Search Results

Instantaneous combine grain yield monitors need to provide reliable yield measurements since yield as a function of location is key information needed to manage fields by management zones. A scale and a yield monitor measured the same stream of grain and provided similar results when compared to each other. Data from either device may be misinterpreted if care in calibration and operation is not taken. Careful operators who pay attention to calibration, maintenance, and manufacturer's instructions will be required.

It is the goal of this paper, to discuss the impact of electronics on modern day commercial vehicles an buses. Seen from the position of advanced engineering of an European commercial vehicle manufacturer, the emphasis will be placed on the mechanical-electronical system itself, rather than the electronics themselves. User friendly, logic protected systems will minimize operator unfamiliarity and misapplication and will offer not only component control, but shortly the integration of all of these subsystems in the total vehicle control. Total vehicle control will be the ultimate result, when the driver, the truck and the environment are brought together. Such vehicles will be more responsive, safer and easier to drive than today's commercial vehicles and buses and offer a cost effective utilization of these new technologies to the customer.

The quality and availability of distillate fuels in the coming decades has become an increasing concern to the U.S. Navy. In response, the Energy Research and Development Office of the David Taylor Naval Ship Research and Development Center (DTNSRDC) has conducted a worldwide survey of commercial marine fuels. An effort was made to obtain 50 commercial marine fuel samples from various suppliers worldwide. The purpose of the survey was to assess the current quality of available fuels by analytically characterizing each of the fuel samples obtained. This assessment consisted of the measurement of more than 44 fuel properties. This paper contains a summary of the analytical results which were obtained. In addition, the current analytical results are compared with refinery specifications, with the current Navy specification, and with the results of a similar survey conducted in 1983. Finally, the resulting conclusions and recommendations are presented.

United States construction equipment manufacturers are subject to a maze of product-oriented regulations in marketing their U.S.-built products in foreign countries. These same obstacles face their foreign-built products. In the past, these foreign regulations were more apt to be trade barriers to protect domestic markets than bonafide regulations to protect the users. These trade barriers are gradually being lifted because manufacturers in virtually all countries have now expanded beyond their domestic markets. Thus, the same manufacturers that formerly encouraged trade barriers must now cope with them. This expansion of markets now encourages the elimination of trade barriers and the harmonization of regulations. For the future, regulations will be retained and expanded. They will, however, be harmonized with international voluntary standards rather than having different regulations for each country.

The idea of a world truck is a fascinating challenge - whereas cars are purchased more or less as seen; truck purchasers demand more individual configurations. In national and global terms, that means a highly complex truck market. Historically, a few European and North American manufacturers produced almost all the trucks for the world market. That changed through the 60's and 70's, with more local assembly plants around the world and increasing worldwide manufacturing capabilities. Concurrently, international component design standards have made some progress towards compatibility. Much greater co-operation is needed, however, before a genuinely international set of standards can be applied. As the task assigned to trucks is the same worldwide, namely to transport goods from A to B; it should be desirable and possible to work towards a greater commonality of vehicle - to ultimately achieve a world truck. The only unknown is the time scale.

Standardization and “Zero-Defects” are buzz-words among today's truck manufacturers. Electrical components is an area where these words must become reality. Components costing less than 1% of the final truck price should not cause problems for the end user or the manufacturer. The way to insure this is communication and design. Design out problems with new components.

Since 1992, Caterpillar has invested millions of dollars to purchase CAD software, and spends nearly $2M per year keeping its engineers up-to-date, via instructor lead training (ILT), as new enhancements are introduced. Periodic upgrades to the software also require huge resource (people, costs) commitments for the planning and execution of the training requirements required for a large global workforce. This paper will examine gaps uncovered in the efficiency and effectiveness of the current training process, and the cultural change required as a result of switching from an instructor led environment to a completely web-based solution, which, once deployed, had promised to change the way Caterpillar approached training for the future. The proposed change promised to improve human resource capability by utilizing new technological capabilities, and resulted in improvements in organizational capabilities as well.

HIGH output per cubic inch of piston displacement is desirable not alone for the purpose of being able to transport more payload faster, but more particularly for the invariably associated byproduct of lower specific fuel consumption, and especially at road-load requirements. The only way of accomplishing this purpose is through the use of higher compression ratios, and the limiting factors for this objective are fuel distribution and the operating temperatures of the component parts. A manifold is proposed which not only definitely improves distribution at both full and road loads, but has the inherent additional advantage of reducing the formation of condensate, thus still further facilitating a reduction in road-load specific fuel consumption. Hydraulic valve lifters, obviation of mechanical and thermal distortion, and controlled water flow are the essentials in improved cooling.

The paper attempts to determine which traction model best fits with experimental data for a romanian lugged tractor tire. Different models for predicting net traction and traction efficiency for off-road conditions were considered. These models assume different tire-ground pressure distributions (constant, parabolic) over the undertread area and different contact patch length calculations. Experiments were conducted and the results were compared to the theoretical data. Two of the models are the best fit with the experimental data; both models assumed a parabolic pressure distribution over the undertread.

New technology placed on specific components within the wheel end system, required modifications to existing tapered wheel bearing adjustment procedures. A new method for vehicles, which use tapered roller bearings, required a procedure addressing new technologies for the wheel end system. OEM and service technicians would benefit from concise procedures. Technologies engineered and developed for ABS (Anti-skid Brake Systems), extended brake blocks and synthetic lubricants, required research for the data base. Research to optimize the operating environment through improved maintenance procedures helped in achieving optimum wheel system operation. A tapered wheel bearing adjustment procedure and visual chart are the results profiting the vehicle manufacturers and field service technicians.

This paper discusses the relationship between users of construction equipment and the manufacturers and dealers of the equipment The people involved in this relationship are the deciding factors in whether all participants are satisfied, as the people are responsible ultimately for the product The paper points out that the major qualities necessary in the considerations behind a user's satisfaction with a manufacturer's product are those belonging to people, ingenuity, improvement, and integrity. Examples are shown from the user's point of view of the need for these qualities, of which integrity is the most important.

Welding residual stress is one of the primary factors responsible for cracking at the access hole interface between the flange and web plate of welded heavy W-shapes. During multi-pass welding, cracks can be found in either the flange plate or the web plate, depending upon welding sequence, joint details and access hole size. In this study, an integrated numerical and experimental investigation was conducted to evaluate the effects of welding parameters and joint geometry on the magnitude and distribution of residual stresses in thick-section butt joints. The results provide guidelines for improved design for welding of heavy W-shapes.

Nowadays, developing web (World Wide Web) engineering is considered to be a top priority task in many companies. A corporate web information center with broad coverage to support a company's worldwide engineering activities can make the product development and customer support more efficient. First, the archived, readily available product information, knowledge database, and user friendly engineering tools can ease up the more ever demanding engineering jobs. Second, the convenient information storage, retrieval systems and hyperlinks on the web should ensure effective communications among engineers, customers, and suppliers. However, without in-depth planning, the full benefits of web engineering cannot be realized. To be effective, other companion engineering programs must also be instated. This paper reviews the experience we have gained in utilizing web engineering for product development and customer support.

Abstract - The Warrior Injury Assessment Manikin (WIAMan) was developed to assess injury in Live Fire Test and Evaluation (LFTE) and laboratory development tests of vehicles and vehicle technologies subjected to underbody blast (UBB) loading. While UBB events impart primarily vertical loading, the occupant location in the vehicle relative to the blast can result in some inherent non-vertical, or off-axis loading. In this study, the WIAMan Technology Demonstrator (TD) was subjected to 18 tests with a 350g, 5-ms time duration drop tower pulse using an original equipment manufacturer (OEM) energy attenuating seat in four conditions: purely vertical, 15° forward tilt, 15° rearward tilt, and 15° lateral tilt to simulate the partly off-axis loading of an UBB event. The WIAMan TD showed no signs of damage upon inspection. Time history data indicates the magnitude, curve shape, and timing of the response data were sensitive to the off-axis loading in the lower extremity, pelvis, and spine.

NEARLY 300 fleet operators were questioned by Mr. Laurie to gather data for this paper on what features the users of trucks would like to have the manufacturers incorporate in post-war trucks. The cooling system is one important item that came in for its share of criticism. For example, maintaining the proper coolant level is most important, and yet many of today's systems require filling into the filler neck before the liquid level can be seen. Petcocks or sight gages properly installed could solve this problem, according to Mr. Laurie. Accessibility for maintenance should also be improved in the post-war truck. Some of today's trucks have batteries that are not located for ease of servicing and spark plugs that it is almost impossible to remove and replace. Improvements should also be possible in cold starting of the engine, based on the experience of the Army in cold climates.

Door slam test is one of the important durability tests in door design and development. Door requires to meet certain performance requirements like it should close properly (no metal to metal contact), there should not be any leakage, and closing operation should be smooth & with minimal effort and it should survive the life of the vehicle. Virtual simulation of door slam test, correlation with physical test results and effect of various parameters like seals stiffness are demonstrated in this study. Slam Analysis was carried out in LS-Dyna solver before physical test. This not only helped in avoiding initial structural design flaws, but also helped us in deciding door latch position, effect of mass distribution in the door and study of force distribution between primary seal, secondary seal and door latch. Primary and secondary seals played a critical role in the analysis. An intended length of both the seals was tested first to get its stiffness curve.

As competitive pressures in the automotive industry continue to increase the need for reduction in product development time, OEM's are searching for ways to eliminate non-valued added activities. Today, still too much time is devoted to the laborious process of manipulation of CAD geometry in the advanced stages of a program in order to develop feasibility for emerging design themes, involving the packaging and function of vehicle systems. Technology is being developed that will eliminate much of the tedium currently involved in this design engineering process. As theme iterations or packaging changes occur, CAD models that intelligently link the theme, the packaging, and the engineering “rules” will automatically “morph” into new designs. This Morphing process will execute CAD model changes according to engineering rules that are considered to be industry best practices.

The main objective of this paper is to present the different methods of pavement dimensioning, applied on the Brazilian roads, in order to compare the loads used in the calculation with a real application. It has been used a 4×2 vehicle with the maximum load distribution allowed in Brazil (6 tons in the front axle / 10 tons in the rear axle). It has been instrumented the rear axle with strain gauges to simulate it as a load cell. Measurements were done on a real urban application (Curitiba city - Brazil). Results showed significant differences between the load used in the Brazilian pavement dimensioning methodology and the dynamic vertical load, which could have a direct impact on the pavement lifetime. This paper was supported by three different agency / companies: UNICAMP, Volvo do Brasil and Meritor do Brasil Sistemas Automotivos Ltda.

Vehicle mission simulation is one component of a system designed to optimize selection and operation of on-highway vehicles. The focus of vehicle mission simulation is on equipment specification. It can predict the physical and financial performance of equipment alternatives, identify opportunities and correct problems before a truck is purchased.