Search Results

Assuming rigid body motion, recorded acceleration and recorded roll rates at the center of gravity, equations are used to calculate the local three-dimensional accelerations at hypothetical seating positions' Emergency Locking [seat belt] Retractors (ELR) during a steer induced rollover crash. For a threshold of 0.7 g, results demonstrated that intervals in the vehicle's response that may cause the ELR's inertial sensor to move into a neutral zone were limited to localized high magnitude negative vertical acceleration events during the rollover segment with a median duration of 4 ms, average duration of 4.8 ms and a maximum calculated duration of 31.7 ms. Changing the threshold to 0.35 g reduced the interval count by 70 percent and maximum duration by approximately 50 percent.

Plane strain bending (e.g. bending about a straight line) is a major sheet forming operation and it is practiced as brake bending (air bending, U-die, V-die and wiping-die bending). Precise prediction of springback is the key to the design of the bending dies and to the control of the process and press brake to obtain close tolerances in bent parts. In this paper, reliable mathematical models for press brake bending are presented. These models can predict springback, bendability, strain and stress distributions, and the maximum loads on the punch and die. The elasto-plastic bending model incorporates the true (nonlinear) strain distribution across the sheet thickness, Swift's strain hardening law, Hill's 1979 nonquadratic yield criterion for normal anisotropic materials, and plane strain deformation mode.

Liver trauma research suggests that rapidly increasing internal pressure plays a role in liver injury. Previous work has shown a correlation between pressure and liver injury in pressurized ex vivo human livers when subjected to blunt impacts. The purpose of this study was to extend the investigation of this relationship between pressure and liver injury by testing full-body post-mortem human surrogates (PMHS). Pressure-related variables were compared with one another and also to previously proposed biomechanical predictors of abdominal injury. Ten PMHS were tested. The abdominal vessels were pressurized to physiological levels using saline, and a pneumatic ram impacted the right side of the specimen ribcage at a nominal velocity of 7.0 m/s. Specimens were subjected to either lateral (n = 5) or oblique (n = 5) impacts, and the impact-induced pressures were measured by transducers inserted into the hepatic veins and inferior vena cava.

Legislation pertaining to automobile emissions has caused an increased focus on the cold-start performance of internal combustion engines. Of particular concern is the period of time before all available sensors become active. Present engine control strategies must rely on methods other than feedback control while these sensors are not active. Without feedback control during this critical period, engine emissions performance is not optimized. These conditions cause difficulty in performing comprehensive cold-start experiments. For these reasons, we have developed several methods for feedback control during cold-start to aid in laboratory investigations of engine emissions phenomena.

In this paper, we propose an IC engine fuel system diagnostic algorithm based on a discrete-event nonlinear observer using the production oxygen sensor. A mean value engine model is used to describe the engine dynamics. A procedure for designing the discrete event based observer is presented and applied to estimate important engine variables using the measured binary oxygen sensor output. The estimated variables are then used to perform diagnostics of the fuel system of the IC engine. Experimental results on a multi-cylinder production engine are presented to demonstrate the effectiveness of the proposed method.

The motivation of this paper is inverse estimation of the material properties for sheet metals subjected to cyclic loading. Cyclic three-point bending tests are performed. Bending moments are computed from the measured data, namely, punch stroke, punch load, bending strain and bending angle. Bending moments are also calculated based on the selected material model in which normal anisotropy and combined hardening are considered. Material parameters are identified by minimizing the difference between these two bending moments. Modified Levenberg-Marquardt method is used in the optimization procedure. Stress-strain curves are generated with the optimized material parameters.

Reported tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys indicate that those values depend on the size and shape of the test samples and their global porosities. This paper reviews the mechanical properties reported in the open literature for these die cast alloys and indicates that section thickness and global porosity are inadequate for predicting the tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys.

For some vehicle dynamics applications, an estimate of a vehicle's center of gravity (cg) height and mass moments of inertia can suffice. For other applications, such as vehicle models and simulations used for vehicle development, these values should be as accurate as possible. This paper presents several topics related to inertial parameter estimation and measurement. The first is a simple but reliable method of estimating vehicle mass moment of inertia values from data such as the center of gravity height, roof height, track width, and other easily measurable values of any light road vehicle. The second is an error analysis showing the effect, during a simple static cg height test, of vehicle motion (relative to the support system) on the vehicle's calculated cg height. A method of accounting for this motion is presented. Similarly, the effects of vehicle motion are analyzed for subsequent mass moment of inertia tests.

We consider a vehicle-roadway system where the control of vehicle movement is based on the instrumentation located both in the vehicle and the roadway. In addition to the sensors which are used for obtaining the information on the vehicle, a radar based sensor system is used for providing information on the position of the car relative to a vehicle ahead, and with respect to a reflective strip placed on the road. The roadway traffic includes standard vehicles with no automatic control as well as the vehicles with automatic control units. Communication between the vehicles is not considered. For longitudinal control, we consider an Radar Based Cruise Control problem where the main goal is to maintain a desired speed set by the driver. At the same time, the controller will decelerate the vehicle if the distance and/or the relative speed between the controlled vehicle and the vehicles traveling in front are below certain limits.

There have been a number of papers written about the dynamic effects of low speed front to rear impacts between motor vehicles during the last several years. This has been an important issue in the field of accident analysis and reconstruction because of the frequency with which the accidents occur and the costs of injuries allegedly associated with them. Several of these papers have discussed the importance of the coefficient of restitution in the accelerations and speed changes that the vehicles undergo in such impacts. These discussions often include data showing the measured restitution for impacts involving various bumper types and closing speeds. However, in most of these studies, the impacts are controlled so that direct bumper to bumper impacts occur. This paper will present the results of several rear impact tests with non-standard impact configurations.

The handling, stability, and rollover resistance of vehicles is presently being studied by both the automotive industry and the National Highway and Traffic Safety Administration (NHTSA). However, to study the handling and rollover behavior of each vehicle on the road is not feasible. The ability to categorize and compare the rollover and handling behavior of various vehicles is a subject of considerable research interest. This paper examines the possibility of characterizing vehicle classes through the use of a three degree-of-freedom linear model. Initially, segregation is studied by evaluating the eigenvalue location in the complex domain for vehicle sideslip velocity, yaw rate, and roll angle. Then the influence of numerator dynamics on vehicle behavior is studied and vehicle class segregation is attempted through evaluation of the amplitude ratio of the frequency responses for sideslip velocity, yaw rate, and roll angle.

Current emission control systems utilize a catalytic converter employing a three-way catalyst (TWC), composed of a mixture of noble metals to minimize the three main pollutant classes of NOx, CO, and HC. The TWC is most efficient when the air-to-fuel ratio (A/F) is at stoichiometry (i.e. A/F ≈ 14.7). The stoichiometric set-point region is maintained by the use of oxygen sensors composed of the solid-electrolyte yttria stabilized zirconia (YSZ) in an electronic feedback loop. As combustion gets leaner a different exhaust sensor can be utilized to give a measure of the level of pollutants. A NOx sensor is an alternative for an oxygen sensor that can be used for feedback control of engine combustion or exhaust NOx traps. A solid electrolyte disk composed of YSZ having two Pt electrodes with one being covered by a microporous zeolite material was tested as a sensor for combustion produced gases such as NO and NO2 in the presence of O2.