Search Results

In modern engine design, downsizing and reducing weight while still providing an increased amount of power has been a general trend in recent decades. Traditionally, an engine design with superior NVH performance usually comes with a heavier, thus sturdier structure. Therefore, modern engine design requires that NVH be considered in the very early design stage to avoid modifications of engine structure at the last minute, when very few changes can be made. NVH design optimization of engine components has become more practical due to the development of computer software and hardware. However, there is still a need for smarter algorithms to draw a direct relationship between the design and the radiated sound power. At the moment, techniques based on modal acoustic transfer vectors (MATVs) have gained popularity in design optimization for their good performance in sound pressure prediction.

NVH development of light duty diesel engines require significant collaboration with the OEM as compared to medium duty and heavy duty diesel engines. Typically, competitive benchmark studies and customer expectations define the NVH targets at the vehicle level and are subsequently cascaded down to the powertrain level. For engine manufacturing companies like Cummins Inc., it is imperative to work closely with OEM to deliver on the NVH expectations. In certain situations, engine level NVH targets needs to be demonstrated in the OEM or 3rd party acoustic test facility for customer satisfaction or commercial purposes. Engine noise tests across different noise test facilities may introduce some variation due to differences in the acoustic test facilities, test hardware, instrumentation differences, etc. In addition, the engine itself is a major source of variation.

Component sound quality is an important factor in the design of competitive diesel engines. One component noise that causes complaints is the gear rattle that originates in the front-of-engine gear train which drives the fuel pump and other accessories. The rattle is caused by repeated tooth impacts resulting from fluctuations in differential torsional acceleration of the driving gears. These impacts generate a broadband, impulsive noise that is often perceived as annoying. In most previous work, the overall sound quality of diesel engines has been considered without specifically focusing on predicting the perception of gear rattle. Gear rattle level has been quantified based on angular acceleration measurements, but those measurements can be difficult to perform. Here, the emphasis was on developing a metric based on subjective testing of the perception of gear rattle.

Managing the injection rate profile is a powerful tool to control engine performance and emission levels. In particular, Common Rail (C.R.) injection systems allow an almost completely flexible fuel injection event in DI-diesel engines by permitting a free mapping of the start of injection, injection pressure, rate of injection and, in the near future, multiple injections. This research deals with the development of a network-based numerical tool for understanding operating condition limits of the Common Rail injector. The models simulate the electro-fluid-mechanical behavior of the injector accounting for cavitation in the nozzle holes. Validation against experiments has been performed. The model has been used to provide insight into the operating conditions of the injector and in order to highlight the application to injection system design.

Vehicle noise has reduced over the years due to the customer demand for quieter vehicles. As the background noises such as combustion noise, pumping noise, etc. have reduced, mechanical noises such as gear noise have become prominent and a major cause of customer complaints. Engine timing gear train uses gears for transferring torque to cam and accessory gears. As engines have become quieter by efforts to reduce the combustion noise, as well as, by moving away from mechanical fuel pumps to common rail fuel pumps, the gear train noise has come under increased scrutiny. Gear whine could be a result of multiple factors. Gear profile distortion is one of the factors. Gear torque variation also has a significant effect on gear whine. Operation of the accessory drives such as hydraulic pumps under variable loads and speeds, is one of the major challenges for resolving a gear whine issue in the engine gear train.

In recent years, the focus on engine parasitic losses has increased as a result of the efforts to increase engine efficiency and reduce greenhouse gasses. The engine gear train, used to time the valve system and drive auxiliary loads, contributes to the overall engine parasitic losses. Anti-backlash gears are often used in engine gear trains to reduce gear rattle noise resulting from the torsional excitation of the gear train by the engine output torque. Friction between sliding surfaces at the gear tooth is a major source of power loss in gear trains. The effect of using anti-backlash gears on the gear friction power loss is not well known. As a part of the effort to reduce parasitic losses, the increase in friction power loss in the Cummins ISX 15 gear train due to the anti-backlash gear was quantitatively determined by modifying the methods given in ISO 14179-2 to fit the anti-backlash gear sub-assembly.

Automotive timing gear trains, transmission gearboxes, and wind turbine gearboxes are some of the application examples known to use interference-fit to attach the gear to the rotating shaft. This paper discusses the interference-fit joint design and the finite element analysis to demonstrate the distortion. The mechanism of tooth profile distortion due to the interference-fit assembly in gear trains is discussed by demonstrating the before and after assembly gear profile measurements. An algorithm to calculate the profile slope deviation change is presented. The effectiveness of the computational algorithm to predict the distortion is demonstrated by comparing with measurements. Finally, steps to mitigate the interference assembly effects are discussed.

This paper presents an experimental setup and an equivalent FEM simulation methodology to accurately predict the response of Engine Control Module (ECM) assembly mounted on a commercial vehicle subjected to road vibrations. Comprehensive vibration study is carried out. It involved Modal characteristics determination followed by random vibration characterization of the ECM assembly. A hammer impact experiment is first performed in lab to estimate the natural frequencies and mode shapes of ECM assembly. Mounting conditions in test specimen are kept similar to the actual mounting settings on vehicle. Natural frequencies and mode shapes predicted from free vibration experiment are compared with finite element (FE) based modal analysis. The importance of capturing the assembly stiffness more accurately by incorporating pre-stress effects like bolt-pretension and gravity, is emphasized.

Due to increasing expectations for gasoline like sound quality, today's diesel engines for light and medium duty automotive markets needs to be carefully designed from NVH perspective. Typical engine operating conditions such as low idle, light tip in, tip out demand more attention as they are more prone to generating sound quality concerns. Any abrupt change in the noise signature may be perceived as a sign of malfunction and could have a potential to generate warranty claims. In this paper, an experimental investigation was carried out to determine the root cause of the transient oil pressure regulator buzz noise which occurred during no load transients at low engine speeds. The root cause of the objectionable noise was found to be associated with the impacts of the regulator plunger on the valve seat at certain engine speeds. Noise and vibration diagnostic tests confirmed that the plunger impacts at the seat caused the objectionable buzz noise.

This study is a continuation of previous work assessing the robustness of a Cummins XPI common rail injection system operating with gasoline-like fuel. All the hardware from the original study was retained except for the high pressure pump head and check valves which were replaced due to cavitation damage. An additional 400 hour NATO cycle was run on the refurbished fuel system to achieve a total exposure time of 800 hours and detect any other significant failure modes. As in the initial investigation, fuel system parameters including pressures, temperatures and flow rates were logged on a test bench to monitor performance over time. Fuel and lubricant samples were taken every 50 hours to assess fuel consistency, metallic wear, and interaction between fuel and oil. High fidelity driving torque and flow measurements were made to compare overall system performance when operating with both diesel and light distillate fuel.

An existing pass by noise data acquisition system was upgraded to provide the sophisticated data analysis techniques and test site efficiency required to comply with the current and future drive by noise regulations. Use of six sigma tool such as voice of the customer helped in defining the customer requirements which were then translated into the desired engineering characteristics using QFD. Pugh concept matrix narrowed down the best option suitable for the test site modifications taking into account the critical constraints such as test complexity, system cost & transparency to the existing drive by noise setup. Features of the new system include data telemetry, frequency analysis, portability and efficient data management through the use of advanced data acquisition system. Wireless mode of the data transmission helped significantly avoid most of the test site modifications, which in turn helped to reduce the overall system implementation cost.

Engine noise is one of the significant aspects of product quality for light and medium duty diesel engine market applications. Gear whine is one of those noise issues, which is considered objectionable and impacts the customer’s perception of the product quality. Gear whine could result due to defects in the gear manufacturing process and/or due to inaccurate design of the gear macro and micro geometry. The focus of this technical paper is to discuss gear whine considerations from the production plant perspective. This includes quick overview of the measurement process, test cell environment, noise acceptance criteria considerations. A gear whine case study is presented based on the data collected in the test cell at the engine plant. Gear whine data acquired on current product and next generation of prototype engines is analyzed and presented. This paper concludes by highlighting the lessons learned from the case study.

Wideband Acoustical Holography (WBH), which is a monopole-based, equivalent source procedure (J. Hald, “Wideband Acoustical Holography,” INTER-NOISE 2014), has proven to offer accurate noise source visualization results in experiments with a simple noise source: e.g., a loudspeaker (T. Shi, Y. Liu, J.S. Bolton, “The Use of Wideband Holography for Noise Source Visualization”, NOISE-CON 2016). From a previous study, it was found that the advantage of this procedure is the ability to optimize the solution in the case of an under-determined system: i.e., when the number of measurements is much smaller than the number of parameters that must be estimated in the model. In the present work, a diesel engine noise source was measured by using one set of measurements from a thirty-five channel combo-array placed in front of the engine.

The paper covers the design and development of a new 13L heavy-duty diesel engine intended primarily for heavy truck applications in China. It provides information on the specific characteristics of the engine that make it particularly suitable for operation in China, and describes in detail some of the design techniques that were used. To meet these exacting requirements, extensive use was made of Analysis-Led Design, which allows components, sub-systems and the entire engine, aftertreatment and vehicle system to be modeled before designs are taken to prototype hardware. This enables a level of system and sub-system optimization not previously available. The paper describes the emissions strategy for China, and the physical design strategy for the new engine, and provides some engine performance robustness details. The engine architecture is discussed and the paper details the analysis of the major components - cylinder block, head, head seal, power cylinder and bearings.

A head gasket is a component that sits between the engine block/liner and cylinder head(s) in an internal combustion engine. Its purpose is to seal high pressure combustion gasses in the cylinders and to seal coolant and engine oil. It is the most critical sealing application in an engine. As a general practice, the load deflection(L/D) characteristic is generated by the gasket manufacturer for edge molded or composite gasket types. However, in the case of a solid-sheet metallic gasket, where the gasket is expected to undergo localized yielding to provide adequate conformance and sealing, usually supplier may not be able to provide the required L/D curve due to difficulties to experimentally separate the large loads and small displacements from the elastic loads and deflections of the experimental apparatus. In absence of L/D curve, the typical analysis approach is to model gasket as 3D continuum elements available in ansys by considering nonlinear material and frictional contacts.

Diesel fuel spray characteristics are thought to depend on cavitation inside the fuel injector nozzles. These nozzles are very small and the fuel flow is very fast, making experimental observation very difficult. Numerical simulation of the two-phase flow is hindered by the severe density difference between the liquid and vapor as well as the existence of complex free surfaces. Recent experimental and numerical advances are now permitting visual observation of real-scale cavitating flow and two-dimensional simulation of the cavitating flow. In contrast to past work, we have chosen to study asymmetric nozzle flow. Asymmetry is more representative of real injector geometry than symmetric nozzles and may yield more reproducible results. Experimental runs of 1 mm long nozzles were made at upstream pressures up to 120 bar with downstream pressures from 1 to 50 bar. Photographs of planar asymmetric nozzles revealed complex transient structures on the fuel-vapor interface.

This paper demonstrates the use of a system level model that includes torsional models of a Cummins diesel engine and an Allison transmission to study and improve system NVH behavior. The study is a case where the two suppliers of key powertrain components, Cummins Inc. and Allison Transmission Inc., have collaborated to solve an observed NVH problem for a vehicle customer. A common commercial tool, Siemens' AMESim, was used to develop the drivetrain torsional system model. This paper describes a method of modelling and calibration of baseline engine and transmission models to identify the source of vibration. Natural frequencies, modal shapes, and forced response were calculated for each vehicle drive gear ratio to study the torsional vibration. Several parametric studies such as damping, inertia, and stiffness were carried out to understand their impact on torsional vibration of the system.

Development of quick and efficient numerical tools is key to the design of industrial machines. While Computational Fluid Dynamics (CFD) techniques based on Navier Stokes (N-S) and Lattice Boltzman methods are becoming popular, predicting aeroacoustic behavior for complex geometries remains computationally intensive for design process and iteration. The goal of this paper is to evaluate application Navier-Stokes approach coupled with Ffowcs Williams and Hawkings (FW-H), and Broad-band Noise Model (BNS) to evaluate noise levels and predict design direction for industrial applications. Steady-state RANS based approaches are used to evaluate under-hood cooling performance and fan power demand. At each design iteration, noise levels and strength of noise source are evaluated using Gutin’s and broad-band noise models, respectively along with cooling performance. Each design feature selected for the final design has lower fan power and noise level with improved cooling.