Search Results

Active control mainly comprises of three parts; sensor-detects the input disturbance, actuator -provide counter measures and control logic -processing of input disturbances and converting it into logical output. Lot of methods for active vibration control are available but this paper deals with active control of steering wheel vibrations of an LCV. A steering wheel is, one such component that directly transfers vibration to the driver. Active technique described here is implemented using accelerometer sensor, IMA (Inertial Mass Actuator) and feed forward Fx-LMS (Filtered reference Least Mean Square) control algorithm. IMA is a single-degree-of-freedom oscillator. To enable a control, IMA needs to be coupled to the structure at a single point, acting as an add-on to the passive system. Fx-LMS is a type of adaptive algorithm which is computationally simple and it also includes compensation for secondary path effects by using an estimate of the secondary path.

In order to travel in a chaotic and dynamic environment, an autonomous vehicle requires a motion plan. This motion plan ensures collision free, optimum travel without violating any traffic rules. The optimum solution for path planning problem exists in higher dimensions, however, with the help of useful heuristics the problem can be solved in real time, which is required for real time operation of an autonomous vehicle. There are different well established techniques available to plan a collision free kinematically traversable path. One of such techniques is called conformal Lattice planner. However, the legacy version of conformal lattice planner is not optimized and also is prone to fail under specific dynamic environment conditions. Moreover, the legacy version of conformal lattice planner is also not road aware. Due to this reason it is a semi optimized way to solve the motion planning problem.

Two carburetted passenger cars of different makes, converted for CNG (Compressed Natural Gas) operation (in dual mode) and optimised by ARAI (The Automotive Research Association of India, Pune, India), were tested for vehicular performance. The respective engines were also mapped for performance, energy consumption and emission. The power loss in CNG mode was 7% & 15% and torque reduction was 21% & 15% in respective engines. There is considerable improvement in thermal efficiency and reduction of emission in the entire operating range. The vehicle performance on Chassis Dynamometer shows similar results. The second engine was also tested with a ceramic catalytic converter which gave 93% reduction in CO and 50% reduction in HC in major portion of operating range. 1100 CC car was also tested on the test track. Optimisation work included installation of ARAI mixer design.

Electric passenger car with floor battery usually have its front boot space empty and the space is used as additional luggage storage. This space can be utilized to capture the wind energy and generate electricity. Based on this, the objective of this work is to perform an aerodynamic analysis of an electric passenger car using wind turbine placed at the front. Initially the aerodynamic analysis of a basic electric car model is performed and further simulated using wind turbines and aerodynamic add-on-devices. The simulation is carried-out using ANSYS Fluent tool. Based on the simulation result, scaled down optimized model is fabricated and tested in wind tunnel for validation. The result shows reduction of drag coefficient by 5.9%.

Any change is vehicle exterior design, affects the aerodynamics characteristic. Generally different types of roof racks are attached on passenger vehicles to carry luggage which affects aerodynamic drag. The objective of this work is to perform aerodynamic analysis of ground vehicle with roof rack to investigate the change in drag coefficient. First, the aerodynamic analysis of a baseline passenger car model is performed with and without generic benchmarked roof rack at 100 kmph. Further analysis is carried out with different new designs of roof racks. Based on simulation result, a scaled down prototype model is fabricated and validated by using a wind tunnel test for optimum suitable case. The modelling of the vehicle is done in CATIA tool and simulation is carried out by using ANSYS Fluent.

In high speed race cars, aerodynamics is an important aspect for determining performance and stability of vehicle. It is mainly influenced by front and rear wings. Active aerodynamics consist of any type of movable wing element that change their position based on operating conditions of the vehicle to have better performance and handling. In this work, front and rear wings are designed for race car prototype of race car. The high down force aerofoil profiles have been used for design of front and rear wing. The first aerodynamic analysis has been performed on baseline model without wings using CFD tool. For investigation, parameters considered are angle of attack in the range of 0-18° for front as well as rear wing at different test speeds of 60, 80, 100 and 120 kmph. The simulation is carried out by using ANSYS Fluent. The simulation results show significant improvement in vehicle performance and handling parameters.

Active aerodynamics can be defined as the concept of reducing drag by making real-time changes to certain devices such that it modifies the airflow around a vehicle. Using such devices also have the added advantages of improving ergonomics and performance along with aesthetics. A significant reduction in fuel consumption can also be seen when using such devices. The objective of this work is to reduce drag acting on a passenger car using the concept of active aerodynamics with grill shutters and air dams. First, analysis has been carried out on a baseline passenger car and further simulated using active grill shutters and air dams for vehicle speed ranging from 60 kmph to 120 kmph, with each active device open from 0° to 90°. The optimized model is then validated for a scaled down prototype in a wind tunnel at 80kmph. Vehicle has been modelled using SolidWorks tool and the simulation has been carried out using ANSYS Fluent.

Major cause of air pollution in the world is due to burning of fossil fuels for transport application; around 23% GHG emissions are produced due to transport sector. Likewise, the major cause of air pollution in Indian cities is also due to transport sector. Marginal improvement in the fuel economy provide profound impact on surrounding air quality and lightweighting of vehicle mass is the key factor in improving fuel economy. The paper describes robust and integrated approach used for design and development of lightweight bus structures for Indian city bus applications. An attempt is made to demonstrate the use of environment friendly material like aluminium in development of lightweight superstrutured city buses for India. Exercise involved design, development and prototype manufacturing of 12m Low Entry and 12m Semi Low Floor (SLF) bus models.

Forging is a metal forming process involving shaping of metal by the application of compressive forces using hammer or press. Forging load of equipment is an important function of forging process and the prediction of the same is essential for selection of appropriate equipment. In this study a hot forging material i.e. 42CrMo4 steel is selected which is used in automotive components like axle, crank shaft. Hot forging experiments at 750°C are carried out on cylindrical specimens of aspect ratio 0.75 and 1.5 with true height strain (ln (ho/hf)) of 0.6. Forging load for the experiments is calculated using slab and upper bound deformation models as well as Metal forming simulation using commercially available FEA software. The upper bound models with 30% deviation from the simulation results are found to be more accurate compared to the slab models.

Due to the transformation of the automotive industry from conventional vehicles to electric vehicles, new challenges have emerged concerning Electromagnetic Compatibility. Though the Radiated Emission limits in global regulation are the same for both types of powertrains of vehicles, however, due to the phenomena of conversion of high voltage to low voltage, rapid charging/discharging, and different components involved in electric powertrain, the Radiated Emission from electric vehicles give a strikingly different trend which is challenging to combat. When compared with the conventional Spark Ignition vehicle, many other electronic components of the electric vehicle stay in the mode of Power ON while in the “Ignition ON” steady state. This resulted in us observing a significant shift in the amplitude and frequency throughout the frequency band of Radiated Emission measurement.

The death toll due to traffic accidents in India is on a rise, according to the latest Road Transport ministry report, a total of 4.97 lakh road accident was reported in 2011. Though compared to 2010, the accidents have gone down by 1,945, the number of deaths at 1,42,485 has increased by over 7,000.[1] This paper proposes a design of an Emergency Intimation System (EIS) tailored to fit for Indian consumer needs and available infrastructure. EIS is an emergency alert technology devised to assist drivers and passenger in an event of vehicle crash. Majority of deaths are caused by slow accident response time. EIS is aimed to lower this response time and ensure that the required rescue and medical services are made available in time. This device employed to make this emergency alerts will be fitted into the vehicle Electrical and Electronics (E/E) architecture and will have interfaces with crash sensor network, CAN network and GSM etc.

In year 2015, 17 people were killed every hour by road accidents in India [1]. The occurrence of road accidents is observed to be higher during night, when visibility is at its lowest. The two factors which affect visibility are insufficient illumination and glare caused by the oncoming traffic. The Adaptive Front Lighting System [AFS] is an active safety feature which addresses these problems by employing specific lighting modes for Town, Country, Expressway conditions and automatic switching between Driving Beam and Passing Beam whenever required. Matrix of LEDs or a Projector with an actuator or a combination of both is employed in achieving different Lighting modes. The projector based AFS module is preferred for implementing the AFS control logic for passing beam owing to its economic cost.

The Light commercial vehicle (LCV) is primarily used for the last mile delivery and it hold the volume share of around 61% in the commercial vehicle segment. The last mile delivery services have seen a massive surge after the CoVID 19 pandemic resulting is the increase sale of LCV in last few years and is expected to grow further by 8-11% in the coming years. However, city logistic is also responsible for most pollution and noise in the city. Hence, policymakers are aiming to reduce carbon footprint by promoting the use of Electric vehicle by providing incentive to automakers though schemes like FAME I and FAME II. In order to effectively reduce the carbon footprint within city it is important to increase the use of new electric vehicle and convert the old polluting vehicles to electric. Hence, a retro fitment solution for converting used LCV to electric can help in reducing emission as well as noise pollution. Later the same solution can be offered as OE fitment solution.

The Exhaust Noise is one of the major noise pollutants. It is well-known that for higher noise reduction, the engine has to bear high back pressure. For a race car, back-pressure plays a major role in engine's performance characteristics. For a given condition of engine rpm & load, conventional muffler has a fixed value of back-pressure and noise attenuation. Better acceleration requires low back-pressure, but the exhaust noise should also be less than the required (Norm) value (110 dBA). This contradicting condition is achieved here by using a ‘Butterfly Valve’ in this novel exhaust muffler. The butterfly valve assumes 2 positions i.e. fully open & fully closed. When the valve is fully closed, the noise reduction will be higher, but the back-pressure will also shoot up. When open, noise reduction will be less and so the back-pressure. So, when better performance is required, the valve is opened and back-pressure is reduced. The muffler is designed for a 4 cylinder 600 cc engine.

In today’s scenario, the emission norms are getting stringent day by day due to an increased level of pollution. The world is shifting towards low carbon footprint which made it necessary to adopt efficient technologies with fewer emissions. The hybridization of vehicles has resulted in improved efficiency with lower emissions which can fulfil the near future emission norms. Retrofitting of hybrid components into a conventional IC engine vehicle is so far the best way to achieve better performance both economically and technologically. This research is primarily focused on the design and development of a novel retrofit solution of P3x architecture for the light commercial vehicle. This retrofit solution is different from other hybrid solutions in terms of powertrain. It contains an innovative add-on powertrain along with the existing powertrain. This additional powertrain consists of a pair of helical gears followed by a chain and sprocket as a coupler for traction motor.

Frontal crash is the most common type of accidents in passenger vehicles which results in severe injuries or fatalities. During frontal crash, some frontal vehicle body has plastic deformation and absorbs impact energy. Hence vehicle crashworthiness is important consideration for safety aspect. The crash box is one of the most important parts in vehicle frontal structure assembly which absorb crash energy during impact. In case of frontal crash accident, crash box is expected to be collapsed by absorbing crash energy prior to the other parts so that the damage to the main cabin frame and occupant injury can be minimized. The main objective of this work is to design and optimize the crash box of passenger vehicle to enhance energy absorption. The modeling of the crash box is done in CATIA V5 and simulations are carried out by using ANSYS. The results show significant improvement in the energy absorption with new design of the crash box and it is validated experimentally on UTM.

One of the primary reasons for road accidents is driving while distracted or drowsy. Often, long and monotonous road journeys lead to distracted or drowsy driving. Therefore, there is a need for a system which alerts a distracted or drowsy driver. Moreover, as the levels of autonomy move beyond SAE Level 2, the system assumes a larger share of the dynamic driving task. Under challenging circumstances, the system might ask the driver to take back vehicle control. To guarantee safety, it’s crucial to monitor the driver’s condition in order to assess their readiness to regain control of the vehicle. An advanced safety feature known as a driver monitoring system (DMS), sometimes referred to as a driver state sensing (DSS) system, is designed to monitor a driver’s attentiveness and alertness, providing warnings or alerts to refocus their attention on driving when drowsiness or distraction is detected.

The use of Hybrid Electric Vehicles (HEV) will become imperative to meet the emission challenges. HEV have two power sources-fossil fuels driven I.C. Engine and the battery based drive. Battery technologies have seen a tremendous development, and therefore HEV’s have been benefited. Even as the battery capacities have improved, maintaining and monitoring their health has been a challenge. This research paper uses open-source platform to build a BMS. The flexibility in the implementation of the system has helped in the rapid prototyping of the system. The BMS system was evaluated on a scaled-down electric toy car for its performance and sustainability. The BMS was evaluated for reverse polarity, protection against overcharge, short-circuit, deep discharge and overload on lead acid battery. It also includes temperature monitoring of the batteries. This proposed system is evaluated on the in-house HEV two-wheeler. The initial results are promising.

Ride is considered to be one of the crucial criterion for evaluating the performance of a vehicle. Automobile industry is striving for improvement in designs to provide superior passenger comfort in Commercial vehicles segment. In Industry, Quarter-car model has been used for years to study the vehicle’s ride dynamics. But due to lower DOF involved in quarter car, the output accuracy is somewhat compromised. This paper aims in development of a 7 DOF full-car Model to perform the ride- comfort analysis for Light Duty 4*2 Commercial Bus using MATLAB Simulink which can be used to tune the suspension design to meet the required ride-comfort criteria. Firstly, experimental data and Physical Parameters are collected by performing Practical Test on commercial Bus on different road profiles. Secondly, a Full Car Mathematical Model with 7 DOF has been developed for a bus using MATLAB Simulink R2018a.

Wheel rims and wheel hub bearings are critical components of Heavy Commercial Vehicle (HCV) suspension systems and are subjected to extensive fatigue loading throughout their operational life. Actual loading conditions on wheels are a combination of radial loads (vertical loads) and cornering loads (lateral loads) acting simultaneously and are directly influenced by payload and road conditions. Currently for Indian usage, there are test guidelines [1] only for separate uniaxial Radial Fatigue Test (RFT) and Cornering Fatigue Test (CFT) for wheel rims which might not represent realistic combined loading conditions, and no generic guidelines are available for testing of wheel hub bearings.