Search Results

As the cost and complexity of modern aircraft systems increases, emphasis has been placed on model-based design as a means for reducing development cost and optimizing performance. To facilitate this, an appropriate modeling environment is required that allows developers to rapidly explore a wider design space than can cost effectively be considered through hardware construction and testing. This wide design space can then yield solutions that are far more energy efficient than previous generation designs. In addition, non-intuitive cross-coupled subsystem behavior can also be explored to ensure integrated system stability prior to hardware fabrication and testing. In recent years, optimization of control strategies between coupled subsystems has necessitated the understanding of the integrated system dynamics.

The Air Force Research Laboratory Deployment and Sustainment Division (AFRL/HES), in coordination with Arthur D. Little, Inc., has undertaken a system-of-systems approach to defining and designing aerospace ground equipment (AGE). This method is usually used to take advantage of the open architecture nature of ne and developing electronics through modular design. This paper discusses how we applied it across the electronic, mechanical, and structural aspects of AGE to research and develop a new concept to meet the burgeoning needs of the 21st century Air Force.

As part of the DoD/NASA Lithium-Ion and More-Electric Aircraft (MEA) development programs, in-house life-testing and performance characterization of lithium-ion batteries of sizes 1-20 amp-hours (Ah) were performed. Using AC impedance spectroscopy, the impedance behavior of lithium-ion cells with respect to temperature, cycle number, electrode, and state-of-charge was determined. Cell impedance is dominated by the positive (cathode) electrode, increases linearly with cycle number, and exponentially increases with decreasing temperature. From cell performance testing, we have seen the cell behavior is extremely sensitive to the ambient temperature. Preliminary battery performance results as well as AC impedance and life cycle test results are presented below.

This paper describes the development, operation and testing of an across-gimbal ambient thermal transport system (GATTS) for carrying cryocooler waste heat across a 2-axis gimbal. The principal application for the system is space-based remote sensing spacecraft with gimbaled cryogenics optics and/or infrared sensors. GATTS uses loop heat pipe (LHP) technology with ammonia as the working fluid and small diameter stainless steel tubing to transport 100–275 W across a two-axis gimbal. The tubing is coiled around each gimbal axis to provide flexibility (less than 0.68 N-m [6 lbf-in] of tubing-induced torque per axis) and fatigue life. Stepper motors are implemented to conduct life cycling and to assess the impact of motion on thermal performance. An LHP conductance of approximately 7.5 W/C was demonstrated at 200 W, with and without gimbal motion. At the time this paper was written, the gimbal had successfully completed over 500,000 cycles of operation with no performance degradation.

As technology for both military and civilian aviation systems mature into a new era, techniques to test and evaluate these systems have become of great interest. To achieve a general understanding as well as save time and cost, the use of computer modeling and simulation for component, subsystem or integrated system testing has become a central part of technology development programs. However, the evolving complexity of the systems being modeled leads to a tremendous increase in the complexity of the developed models. To gain confidence in these models there is a need to evaluate the risk in using those models for decision making. Statistical model validation techniques are used to assess the risk of using a given model in decision making exercises. In this paper, we formulate a transient model validation challenge problem for an air cycle machine (ACM) and present a hardware test bench used to generate experimental data relevant to the model.

In this paper, a recently-developed algorithmic method of deriving the state equations of power systems containing power electronic components is described. Therein the system is described by the pertinent branch parameters and the circuit topology; however, unlike circuit-based algorithms, the difference equations are not implemented at the branch level. Instead, the composite system state equations are established. A demonstration of the computer implementation of this algorithm to model a variable-speed, constant-frequency aircraft generation system is described. Because of the large number of states and complexity of the system, particular attention is placed on the development of a model structure which provides optimal simulation efficiency.

Models for the components of a long-duration UAV power system are set forth. The models include the solar array, solar array power converter, fuel cell and electrolyzer system and corresponding power converter, and propulsion load. Based on these models, a power management control is derived, which when coupled with the component models, are used to simulate power system performance during start-up, through a day-night cycle, and through a solar eclipse.

This paper describes research to analyze widespread fatigue damage in lap joints. The particular objective is to determine when large numbers of small cracks could degrade the joint strength to an unacceptable level. A deterministic model is described to compute fatigue crack growth and residual strength of riveted panels that contain multiple cracks. Fatigue crack growth tests conducted to evaluate the predictive model are summarized, and indicate good agreement between experimental and numerical results. Monte Carlo simulations are then performed to determine the influence of statistical variability on various analysis parameters.

A highly modified F/A-18 aircraft is being used to demonstrate that aeroelastic wing twist can be used to roll a high performance aircraft. A production F/A-18A/B/C/D aircraft uses a combination of aileron deflection, differential horizontal tail deflection and differential leading edge flap deflection to roll the aircraft at various Mach numbers and altitudes. The Active Aeroelastic Wing program is demonstrating that aeroelastic wing twist can be used in lieu of the horizontal tail to provide autonomous roll control at high dynamic pressures. Aerodynamic and loads data have been gathered from the Phase I AAW flight test program. Now control laws have been developed to exploit aeroelastic wing twist and provide autonomous flight control of the AAW aircraft during Phase II. Wing control surfaces are being deflected in non-standard ways to create aeroelastic wing twist and develop the required rolling moments without use of the horizontal tail.

Typically, average-value models of power system components neglect harmonic information. Herein, a systematic method of including harmonic information in average-value models based on the theory of multiple reference frames is set forth. Computer simulation results show that when there is significant harmonic distortion of the ac distribution bus the models presented herein are more accurate than traditional average-value models. Furthermore, much of the computational advantage of average-value techniques over detailed modeling techniques is retained.

There has always been, from the very first UAV, a need for providing cost-effective methods of deploying unmanned aircraft systems at high altitudes. Missions for UAVs at high altitudes are used to conduct atmospheric research, perform global mapping missions, collect remote sensing data, and establish long range communications networks. The team of Gevers Aircraft, Technology Management Group, and Purdue University have designed an innovative balloon launched UAV for these near space applications. A UAV (Payload Return Vehicle) with a nested morphing wing was designed in order to meet the challenges of high altitude flight, and long range and endurance without the need for descent rate control with rockets or a feathering mode.

In long-duration, closed human habitats in space that include crop growth, one challenge that is faced while designing a candidate waste processor is the composition of solid-waste loads, which include human waste, packaging and food-processing materials, crop spoilage, and plant residues. In this work, a new modeling tool is developed to characterize crop residues and food wastes based on diet in order to support the design of solid-waste technologies for closed systems. The model predicts amounts of crop residues and food wastes due to food processing, crop harvests, and edible spoilage. To support the design of solid-waste technologies, the generation of crop residues and food wastes was characterized for a 600-day mission to Mars using integrated menu, crop, and waste models. The three sources of plant residues and food waste are identified to be food processors, crop harvests, and edible spoilage.

Due to the instabilities that may occur in power systems with regulated loads such as those used in military aircraft, ships, and terrestrial vehicles, many analysis techniques and design methodologies have been developed to ensure stable operation for expected operating conditions. However, many of these techniques are difficult to apply to complex systems and do not guarantee large-displacement stability following major disturbances such as faults, regenerative operation, large pulsed loads, and/or the loss of generating capacity. In this paper, a design paradigm is set forth guaranteeing large-displacement stability of a power system containing a significant penetration of regulated (constant-power) loads for any value of load power up to and including the steady-state rating of the source. Initial investigations are performed using an idealized model of a dc-source to determine the minimum requirements that ensure large-displacement stability.

Modern military engines desire both the fuel efficiency of high-bypass turbofans and the high specific thrust of a low-bypass turbofan. Using traditional engine architectures, performance and efficiency are in conflict, so an engine is usually designed to best meet requirements for its primary mission. While the concept of a variable cycle engine is not new, recent advances in engine architecture technology suggest that adding a second bypass stream to a traditional turbofan can provide significant benefits. This “third stream” (the core flow being the primary stream and the inner bypass being the second stream) airflow can be independently modulated so that engine airflow demand can be matched with the available inlet flow at a variety of operating points, thereby reducing spillage drag. Additionally, the third stream air provides a valuable heat sink for cooling turbine cooling air or dissipating other aircraft heat loads.

The NASA Specialized Center of Research and Training in Advanced Life Support (ALS/NSCORT) Education and Outreach Program is designed to engage audiences through concepts and technologies highlighted in the NSCORT research program. The outreach program is composed of three thrust areas. These areas are technical outreach (graduate education, technology transfer, presentations to industry, etc.), educational outreach (professional development, undergraduate, K-12), and public outreach (museums, state fairs, etc.) Program design of the technical and educational outreach began in January 2003. This paper reports anecdotal data on one ALS/NSCORT outreach program and gives a brief description of the other programs in their pilot stages. Technical and educational outreach programs developed to date include: 1) Summer Fellowship Research Program, 2) Distance Learning Course, 3) Key Learning Community Collaborative Project and 4) Mission to Mars.

Two compact intercoolers are designed for the Rotax 914 aircraft engine to increase engine power and avoid engine knock. A study is performed to investigate the effects of unsteady airflow on intercooler performance. Both intercoolers use air-to-liquid cross flow heat exchangers with staggered fins. The intercoolers are first tested by connecting the four air outlets of the intercooler to a common restricted exit creating a constant back pressure which allows for steady airflow. The intercoolers are then tested by connecting the four air outlets to a 2.4 liter, 4 cylinder engine head and varying the engine speed from 6000 to 1200 RPM corresponding to decreasing flow steadiness. The test is performed under average flight conditions with air entering the intercooler at 180°F and about 5 psig. Results from the experiment indicate that airflow unsteadiness has a significant effect on the intercooler's performance.

As aircraft continue to increase their power and thermal demands, transient operation of the power and propulsion subsystems can no longer be neglected at the aircraft system level. The performance of the whole aircraft must be considered by examining the dynamic interactions between the power, propulsion, and airframe subsystems. Larger loading demands placed on the power and propulsion subsystems result in thrust, speed, and altitude transients that affect the aircraft performance and capability. This results in different operating and control parameters for the engine that can be properly captured only in an integrated system-level test. While it is possible to capture the dynamic interactions between these aircraft subsystems by using simulations alone, the complexity of the resulting system model has a high computational cost.

Wheat is a candidate crop for the Advanced Life Support (ALS) system, and cereal grains and their products will be included on long-term space missions beyond low earth orbit. While the exact supply scenario has yet to be determined, some type of post-processing of these grains must occur if they are shipped as bulk ingredients or grown on site for use in foods. Understanding the requirements for processing grains in space is essential for incorporating the process into the ALS food system. The ESM metric developed by NASA describes and compares individual system impact on a closed system in terms of a single parameter, mass. The objective of this study was to compare the impact of grain mill type on the ESM of producing yeast and flat breads. Hard red spring wheat berries were ground using a Brabender Quadrumat Jr. or the Kitchen-Aid grain mill attachment (both are proposed post-harvest technologies for the ALS system) to produce white and whole wheat flour, respectively.

In this research, excitation strategies for a salient-pole wound rotor synchronous machine are explored using a magnetic equivalent circuit model that includes core loss. It is shown that the excitation obtained is considerably different than would be obtained using traditional qd-based models. However, through evaluation of the resulting ‘optimal’ excitation, a relatively straightforward field-oriented type control is developed that is consistent with a desire for efficiency yet control simplicity. Validation is achieved through hardware experiment. The usefulness/applicability of the simplified control to variable speed applications is then considered.

Rotating Heat Pipe (RHP) technolog y is being developed for high speed (>20 krpm) regimes of electric motor/generator cooling. The motivation for this research is the potential application of the high speed RHPs for the thermal management of advanced rotating electrical machines. The passive nature and relatively simple features of this device are attractive for the removal of waste heat from the rotors of electric machines. Interesting air-cooling experimental results of two high speed RHPs designed, fabricated and tested at AFRL are presented here. Emphasis is made on external heat removal concepts useful for cooling the RHP condenser in order to be successful in promoting this technology to real world problems.