Search Results

OBD system requirements were first developed by the California Air Resources Board, the U.S. Environmental Protection Agency, and the European Commission. New OBD requirements should be as consistent as possible with existing requirements to maximize reliability and to minimize system complexity, proliferation of configurations, and consumer cost. New OBD requirements from around the world are briefly reviewed and most are consistent with the original U.S. and European requirements. Worldwide OBD requirements are being further harmonized under the United Nations, Economic Commission for Europe, World Forum for Harmonization of Vehicle Regulations (WP29). Presenter David H. Ferris, General Motors Company

The foundation of many production aircraft assembly facilities is a more dynamic and unpredictable quantity than we would sometimes care to admit. Any tooling structures constructed on these floors, no matter how thoroughly analyzed or well understood, are at the mercy of settling and shifting concrete, which can cause very lengthy and costly periodic re-certification and adjustment procedures. It is with this in mind, then, that we explore the design possibilities for one such structure to be built in Belfast, North Ireland for the assembly of the Shorts C-Series aircraft wings. We evaluate the peak floor pressure, weight, gravity deflection, drilling deflection, and thermal deflection of four promising structures and discover that carefully designed pivot points and tension members can offer significant benefits in some areas.

Many manufacturing companies want to apply AFP technology to complex high-curvature part shapes. As new AFP machine technologies are developed to specifically apply material over complex shapes, new and innovative NC programming approaches are needed to successfully, reliably, and accurately apply material with good consolidation, while meeting the fiber direction and coverage requirements. A big issue with AFP is the production rate vs. part complexity. Most complex shapes can be created with a single .125? wide strip (tow) of material. But the production time would be impractically long. So machine builders create 6, 8, 16, even 32 tow AFP heads, and use the widest tow possible for the highest laydown rates. But then wide compaction rollers on these systems have difficulty consolidating material over curved surfaces, and the minimum steering radius of wider tows challenge the software?s ability to meet the layup requirements.

Revisions to the California OBD-II diesel regulations required many updates to various SAE and ISO on-board diagnostic standards; these include major revisions to SAE J1979, J1699-3, J2012 and J1930. This presentation is intended to review the background for these changes as well as the revisions made in these documents. Presenter Robert Gruszczynski, Volkswagen of America

Update on light-duty regulations. Presenter Michael J. McCarthy, California Air Resources Board

Automakers, suppliers, public agencies, interest groups and others are increasingly embracing the environment as one of the dominant forces in the US automotive market. All parties have a strong vested interest in understanding how environmental concerns will influence design, production, marketing and usage of tomorrow�s vehicles. A common need of all parties is independent and actionable information to enable them to make better decisions and have the greatest chance of being successful in this uncertain future. Four factors - an uncertain economic climate; a constantly changing governmental regulatory system; advancements in powertrain technology; and ever-present environmental concerns - continue to shape the automotive landscape. While automakers are focused on developing alternative powertrains and alternative fuel options for an increasingly �green� vehicle market, J.D.

Alyson Lyon, Executive Leadership Coach, explains how the most successful people manage their time. Members can view the full version by logging into the Member Connection here Not a Member? Get a taste of the Member Connection and join at connection.sae.org.

Watch for tips from experts in the mobility industry on how to live in harmony. Members can view the full panel session by logging into the Member Connection here Not a Member? Join us today at sae.org/join.

There are now a wide variety of Hybrid and Electric Vehicles in or near production. They reduce or displace petroleum consumption with of various combinations of conventional IC engine, mechanical transmission, liquid fuel storage, electrical energy storage, electrical and electro-mechanical energy conversion, and vehicle-to-grid energy interface. These Electrified types of vehicles include Mild Hybrid, Full Hybrid, Plug-In Hybrid, Extended Range Electric, and Battery Electric. Some types differ in their actual usability for the real mixes of driving trips, and further that differ in their effectiveness to reduce or displace fuel in actual real world driving use. Vehicle size is also a factor in total vehicle utility in transporting people. If we may segment drivers by their driving needs, in each segment, we see a particular type of electrified vehicle that is better suited than others at minimizing fuel cost and petroleum consumption for the purposes of transporting people.

Gasoline engines continue to suffer from significant pumping losses despite decades of effort focused on reducing throttling. Honeywell Turbo has developed a throttle with an integrated turbine/generator that generates electricity by recovering pumping work. This energy offsets power normally provided by the crank driven alternator, thereby saving fuel. It integrates well with modern electrical systems which employ smart charging and idle stop strategies. The ThrottleCharger provides fuel economy benefits up to 5% over federal test cycles and in real world conditions. Presenter Mike Guidry, Honeywell Int'l (Turbo Technologies)

The presentation describes the aerodynamic development and optimization process of the three different new models of the Audi A6/A7 family. The body types of these three models represent the three classic aerodynamic body types squareback, notchback and fastback. A short introduction of the flow structures of these different body types is given and their effect on the vehicle aerodynamic is described. In order to achieve good aerodynamic performance, the integration into the development process of the knowledge about these flow phenomena and the breakdown of the aerodynamic resistance into its components friction- and pressure drag as well as the induced drag is very important. The presentation illustrates how this is realized within the aerodynamic development process at Audi. It describes how the results of CFD simulations are combined with wind tunnel measurements and how the information about the different flow phenomena were used to achieve an aerodynamic improvement.

Simulation-based tolerance analysis is the accepted standard for dimensional engineering in aerospace today. Sophisticated 3D model-based tolerance analysis processes enable engineers to measure variation in complex, often large, assembled products quickly and accurately. Best-in-class manufacturers have adopted Quality Intelligence Management tools for collecting and consolidating this measurement data. Their goal is to completely understand dimensional fit characteristics and quality status before commencing the build process. This results in shorter launch cycles, improved process capabilities, reduced scrap and less production downtime. This paper describes how to use simulation-based approaches to correlate the theoretical tolerance analysis results produced during engineering simulations to actual as-built results. This allows engineers to validate or adjust as-designed simulation parameters to more closely align to production process capabilities.

As a result of recommendation from the Augustine Panel, the direction for Human Space Flight has been altered from the original plan referred to as Constellation. NASA's Human Exploration Framework Team (HEFT) proposes the use of a Shuttle Derived Heavy Lift Launch Vehicle (SDLV) and an Orion derived spacecraft (salvaged from Constellation) to support a new flexible direction for space exploration. The SDLV must be developed within an environment of a constrained budget and a preferred fast development schedule. Thus, it has been proposed to utilize existing assets from the Shuttle Program to speed development at a lower cost. These existing assets should not only include structures such as external tanks or solid rockets, but also the Flight Software which has traditionally been a ?long pole? in new development efforts. The avionics and software for the Space Shuttle was primarily developed in the 70's and considered state of the art for that time.

A series of flight tests were conducted to design and evaluate a Combined Vision System (CVS) that integrates a forward looking infrared video image with synthetic vision on a primary flight display. System features included colorizing the video image to mesh with the synthetic terrain background, decluttering the approach symbology to facilitate the detection of the approach lights and runway markings, creating a semi-transparent IR sky to ensure continuous situational awareness of the surrounding terrain, and annunciating the decision height to facilitate the transition to the actual runway environment. Over 100 approaches were flown during three flight test sessions. For the first flight test session pilots reviewed early CVS proofs of concept on Honeywell's Citation Sovereign.

“Spotlight on Design” features video interviews and case study segments, focusing on the latest technology breakthroughs. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. In the episode “Diagnostics and Prognostics: Proactive Maintenance and Failure Prevention” (21:04), Delphi engineers explain how they leverage the growing number of sensors and computing power in vehicles to diagnose and proactively solve emerging mechanical or electronic problems, before a breakdown occurs. This video also looks at the next generation of automotive telematics, with HEM Data demonstrating how in-vehicle data acquisition is used to monitor the inner workings of vehicles.

“Spotlight on Design” features video interviews and case study segments, focusing on the latest technology breakthroughs. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. In the episode “Composite Materials: Advanced Materials and Lightweighting” (30:20), Molded Fiber Glass Companies, known for its deep involvement in the creative development of the molded fiberglass process for the Corvette, demonstrates the manufacturing of sheet molded composite for fiberglass parts. Tanom Motors introduces the Tanom Invader, a blend between an automobile and a motorcycle made exclusively with composite materials. Finally, Euro-Composites demonstrates the manufacturing of honeycomb core material made out of aramid paper and phenolic resin used in aircraft structures.

“Spotlight on Design” features video interviews and case studies, focusing on technology breakthroughs, hands-on testimonials, and the importance of fundamentals. Viewers are virtually taken to industry labs and research centers to learn how design engineers solve real-life problems. These challenges include enhancing product performance, reducing costs, improving quality and safety, while decreasing environmental impact, and achieving regulatory compliance. In the episode “Additive Manufacturing: 3D Printing in the Automotive Industry” (20:00), engineers from Fiat Chrysler Corporation (FCA) explain the importance of using 3D printing to test multiple design scenarios and develop solutions that can be quickly evaluated on test tracks. And Local Motors shows how it builds a vehicle from the ground up with a 3D printer, and without a traditional assembly line.

In “The Impact of Additive Manufacturing in Automotive Applications”, a professor from Kettering University explains why additive manufacturing will be a game changer for car makers, and how process control is one of the biggest challenges ahead. An engineer at Local Motors in Arizona shows how the company builds its cars using a large-scale 3D printer, including how a variety of materials is being evaluated for optimal performance in this type of application. The episode highlights: The expected positive impact of AM on smaller car makers and suppliers The key difference between small 3D printers and large-scale ones The need to find the best possible material combination so vehicles that are #D-printed are as safe as traditional ones Also Available in DVD Format To subscribe to a full-season of Spotlight on Design, please contact SAE Corporate Sales: CustomerSales@sae.org or 1-888-875-3976.

“Spotlight on Design: Insight” features an in-depth look at the latest technology breakthroughs impacting mobility. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. Extreme environment sensors require extreme environment cables that can reliably perform in temperatures up to 2300° F, withstand intense vibration, and have extraordinary strength. In the episode “Sensors: Noise Avoidance and Cable Manufacturing” (8:53), an engineer at Meggitt Sensing Systems demonstrates the intricate process of developing cable for sensors used in these situations.

“Spotlight on Design: Insight” features an in-depth look at the latest technology breakthroughs impacting mobility. Viewers are virtually taken to labs and research centers to learn how design engineers are enhancing product performance/reliability, reducing cost, improving quality, safety or environmental impact, and achieving regulatory compliance. Telematics, the convergence of telecommunications and informatics, uses electronic and computer technology built in to the vehicle to provide vehicle tracking, satellite navigation, wireless technology, and diagnostic information. In the episode “Diagnostics and Prognostics: Telematics Deep Dive” (8:09), an engineer from Delphi’s Telematics program discusses the advantages and challenges of telematics devices for the automotive industry, demonstrates the installation of an aftermarket telematics device, and shows how telematics can enhance diagnostics and preventative maintenance.