Search Results

To get a better understanding of the characteristics of the high pressure gasoline sprays impinging on a wall, a fundamental study was conducted in a high-temperature high-pressure constant volume vessel under the simulated engine conditions of in-cylinder pressures, temperatures, and wall temperatures. The injection pressure was varied from 20 to 120 MPa. The spray tip penetration, vapor mass distribution, and vaporization rate were quantitatively measured with the laser absorption-scattering (LAS) technique. The velocity fields of the wall-impinging sprays under vaporizing conditions were measured with the particle image velocimetry (PIV) technique using silicone oil droplets as tracers. The effects of injection pressure and spray/wall interactions on spray characteristics were investigated. The results showed that the increased injection pressure improved penetration, vaporization, and turbulence of the sprays.

Three-Dimensional visualization technique based on volume rendering method has been developed in order to translate a calculated result of diesel combustion simulation into an realistically spray and flame image. This paper presents an overview of diesel combustion model which has been developed at Hiroshima University, a description of the three-dimensional visualization technique, and some examples of spray and flame image generated by this visualization technique.

The injection amount per stage in a multiple injection strategy is smaller than a conventional single-stage injection. In this paper, the effect of the injection amount (0.27mg, 0.89mg, 2.97mg) under 100MPa injection pressure and the effect of injection pressure (100MPa, 150MPa, 170MPa) under different injection amounts (0.27mg, 2.97mg) on the spray and mixture formation characteristics were studied by analyzing the vapor/liquid phase concentration distributions obtained under various conditions via using the tracer LAS technique. The spray was injected into a high-pressure and high-temperature constant volume vessel by using a single-hole nozzle with a diameter 0.133mm. The higher the injection pressure with a smaller injection amount is, the shorter the spray tip penetration and leaner air-fuel mixture occur. The combustion processes had been examined by a high-speed video camera with the two-color pyrometry method.

An experimental and numerical study was conducted on the spray and mixture properties of a hole-type injector for direct injection (D. I.) gasoline engines. The Laser Absorption Scattering (LAS) technique was adopted to simultaneously measure the spatial concentration distributions and the mass of the liquid and vapor phases in the fuel spray injected into a high-pressure and high-temperature constant volume vessel. The experimental results were compared to the numerical calculation results using three-dimensional CFD and the multi-objective optimization. In the numerical simulation, the design variable of the spray model was optimized by choosing spray tip penetration, and mass of liquid and vapor phases as objective functions.

Different ethanol-gasoline blended fuels, namely the E0 (100% gasoline), E85 (85% ethanol and 15% gasoline mixed in volume basis) and E100 (100% ethanol) were injected by a valve-covered-orifice (VCO) hole-type nozzle in a condition simulating the near top dead center (TDC). Two typical injection pressures of 10 and 20MPa were adopted to clarify the spray and flame behaviors. The correlation of the upstream unburned fuel and the flame propagation was analyzed by the high-speed imaging of shadowgraph. Moreover, the effects of ignition timing and location on the flame propagation were discussed based on the imaging of OH* chemiluminescence.

Reduction of orifice diameter of nozzle is advantageous to the fuel atomization in a D.I. diesel engine. However, the diameter reduction is usually accompanied with decrease of spray tip penetration, thus worsening fuel spatial-distribution and fuel-air mixing. In this paper, a group-hole nozzle concept was proposed to solve the problem resulting from minimization of orifice diameter. Compared to the conventional multi-hole nozzle, group-hole nozzle has a series group of orifices, and each group consists of two micro-orifices with a small spatial interval and small angle. For examining the characteristics of the spray injected by the group-hole nozzle, the ultraviolet-visible laser absorption-scattering (LAS) imaging technique was adopted to determine vapor concentration and droplets density as well as other spray characteristics such as spray angle and penetration of both vapor and liquid phases.

A new technique was proposed for the simultaneous measurement of the concentration of fuel vapor and liquid in an evaporating diesel spray injected into a high temperature and high pressure environment. This technique was based on the principle of the absorption of ultraviolet laser light by fuel vapor and the scattering of visible laser light by fuel droplets in the diesel spray. For this principle, α-methylnaphthalene was used as a test fuel. Measuring the transmissivity of ultraviolet and visible laser lights absorbed and scattered by β-methylnaphthalene spray made it possible to analyze the fuel vapor concentration, droplets density and the mixture temperature in the diesel spray. A computerized tomographic transfer technique was also adopted to analyze three-dimensional fuel concentration distribution in the spray.

To get quantitative measurements of liquid and vapor phase concentration distributions in a gasoline spray, a laser-based absorption and scattering (LAS) technique was developed. The LAS technique adopts ultraviolet and visible lasers as light sources and a test fuel, which absorbs the ultraviolet light but does not absorb the visible light, instead of gasoline. The LAS principle is based on the incident light extinction in the ultraviolet band due to both vapor absorption and droplets scattering, whereas in the visible band, the incident light extinction is due only to the droplet scattering. The absorption spectra and molar absorption coefficients of the candidate test fuels including p-xylene, benzene and toluene, all of which have physical properties similar to gasoline, were investigated, and p-xylene was finally selected as a test fuel. Measurement accuracy of the LAS technique was discussed.

In order to measure the droplets and vapor concentration inside a fuel spray, a dual-wavelength laser absorption-scattering technique was developed using the second harmonic (532nm) and the fourth harmonic (266nm) of a Nd:YAG laser and using dimethylnaphthalene as the test fuel. The investigation results show that dimethylnaphthalene, which has physical properties similar to diesel fuel, is almost transparent to visible light near 532nm and is a strong absorber of ultraviolet light near 266nm. Based on this result, the vapor concentration in a fuel spray can be determined by the two separate measurements: a transmission measurement at a non-absorbing wavelength to detect the droplets optical thickness and a transmission measurement at an absorbing wavelength to detect the joint vapor and droplets optical thickness. The droplets density can be determined by extinction imaging through the transmission at the non-absorbing wavelength.

Quantitative imaging of the fuel concentration distribution was made in the combustion chamber of a propane-fueled spark ignition (SI) engine with the employment of laser-sheet-induced Rayleigh scattering technique for realizing the remote, nonintrusive and highly space- and time-resolved measurement. The original engine was modified to introduce YAG laser-induced sheet light into the combustion chamber and the scattered light was captured by a CCD camera fitted with a gated double-micro- channel plate image intensifier. The measurements were done at the crank angle of 270°ATDC in the combustion chamber of the engine motored at 200rpm with an air fuel ratio of 13 for various injection timing, injection direction and intake flow. The results show that with an appropriate matching of fuel injection timing, injection direction and intake flow, a stratified distribution of the fuel concentration can be realized.

The two-dimensional distributions of the liquid phase temperatures in diesel sprays injected into high-pressure and high-temperature environments were measured using the laser-induced fluorescence technique. The liquid fuel (n-hexadecane) was doped with pyrene(C16H10). The fuel spray doped with pyrene was injected under a high-pressure of 3.1MPa and a high-Temperature of 773K. The evaporating diesel spray was excited by laser radiation at 266nm, and the resulting fluorescence was imaged by an intensified CCD camera. The fluorescence intensity ratios of the pyrene monomer and excimer emissions have temperature dependence, and were used to determine the liquid phase temperatures in the diesel sprays. The cross-sectional distribution of the liquid phase temperature was estimated from the fluorescence images by the temperature dependence of the intensity ratio.

Planar laser-induced fluorescence (PLIF) technique was employed to perform the quantitative measurements of the cyclic variation of mixture concentration in the combustion chamber of a spark ignition (SI) engine. Nitrogen dioxide was used as the fluorescence tracer to simulate the fuel vapor. A Nd:YAG laser operated at its second harmonic wavelength was employed as the light source. The original engine was modified to introduce laser sheet light into the combustion chamber and the induced fluorescence was captured by a CCD camera fitted with a gated image intensifier. The measurements were done at the engine crank angles of 180° ∼ 300° ATDC with the engine speeds of 200 ∼ 400 rpm and the injection timings of -70 °, 50° and 100° ATDC. A theoretical analysis was made to describe the cyclically varying characteristics of the mixture concentration.

In order to investigate effects of the multi-hole nozzle with micro orifices on mixture formation processes in Direct-Injection Diesel engines, mixture characteristics were examined via an ultraviolet-visible laser absorption scattering (LAS) technique under various injectors. The injection quantity per orifice per cycle was reduced by nozzle hole sizes. The LAS technique can provide the quantitative and simultaneous measurements of liquid and vapor phases concentration distributions inside of the fuel spray. Mass of ambient gas entrained into the spray, liquid/ vapor mass and mean equivalence ratio of total fuel were obtained based on Lambert Beer's law. As a result, the leaner and more homogeneous fuel-gas mixture can be achieved by reducing the nozzle hole diameter, in the meanwhile more ambient gas were entrained into the spray. Moreover, relationships between mixture formation and D.I.

A comparison of spray characteristics was conducted between single- and multi-hole injectors. A commercial software (AVL FIRE) was used to investigate the internal flow inside the sac volume, as well as the initial spray behavior at 1 mm downstream of the nozzle exit. Microscopic imaging was applied to observe the spray dispersion angle (spray cone angle) at the vicinity of the nozzle. Laser absorption scattering (LAS) technique was implemented for measuring the mixture concentration. Three injection quantities, namely 0.5, 2.5, and 5.0 mg/hole, were selected to observe the differences between transient and quasi-steady spray. The vapor penetration at the initial stage of the injection was greater for single-hole than that of multi-hole injector due to faster fuel pressure build-up process inside the sac volume.

An early formation process of the spray, which was injected by a high-pressure swirl-type injector that is widely used in direct injection spark ignition (DISI) gasoline engines, was investigated through image analyzing techniques. The sprays were illuminated both by an Nd:YAG laser light sheet for getting the spray tomograms and by a tungsten lamp for getting the scattered back light shadow images of the sprays. The sprays were imaged by using a high-resolution CCD camera and a high-speed digital imaging system. The early development aspects of the spray were investigated in detail through the measurement of the tip penetration, cone angle and width of the early spray. At the start of injection, the liquid column emerges first, and it forms the “pre-swirl spray” without the swirl component. Following the liquid column, the liquid sheet emerges, however its radial velocity component is weak to form the complete hollow-cone spray. This spray changes into the “weak-swirl spray”.

The concept of two closely spaced micro-orifices (group hole nozzle) has been studied as a promising technology for the reduction of soot emission from direct injection (DI) diesel engines by improving the fuel atomization and evaporation. One of the main issues on group hole nozzle is the arrangement of orifices with various distances and angles. In this study, the ignition and combustion characteristics of wall-impinging diesel sprays from group-hole nozzles were investigated with various angles between two micro-orifices (included angles). A laser absorption scattering (LAS) technique for non-axisymmetric sprays, developed based on a LAS technique for axisymmetric spray, was applied to investigate the liquid/vapor mass distribution of wall-impinging sprays. The direct flame images and OH radical images inside a high pressure constant volume vessel were captured to analyze the effect of included angle on spray ignition and combustion characteristics.

With the aim of improving engine performance, recent trend of fuel injection nozzle design followed by engineers and researchers is focusing on more efficient fuel break up, atomization, and fuel evaporation. Therefore, it is crucial to characterize the effect of nozzle geometric design on fuel internal flow dynamics and the consequent fuel-air mixture properties. In this study, the internal flow and spray characteristics generated by the practical multi-hole (10 holes) nozzles with different nozzle hole length and hole diameter were investigated in conjunction with a series of computational and experimental methods. Specifically, the Computational Fluid Dynamics (CFD) commercial code was used to predict the internal flow variation inside different nozzle configurations, and the high-speed video observation method was applied to visualize the spray evolution processes under non-evaporating conditions.

The group-hole (GH) nozzle concept that uses two closely spaced micro-orifices to substitute the conventional single orifice has the potential to facilitate better fuel atomization and evaporation, consequently attenuate the soot emission formed in direct-injection (D.I.) diesel engines. Studies of quantitative mixture properties of the transient fuel spray injected by the group-hole nozzles were conducted in a constant volume chamber via the laser absorption-scattering (LAS) technique, in comparison with conventional single-hole nozzles. Specific areas investigated involved: the non-evaporating and the evaporating ambient conditions, the free spray and the spray impinging on a flat wall conditions. The particular emphasis was on the effect of one of key parameters, the interval between orifices, of the group-hole (SH) nozzle structure.

A comprehensive model for sprays emerging from high-pressure swirl injectors in DISI engines has been developed accounting for both primary and secondary atomization. The model considers the transient behavior of the pre-spray and the steady-state behavior of the main spray. The pre-spray modeling is based on an empirical solid cone approach with varying cone angle. The main spray modeling is based on the Liquid Instability Sheet Atomization (LISA) approach, which is extended here to include the effects of swirl. Mie Scattering, LIF, PIV and Laser Droplet Size Analyzer techniques have been used to produce a set of experimental data for model validation. Both qualitative comparisons of the evolution of the spray structure, as well as quantitative comparisons of spray tip penetration and droplet sizes have been made. It is concluded that the model compares favorably with data under atmospheric conditions.

In this study, air entrainment, fuel evaporation and mixing process of diesel sprays injected by micro-orifices for direct-injection diesel engines were investigated at the end of injection transient and after the end of injection. The mixture formation process was analyzed using a laser absorption scattering (LAS) technique, providing the information of quantified liquid and vapor mass concentration, entrained air concentration and equivalence ratio. The data was obtained at the timings of quasi-steady state, sudden velocity decrease, the end of injection and after the end of injection. Two micro-orifices, which have different orifice diameters, were selected as test nozzles to investigate the end-of-injection characteristics at different nozzle geometries. In case of smaller orifice diameter, the liquid phase regression was observed around the end of injection, while it was not observed at larger orifice diameter due to denser liquid concentration near the nozzle tip.