumption coupled with high specific power output. Downsizing the engines with turbocharging and common rail injection technologies are the recent trends in improving the efficiency and performance of diesel engines. It is very challenging to match the torque targets at low speed and power targets at high speed range of a diesel engines due to system hardware limitation. Torque at lower engine speed will improve a greater extent to the drivability of a vehicle. Formation of black smoke is a major problem in lower engine speeds due lack of air availability. The use of variable geometry, two stage turbocharging and four valves per cylinder are some of the solutions which make the task simpler, also involves additional cost and fundamental design changes. At the same time commonly used waste gate turbocharger for boosting the airflow, fails to deliver required air flow at lower engine speeds.

This paper is an attempt to compile a systematic approach which can be easily incorporated in the product development system used in the design and development of parking brake systems for passenger cars having rear drum brakes, which in turn can effectively reduce the lead time and give improved performance. The vehicle GVW, percentage gradient and maximum effort limits (as per IS 11852 - Part 3), tire and drum brake specifications were taken as front loading. This data is used for target setting of functional and engineering parameters, such as lever pull effort, lever ratio and angular travel of lever. Design calculations were performed to obtain theoretical values of critical parameters like lever effort and travel. The comparison between target and theoretical values give the initial confidence to the system engineer. Further, the outcome was taken to conceptualize the hard points of lever on vehicle for ergonomics.

The side door closing effort is one of the main evaluating parameters which demonstrates the build quality of the vehicle. The side door hinge axis inclination is one of the key attributes that affect the side door closing effort. Commonly, the hinge axis is inclined in two directions of a vehicle to have necessary door rise during the door opening event. Due to the process and assembly variations in the door assembly, the upper and lower hinge axis of the side door deviates from the design axis. In this paper, the deviations in the side door hinge axis and its effects on the side door closing velocity is discussed. The deviations of the side door hinge axis are studied with a coordinate measuring machine. The side door closing velocity of the vehicle is measured with the velocity meter. The study revealed that side door closing velocity is increasing with an increase in the deviation of the top and bottom door hinge axis from the design hinge axis.

Side Door closing velocity is one of the key customer touch points which depicts the build quality of the vehicle. Side door closing velocity results from the interaction of different parts like door and body seals, door check arm, door hinge, latch, and alignment of door hinge axis. In this paper, a high door closing velocity issue in a sports utility vehicle is discussed. Physical studies are carried out to understand each parameter in door closing velocity and its contribution is defined in terms of velocity. Many physical trials are conducted to conclude the contribution of each parameter. Studies revealed that the body and door seal are contributing around 70% of door closing velocity. Check arm and hinge axis deviation are contributing around 10% of the door closing velocity. Physical trials are conducted by reducing the compression distance of the body seal.

The contribution of engine borne noise is the major source of vehicle noise in diesel powered vehicles. The engine noise can be minimized by modification of engine components design and also with different acoustic abatement techniques. The research activities were carried out on 4-cylinder CRDe engine for SUV application. All the emission and performance parameters along with combustion noise was captured continuously for all the part load points from 1000 RPM to 2750 RPM with respect to the different road conditions and driving cycle. This paper targets on reducing the combustion noise at the noise prone zones only on the basis of the injection strategies ensuring no ill effect on the emissions and fuel economy. The first step was the reduction of rail pressure which helped noise levels to be reduced by almost 6 dB at noise zones. Main injection timing retardation was tried at all possible zones which influenced in considerable noise reduction at various zones.

Tractor weight transfer is the most common farm-related cause of fatalities nowadays. As in India it is getting mandatory for all safety devices across all HP ranges. Considering any changes in the weight from an attachment such as Rops, PTO device, tow hook and draw bar etc. can shift the center of gravity towards the weight. center of gravity is higher on a tractor because the tractor needs to be higher in order to complete operations over crops and rough terrain. Terrains, attachments, weights, and speeds can change the tractor’s resistance to turning over. This center of gravity placement disperses the weight so that 30 percent of the tractor’s weight is on the front axle and 70 percent is on the rear axle for two-wheel drive propelled tractors and it must remain within the tractor’s stability baseline for the tractor to remain in an upright position.

This study introduces a method to examine the flow path of the lubricant inside a transmission housing of a tractor. A typical gearbox has several loads bearing elements which are in relative sliding motion to each other which causes heat to be released. The major sources of friction as well as heat are the meshing teeth between gears (sun/planet, planet/ring & power/range drive gear), thrust washers, thrust bearings and needle roller bearings. The churning of oil performs the vital function of both lubricating these sliding interfaces and cooling these sources of heat, thereby preventing failure of the gearbox. In this paper, we have applied VOF multiphase flow model and sliding meshing to simulate the fluid flow during splashed lubrication within a mating gear box. Lubrication oil dynamics and oil surface interaction with the air is modeled using VOF multiphase approach.

Current high rating thermal loaded engines must have super-efficient lubrication system to provide clean oil at appropriate pressure and appropriate lube oil temperature to every part of the engine at all engine RPM speeds and loads. So oil pump not only have to satisfy above parameters but also it should be durable till engine life. Gerotor pumps are internal rotary positive-displacement pumps in which the outer rotor has one tooth more than the inner rotor. The gear profiles have a cycloidal shape. Both are meshed in conjugate to each other. Gerotor takes up engine power through crankshaft and deliver to various engine consumers at required pressure and required time. Over the complete engine rpm speed and loads range, oil pump need to perform efficiently to provide proper functioning of the engine. Otherwise low oil pressure leads to more friction in the pump, seizure of bearings and final failure of the engine .High oil pressure can lead to failure in oil filter, gaskets and seal.

The automotive industries around the world is undergoing massive transformation towards identifying technological capabilities to improve vehicle performance. In this regard, the engine dynamic torque plays a crucial role in defining the transient performance and drivability of a vehicle. Moreover, the dynamic torque is used as a visualization parameter in performance prediction of a vehicle to set the right engineering targets and to assess the engine potential. Hence, an accurate measurement and prediction of the engine dynamic torque is required. However, there are very few methodologies available to measure the engine dynamic torque with reasonable accuracy and minimum efforts. The measurement of engine brake torque using a torque transducer is one of the potential methods. However, it requires a lot of effort and time to instrument the vehicle. It is also possible to back-calculate the engine torque based on fuel injection quantity and other known engine parameters.

The tractor usage is growing in the world due to derivative of rural economy and farming process. It needed wide range of implements based on the applications of the customer. The tractor plays a major role in Agricultural and Construction applications. In a tractor, hydraulic system is act as a heart of the vehicle which controls the draft and position of the implement. Hydraulic system consists of Powertrain assembly, 3-point linkage and DC sensing assembly. The design of hydraulic powertrain assembly is challenging because the loads acting on the system varies based on the type of implement, type of crop, stage of farming and soil conditions etc., Hydraulic powertrain assembly is designed based on standards like IS 12207-2019 which regulates the test methods for the system based on the lift capacity of the tractor. In this paper, virtual simulation has been established to optimize the design and perform the test correlation.

In the event of a frontal car crash, occupant sitting in a car meets various types of injuries like Head injury, Chest compression, Neck injury etc. These injuries may lead to the death of an occupant if exceeded beyond biomechanical limits. Seat belt is a primary restraint system, which when worn controls the motion of occupant sitting inside the car during the event of a car crash. An Anchorage location of three point seat belt system has significant effect on occupant injuries during the crash event. By changing the mount locations of a seat belt anchor points i.e. D-ring, Anchor & Buckle, performance of seatbelt system can be enhanced further thereby reducing occupant injuries to certain extent. As per regulation AIS015, locations of safety belt anchorage points should be within prescribed zone.

Condition Monitoring is the process of identifying any significant change in operating parameters of a machine, which can be indicative of a failure in future. This paper discuss a non-invasive condition monitoring methodology for sensing and investigating the problems which could be identified by noise and vibrations. This could be an easy solution for predicting failures in tractors which are operational in the field. An example of engine tappet is used to demonstrate the methodology. A disturbed setting causes a distinguishable noise, referred to as “tappet rattle”. Android smartphones (with inbuilt sensors - accelerometer, gyroscope and microphone) are used to record noise and vibration from tractors in good condition as well as in disturbed condition. Time series data analysis is done to extract relevant features and then Fourier Transform is applied to the signals for extracting frequency domain signatures.

Steering returnability while driving is one of the most important parameter which affects the drive pleasure and handling of a vehicle. Steering returnability refers to the automatic returning response of the steering wheel after taking a full turn while vehicle is being steered during driving. Evaluating steering response characteristics of any vehicle in a virtual environment at early stage of a product development saves significant development time and cost. Through this paper an attempt has been made to develop a methodology for selection of suspension hard points which influences steering returnability characteristics of a vehicle at an early product design stage. Conventionally, suspension kinematic parameters such as Caster angle, Steering axis inclination (SAI), etc. are iterated during vehicle design stage to achieve desired Steering returnability.

Fuel economy, performance and drivability are the three important parameters for evaluating the vehicle performance. Powertrain matching plays a major role in meeting the above targets. Fuel economy is measured based on city, highway and some user defined driving cycles which can be considered as real world usage profiles. Performance and Drivability is evaluated based on the in-gear, thru-gear (acceleration performance) and grade-ability performance. The load collective points of the engine greatly influence the engines performance, fuel economy and emissions, which in-turn depends on the N/V ratio of the vehicle. The optimal selection of gear and final drive ratios plays a key role in the optimization of the Powertrain for a particular vehicle. The current study involves dynamic simulation of the vehicle performance and fuel economy at transient engine test-bed for different gear and final drive ratio combinations using AVL DynoExcat-dynamometer.

Computer Aided Engineering (CAE) simulations are an integral part of the product development process in an automotive industry. The conventional approach involving pre-processing, solving and post-processing is highly time-consuming. Emerging digital technologies such as Machine Learning (ML) can be implemented in early stage of product development cycle to predict key performances without need of traditional CAE. Oil Canning loadcase simulates the displacement and buckling behavior of vehicle outer styling panels. A ML model trained using historical oil canning simulation results can be used to predict the maximum displacement and classify buckling locations. This enables product development team in faster decision making and reduces overall turnaround time. Oil canning FE model features such as stiffness, distance from constraints, etc., are extracted for training database of the ML model. Initially, 32 model features were extracted from the FE model.

Ground clearance plays a vital role in an off-road vehicle during off roading. Higher the ground clearance, higher is the difficulty during ingress & egress of the vehicle. This brings in the necessity to provide entry-assist grab-handles for vehicle with more ground clearance (>200mm). Entry-assist grab handles alleviates the pain of the occupants during ingress and egress. For entry-assist grab handles’ purpose to be served, it should provide comfortable ergonomic grip & have to take the load of passengers while ingress or egress through-out the complete life cycle of the vehicle. Entry Assist grab handles can be fitted on A-Pillar zone to assist first row passengers & on B-pillar zone to assist second row passenger. Providing entry-assist grab handles on pillar trims make the grab-handles exposed to head-impact zone and hence, in most of the cases, it should pass the head impact regulations framed for respective countries.

Climate change is primary driver in the current discussions on CO2 reduction in the automotive industry. Current Type approval emissions tests (BS III, BS IV) covers only tailpipe emissions, however the emissions produced in upstream and downstream processes (e.g. raw material sourcing, manufacturing, transportation, vehicle usage, recycle phases) are not considered in the evaluation. The objective of this project is to assess the environmental impact of the product considering all stages of the life cycle, understand the real opportunities to reduce environmental impact across the product life cycle. As a part of environmental sustainability journey in business value chain, lifecycle assessment (LCA) technique helps to understand the environmental impact categories. To measure overall impact, a cradle to grave approach helps to assess entire life cycle impact throughout various stages.

Design and development of high-pressure pipe involves number of design validation plans for robust design in diesel engine. The fundamental behavior of two-cylinder diesel engine with parallel stroke involves high vibration which generates stress on components mounted on crankcase resulting into earlier fatigue failure. In this paper, the innovative approach of using optimized design of vibration damper for resolving high vibration stress concerns in fuel system is discussed. The vibration dampers were designed meeting both performance and durability aspects in two-cylinder diesel engine applicable for both passenger and commercial vehicle. This paper highlights the design approach involving experimental stress measurements and design optimization based on part development feasibility.

This paper presents a comprehensive model of a hydraulic power steering system for predicting the transient responses under various steering inputs. The hydraulic system model, which integrates together all fluid line elements and hydraulic components, is formulated using the MSC Easy5 software. A full vehicle model is developed in ADAMS/Car. Functional Mock up Interface (FMI), a tool independent standard is used for co-simulation of ADAMS and Easy5 Dynamic models. This paper describes a co-simulation methodology developed using FMI interface for full vehicle Simulations using hydraulic power steering. A virtual simulation scheme is developed to obtain the system transient responses and the results are compared with those measured from the tests. In general, the simulation results agree with those obtained from the tests under the same steering inputs and operating conditions.

Certain sports utility vehicles (SUVs) utilize dual latches and gas struts in their hood design. This is primarily driven by the larger size of the hood and specific architectural requirements. These hoods can be securely latched either by a dynamic single stroke closing method or by quasistatic two stroke closing method. In dynamic method, the hood is closed with a single, high-velocity motion for the final primary latching, whereas in quasistatic method, force is initially applied for the secondary latching and then for the final primary latching. In this study, both the dynamic and quasistatic closing methods are compared in terms of closing force and velocity and hood over travel distance. A load cell is used for measuring the closing force, velocity meter is used for velocity measurement and a rope sensor is used for measuring the hood over travel distance.