Search Results

To investigate the feasibility of various test procedures to determine aerodynamic performance for the Phase 2 Greenhouse Gas (GHG) Regulations for Heavy-Duty Vehicles in the United States, the US Environmental Protection Agency commissioned, through Southwest Research Institute, constant-speed torque tests of several heavy-duty tractors matched to a conventional 53-foot dry-van trailer. Torque was measured at the transmission output shaft and, for most tests, also on each of the drive wheels. Air speed was measured onboard the vehicle, and wind conditions were measured using a weather station placed along the road side. Tests were performed on a rural road in Texas. Measuring wind-averaged drag from on-road tests has historically been a challenge. By collecting data in various wind conditions at multiple speeds over multiple days, a regression-based method was developed to estimate wind-averaged drag with a low precision error for multiple tractor-trailer combinations.

The benchmarking study described in this paper uses data from chassis dynamometer testing to determine the efficiency and operation of vehicle driveline components. A robust test procedure was created that can be followed with no a priori knowledge of component performance, nor additional instrumentation installed in the vehicle. To develop the procedure, a 2013 Chevrolet Malibu was tested on a chassis dynamometer. Dynamometer data, emissions data, and data from the vehicle controller area network (CAN) bus were used to construct efficiency maps for the engine and transmission. These maps were compared to maps of the same components produced from standalone component benchmarking, resulting in a good match between results from in-vehicle and standalone testing. The benchmarking methodology was extended to a 2013 Mercedes E350 diesel vehicle. Dynamometer, emissions, and CAN data were used to construct efficiency maps and operation strategies for the engine and transmission.

Fourier Transform Infrared Spectroscopy (FT-IR) has been used to measure the exhaust emissions from vehicles during standard driving tests. Comparisons with conventional analyzers for modal tests have been made for the regulated species such as carbon monoxide (CO), nitrogen oxides (NOx) and total hydrocarbon (THC). The concentrations of methane, methanol and formaldehyde were also measured at one second time intervals during several driving tests. The average concentration values for these species were compared to the bag samples for several tests. Modal concentration curves were also calculated for MTBE, ETBE and several other species of interest. The results indicate FT-IR can be used for making modal measurements on the regulated species and non-regulated species in vehicle exhaust emissions. Several studies were performed to evaluate the long-term stability and sensitivity of FT-IR in actual test situations.

Exhaust emissions were evaluated for four different catalytic exhaust emission control systems. Each system utilized a diesel oxidation catalyst, a metal-substrate partial-flow diesel particulate filter, an iron-exchanged or copper-exchanged Y-zeolite catalyst for urea selective catalytic reduction, and an ammonia slip catalyst. A 5.9-liter diesel truck engine was modified to match the exhaust conditions of a four-stroke diesel locomotive engine meeting the current Tier 2 locomotive emissions standards. NOx emissions, CO₂ emissions and exhaust temperatures were matched to the eight locomotive "throttle notch" power settings while exhaust mass flow was maintained near a constant fraction of locomotive exhaust mass flow for each "throttle notch" position. Regulated and unregulated exhaust emissions were measured over a steady-state test cycle for each of the four systems at low hours and following accelerated thermal aging and accelerated oil ash accumulation.

This study is the second in a series of three EPA studies to investigate the effect of fuel reformulations and modifications on exhaust emissions. Both the first and second study in this series of studies were used to support the development of EPA's complex model for the certification of reformulated gasolines. Phase I of the study tested eight fuels on forty vehicles. This study, termed Phase II, tested twelve fuels on a separate fleet of 39 light-duty vehicles. The Phase II fuel parameters studied included Reid Vapor Pressure (RVP), the 50% and 90% evaporated distillation temperatures (T50 and T90), sulfur content, aromatics content, olefin content, oxygenate type and oxygen content. Measured exhaust emissions included total hydrocarbons (THC), oxides of nitrogen (NOx), carbon monoxide (CO), carbon dioxide (CO2), benzene, 1,3-butadiene, acetaldehyde and formaldehyde.

This study was the first of three EPA studies to investigate the effect of gasoline fuel parameters on hydrocarbon, nonmethane hydrocarbon, nitrogen oxides, benzene, formaldehyde, and acetaldehyde exhaust emissions of 1990 model year or equivalent vehicles. The fuel parameters tested in this program were oxygen concentration, Reid Vapor Pressure (RVP), ninety percent evaporative distillation temperature (T90), and sulfur concentration. Sulfur concentration was found to have the greatest effect on hydrocarbon and nitrogen oxide emissions. Increasing oxygen concentration and RVP reduction was found to reduce hydrocarbon emission more for high-emitting than normal-emitting vehicles. Oxygenate concentration was found to have a significant effect on aldehyde emissions.

Portable Emission Measurement Systems (PEMS) are used by the U.S. Environmental Protection Agency (EPA) to measure gaseous and particulate mass emissions from vehicles in normal, in-use, on-the-road operation to support many of its programs, including assessing mobile source emissions compliance, emissions factor assessment for in-use fleet modeling, and collection of in-use vehicle operational data to support vehicle simulation modeling programs. This paper discusses EPA’s use of Global Positioning System (GPS) measured altitude data and electronically logged vehicle speed data to provide real-world road grade data for use as an input into the Gamma Technologies GT-DRIVE+ vehicle model. The GPS measured altitudes and the CAN vehicle speed data were filtered and smoothed to calculate the road grades by using open-source Python code and associated packages.

With increasingly stringent light duty particulate emissions regulations, it is of great interest to better understand particulate matter formation. Helping to build the knowledge base for a thorough understanding of particulate matter formation will be an essential step in developing effective control strategies. It is especially important to do this in such a way as to emulate real driving behaviors, including cold starts and transients. To this end, this study examined particulate emissions during transient operation in a recent model year vehicle equipped with a GDI engine. Three of the major federal test cycles were selected as evaluation schemes: the FTP, the HWFET, and the US06. These cycles capture much of the driving behaviors likely to be observed in typical driving scenarios. Measurements included particle size distributions from a TSI EEPS fast-response particle spectrometer, as well as real-time soot emissions from an AVL MSS soot sensor.

Motor vehicle emission testing during on-road driving is important to assess a vehicle’s exhaust emission control design, its compliance with Federal regulations and its impact on air quality. The U.S. Environmental Protection Agency (EPA) has been developing new approaches to screen the characteristics of vehicle dynamic emission control behaviors (its operating signature) while driving both on-road and on-dynamometer. The so-called “signature device” used for this testing is equipped with an O2/NOx sensor, thermocouple and GPS to record dynamic exhaust NOx concentration, air fuel ratio-controlled tailpipe lambda (λ), tailpipe temperature and vehicle speed (acceleration). In the early EPA research, signature screening was used to characterize a vehicle’s PCM control behaviors (cause/effect bijectivity), which help distinguish operation in normal control state-space and abnormal state-space.

As part of the Midterm Evaluation of the 2017-2025 Light-duty Vehicle Greenhouse Gas Standards, the U.S. Environmental Protection Agency (EPA) developed simulation models for studying the effectiveness of stop-start technology for reducing CO2 emissions from light-duty vehicles. Stop-start technology is widespread in Europe due to high fuel prices and due to stringent EU CO2 emissions standards beginning in 2012. Stop-start has recently appeared as a standard equipment option on high-volume vehicles like the Chevrolet Malibu, Ford Fusion, Chrysler 200, Jeep Cherokee, and Ram 1500 truck. EPA has included stop-start technology in its assessment of CO2-reducing technologies available for compliance with the standards. Simulation and modeling of this technology requires a suitable model of the battery. The introduction of stop-start has stimulated development of 12-volt battery systems capable of providing the enhanced performance and cycle life durability that it requires.

The EPAct/V2/E-89 gasoline fuel effects program collected emissions data for 27 test fuels using a fleet of 15 high-sales cars and light trucks from the 2008 model year (all with port fuel injection). The test fuel matrix covered values of T50, T90, vapor pressure, ethanol content, and total aromatic content spanning ranges typical of market gasolines. Emission measurements were made over the LA92 cycle at a nominal temperature of 24°C (75°F). The resulting emissions database of 956 tests includes a particulate matter (PM) mass measurement for each. Emission models for PM fuel effects were fit based on terms for which the fuel matrix was originally optimized, with results published by EPA in a 2013 analysis report. This paper presents results of a subsequent modeling analysis of this PM data using the PM Index fuel parameter, and compares these models to the original versions.

Because of U.S. EPA regulatory actions and the National Academies National Research Council suggestions for improvements in the U.S. EPA emissions inventory methods, the U.S. EPA' Office of Transportation and Air Quality (OTAQ) has made a concerted effort to develop instrumentation that can measure criteria pollutant emissions during the operation of on-road and off-road vehicles. These instruments are now being used in applications ranging from snowmobiles to on-road passenger cars to trans-Pacific container ships. For the betterment of emissions inventory estimation these on-vehicle instruments have recently been employed to measure time resolved (1 hz) in-use gaseous emissions (CO₂, CO, THC, NO ) and particulate matter mass (with teflon membrane filter) emissions from 29 non-road construction vehicles (model years ranging from 1993 to 2007) over a three year period in various counties in Iowa, Missouri, and Kansas.

After initial trials on Homogeneous Charge Compression Ignition (HCCI) engine design and tests pursuing feedback control to avoid misfire and knocking over wide transient operation ranges, Engineers at the US Environmental Protection Agency's (EPA) National Vehicle Fuel and Emissions Laboratory identified the crucial engine state variable, MRPR (Maximum Rate of Pressure Rise) and successfully controlled a 1.9L HCCI engine in pure HCCI mode [1]. This engine was used to power a hybrid Ford F-150 truck which successfully ran FTP75 tests in 2004. In subsequent research, efforts have been focused on practical issues such as improving transient rate, system simplification for controllability and packaging, application of production grade in-cylinder pressure sensors, cold start, idling and calibration for ambient conditions as well as oxidation catalyst applications for better turbine efficiency and HC and CO emissions control.

A gasoline’s distillation profile is directly related to its hydrocarbon composition and the volatility (boiling points) of those hydrocarbons. Generally, the volatility profiles of U.S. market fuels are characterized using a very simple, low theoretical plate distillation separation, detailed in the ASTM D86 test method. Because of the physical chemistry properties of some compounds in gasoline, this simple still or retort distillation has some limitations: separating azeotropes, isomers, and heavier hydrocarbons. Chemists generally rely on chromatographic separations when more detailed and precise results are needed. High-boiling aromatic compounds are the primary source of particulate emissions from spark ignited (SI), internal combustion engines (ICE), hence a detailed understanding and high-resolution separation of these heavy compounds is needed.

Commercial, class-8 tractor-trailers were tested to develop a relationship between vehicle speed and fuel savings associated with trailer aerodynamic technologies representative of typical long-haul freight applications. This research seeks to address a concern that many long-distance U.S. freight companies hold that, as vehicle speed is reduced, the fuel savings benefits of aerodynamic technologies are not realized. In this paper, the reductions in fuel consumption were measured using the SAE J1231 test method and thru-engine fueling rates recorded from the vehicle’s electronic data stream. Constant speed testing was conducted on road at different speeds and corresponding testing was conducted on track to confirm results. Data was collected at four (4) vehicle speeds: 35, 45, 55, and 62 miles per hour. Two different trailer aerodynamic configurations were evaluated relative to a baseline tractor trailer.

This paper covers work performed for the California Air Resources Board and the United States Environmental Protection Agency by Southwest Research Institute. Emission measurements were made on nine types of off-road equipment with small (<19kW) spark-ignited engines including handheld and non-handheld equipment utilizing oxygenated and non-oxygenated fuels. Emission data was produced to augment ARB and EPA's off-road emission inventory. It was intended that this program provide ARB and EPA with emission test results they require for atmospheric modeling. The paper describes the equipment and engines tested, test procedures, emissions sampling methodologies, and emissions analytical techniques. Fuels used in the study are described, along with the emissions characterization results. The fuel effects on exhaust emissions and operation due to ethanol content and fuel components is compared.

This paper covers work performed for the California Air Resources Board and US Environmental Protection Agency by Southwest Research Institute. Emission measurements were made on four in-use off-road two-stroke motorcycles and all-terrain vehicles utilizing oxygenated and non-oxygenated fuels. Emission data was produced to augment ARB and EPA's off-road emission inventory. It was intended that this program provide ARB and EPA with emission test results they require for atmospheric modeling. The paper describes the equipment and engines tested, test procedures, emissions sampling methodologies, and emissions analytical techniques. Fuels used in the study are described, along with the emissions characterization results. The fuel effects on exhaust emissions and operation due to ethanol content and fuel components is compared.

The California Air Resources Board (CARB) adopted the Low Emission Vehicle (LEV) III regulations in January 2012, which lowered the particulate matter (PM) emissions standards for light-duty vehicles (LDVs) from 10 milligrams per mile (10 mg/mile) to 3 mg/mile beginning with model year (MY) 2017 and 1 mg/mile beginning with MY 2025. To confirm the ability to measure PM emissions below 1 mg/mile, a total of 23 LDVs (MY pre-2004 to 2009) were tested at CARB's Haagen-Smit Laboratory (HSL) (10 LDVs) and the United States Environmental Protection Agency's (US EPA) National Vehicle and Fuel Emissions Laboratory (NVEFL) (13 LDVs) using the federal test procedure (FTP) drive schedule. One LDV with PM emissions ranging from 0.6 - 0.8 mg/mile was tested at three CARB HSL test cells to investigate intra-lab and inter-lab variability. Reference, trip, and tunnel filter blanks were collected as part of routine quality control (QC) procedures.

To investigate the feasibility of various aerodynamic test procedures for the Phase 2 Greenhouse Gas (GHG) Regulations for heavy-duty vehicles in the United States, the US Environmental Protection Agency conducted, through Southwest Research Institute (SwRI), coastdown testing of several heavy-duty tractors matched to a conventional 53-foot dry-van trailer. Three vehicle configurations were tested, two of which included common trailer drag-reduction technologies. Air speed was measured onboard the vehicle, and wind conditions were measured using a weather station placed along the road side. Tests were performed on a rural road in Texas. One vehicle configuration was tested over several days to evaluate day-to-day repeatability and the influence of changing wind conditions. Data on external sources of road forces, such as grade and speed dependence of tire rolling resistance, were collected separately and incorporated into the analysis.

With ongoing concerns about the elevated levels of ambient air pollution in urban areas and the contribution from heavy-duty diesel vehicles, hybrid electric vehicles are considered as a potential solution as they are perceived to be more fuel efficient and less polluting than their conventional engine counterparts. However, recent studies have shown that real-world emissions may be substantially higher than those measured in the laboratory, mainly due to operating conditions that are not fully accounted for in dynamometer test cycles. At the U.S. EPA National Fuel and Vehicle Emissions Laboratory (NVFEL) the in-use criteria emissions and energy efficiency of heavy-duty class 8 vehicles (up to 36280 kg) can be evaluated under controlled conditions in the heavy-duty chassis dynamometer test.