Search Results

We have developed an electric rear-drive unit to enable all-wheel drive (AWD) applications to the compact FF hybrid passenger vehicles. The development is intended to provide a compact and low cost unit with low fuel consumption. The unit newly introduces a two-axis gear train that enables a compact design, an induction motor and an ATF (automatic transmission fluid) stirring resistance restraining structure that contribute to lower fuel consumption. This paper presents the features and performance of the electric rear-drive unit.

Recently, for the protection of the environment, the regulation of automobile fuel consumption and exhaust gas emission has been strengthened. To improve fuel economy, it is demanded that each engine part contributes to reducing the workload of the engine, even the engine lubrication oil pump. In response to this, a new variable discharge oil pump was developed. It is the world's first internal gear type oil pump that has electronically controlled continuously variable discharge. The work performed by the pump chiefly takes two forms: sliding friction of the rotor and pumping work which moves the oil. First, in developing a variable discharge oil pump, a new tooth profile of the rotor was developed to reduce its sliding friction. As a result, the sliding friction of the rotor was reduced by 34% while maintaining the same theoretical oil discharge rate. Next, a variable discharge mechanism using an internal gear was developed.

Over the past decades, the automotive industry has made significant efforts to improve engine fuel economy by reducing mechanical friction. Reducing friction under cold conditions is becoming more important in hybrid vehicle (HV) and plug-in hybrid vehicle (PHV) systems due to the lower oil temperatures of these systems, which results in higher friction loss. To help resolve this issue, a new internal gear fully variable discharge oil pump (F-VDOP) was developed. This new oil pump can control the oil pressure freely over a temperature range from -10°C to hot conditions. At 20°C, this pump lowers the minimum main gallery pressure to 100 kPa, thereby achieving a friction reduction effect of 1.4 Nm. The developed oil pump achieves a pressure response time constant of 0.17 seconds when changing the oil pressure from 120 kPa to 200 kPa at a temperature of 20°C and an engine speed of 1,600 rpm.

One of the problems concerning T/M is conventionally how “Improving the input torque as the engine gets higher power” and “Making product lighter in weight and more compact to improve the fuel consumption” can be realized at the same time. To realize these things at the same time, it is needless to say that the gears must be stronger. For the “pitting fatigue strength” which is quoted as a problem lately, the fatigue mechanism has not been clarified, yet. Therefore, it is now a big problem how to achieve high strength. In the meantime, we tried to develop the production engineering for “finer crystal grains” and “fine-dispersion precipitation of carbo-nitrides,” and succeeded in improving “pitting fatigue strength” remarkably. Such results will be reported in the following sections:

Electrification of the powertrain to improve vehicle fuel economy is a key technology to achieve strict fuel economy legislation. However, only limited numbers of small class vehicles such as a B segment adopt electric powertrain. This is presumed that cost effectiveness for fuel economy is small and mounting space for additional powertrain is limited. In this paper, the optimum solution of a strong hybrid system suitable for the small vehicles was studied. First, from the viewpoint of maximization of energy efficiency, we compared contributions of engine efficiency and transmission efficiency during mode cycle driving and selected automated manual transmission as a suitable transmission for small vehicles. In comparing the hybrid system function, we determined a motor generator connecting shaft and a necessary motor generator output power for attaining both fuel economy and drivability.

AISIN SEIKI CO., Ltd. Started the production of electronically controlled hydraulic automatic transmissions for medium-duty trucks and buses in 1989. The number of vehicles on the Japanese market in which this system is adopted is increasing steadily. After re-examining market needs, AISIN SEIKI CO., Ltd. has newly developed an electronically controlled hydraulic automatic transmission A580 which focuses on improved input capacity, driving performance and fuel economy for medium-duty trucks and buses and lessens learnt from experience.

Rear steering system can improve vehicle stability using active control of the rear wheel angles. For designing the rear steering system, environmental conditions, performance deterioration due to aging and component variation as a result of manufacturing tolerance under mass production must be taken into consideration. We have applied two-degree-of-freedom (2DOF) feedback control with feedforward control for the motor servo control so that the rear steering actuator can track the target rear steering angle accurately and stably. The control system is designed based upon a nominal mathematical model and its variation range. As a result, the rear steering actuator can be controlled with excellent performance and high reliability. This paper describes the mathematical model construction in the frequency domain and a robust motor servo controller design based on 2DOF feedback control with feedforward control.

As a process that enables the high-speed and continuous forming of lengthy materials with a constant cross-sectional configuration, roll forming offers much higher productivity than the stamping process. However, in case a change must be made to the shape of the cross section, the material must normally be stamped or joined with a part containing a separate shape. This affects productivity, increases the number of pieces, and degrades the material's appearance. This report describes the roll-forming technology that we developed, in which the cross section of the material can be changed gradually. This method adopts a system which uses a movable and rotatable roll-stand that enables high-speed, continuous roll-forming processes.

The conventional hydraulic valve lifters, which eliminate the valve clearance adjustment, normally use the pressurized engine lubricant for the working fluid. We have developed a quite new type lifter, named “self-contained hydraulic valve lifter”, which possesses the working fluid in itself. Because the new type lifter is independent of the pressurized engine lubricant, it has some advantages, especially that it can be applied to the existing engine using the mechanical valve gear without almost any engine modifications. And we have confirmed that the self-contained hydraulic valve lifter has good characteristics and reliability and have applied it to the mass production engine (i.e. Toyota 1.3L gasoline engine) for the first time in the world. This paper describes the construction, the characteristics and the reliability of this lifter.

There are such outside door handles called smart handles which have a transmitting antenna, a lock/unlock sensor, and a sensor detection circuit, with which operation of door lock is possible just by "touching" the electrostatic-capacitance type sensor of the handles.As the design of the outside handles, body color painting and Cr plating are adopted. However, if plating is applied over the entire surface of a smart handle, electromagnetic waves transmitted from the antenna will be blocked since plating material is electrically conductive. In addition to this, touching a part other than the sensor may change the electrostatic-capacitance of the sensor, which results in unwanted functioning of the lock/unlock sensor. Because of this, only part of the handle, which does not hinder the transmission of electromagnetic waves and does not cause unwanted functioning, is covered by plating, that is called, "Partially plated specifications" (Figure 1).

Automating the inspection of the piston combustion chamber volume is difficult and prevents establishing an unmanned machining process of the piston in the future. So, we developed an inspection technique which uses a Range Finder, non-contact visual sensor, and calculate the chamber volume by integrating 3D position data. We applied this real-time measurement technique which enables 100 % inspection to our production lines. Then, we developed the “Defect Free Production Line”, which calibrates itself by feeding back the measured volume data to the machining process. Our paper will explain this inspection technique and our “Defect Free Production Line”.

Responsiveness is one of the main characteristics of a brake booster. The design of a tandem booster, with its two boosting chambers, has a negative influence on high responsiveness. This report, using the CFD method for the air flow analysis, shows the way we found the most suitable air passage within the space of the given design of the current production tandem booster.

Recently, for the aspects of ecology and economy, fuel efficiency improvement demand has been increased globally. And, various types of hybrid systems have been suggested. In response to this market demand, AISIN SEIKI has been developing Synchronizer-less hybrid automated manual transmission (HV-AMT) system aiming excellent transmission efficiency, excellent agility, and shift change quality like a step automatic transmission (AT). This hybrid system is constructed based upon a parallel 2-axis manual transmission (MT) which originally has high transmission efficiency. The synchronizer system of a MT is replaced by a Dog clutch system which does not spoil the transmission efficiency and never makes failure in synchronization. This Dog clutch system includes a modified detent function, a shift actuator of linear motor, advanced function controls for a clutch and a shift actuator.

As a part of our process engineering (planning) steps and in order to shorten the initial flow control after the implementation of a production system, we have been adopting countermeasures for defects that have been forecasted by the application of FMEA. However, due to this having to be done with limited information (which is dependent upon the skill level of the operator) and due to the fact that the effects of each particular countermeasure are not fully understood, we cannot be certain that the measures implemented during the planning stages are thorough enough. The current situation is that countermeasures for most issues are being handled during the initial flow control stages based on the trial-and-error method. Given this situation, normally, it would take us more than three months from the time of line-off (start of production) to achieve our target rate of capacity utilization.

We developed a hydrogen-added after-burner system for a new catalyst heating system, which realized large reduction of emissions during start-up at low temperatures when Hydro-Carbon (HC) emission was rather high. Key development items of this system are a water electrolysis type small size on-bord hydrogen supply unit and engine matching technique for the verification of emission reduction effects.

Recently, for protection of the environment, the regulation of automobile fuel consumption and exhaust gas emission has been strengthened. In light of such circumstances, automobile parts are generally required to be able to improve fuel efficiency and reduce exhaust gas emission. In order to meet such requirements, the structure of fuel/exhaust-related devices has become complicated. Redesigns of future products that will be increasingly complex will lengthen the development period and reduce cost efficiency seriously.

Aiming at improved reliability and cost reduction of position sensors for automobiles, we tackled with the challenge of developing long life contact type potentiometer which has a simple construction and cost advantage. We made clear the wear characteristics of the resistor materials and the mechanism how noise occurs, and developed a long life, low noise resistor material, and the double - layer resistor structure which has excellent characteristic in durability. We also clarified the ways of using brushes according to applications through the investigation of the relationship between the contact shape and the amount of wear of the resistor. Based on these investigation, we have developed a highly reliable throttle position sensor and a long life vehicle height sensor.