Search Results

The measurement of the instantaneous flame temperature and soot concentration in the combustion chamber of a running diesel engine can provide useful information relating to the formation of two important exhaust pollutants, NOx and particulates. The two-colour method is based on optical pyrometry and it can provide estimates of the instantaneous flame temperature and soot concentration. The theoretical basis of the method is outlined in a companion paper. This paper deals with the practical problems involved in the construction of a working system, including suitable calibration techniques. The accuracy of the measurements of flame temperature and soot concentration is also discussed using results from a various sources.

The two-colour method is based on optical pyrometry and can readily be implemented at a modest cost for the measurement of the instantaneous flame temperature and soot concentration in the cylinders of diesel engines. With appropriate modification, this method can be applied to other continuous and intermittent combustion systems, such as those for gas turbine and boiler burners. This paper outlines the theoretical basis of the method, with particular attention being paid to the assumptions relating to the evaluation of the flame temperature and soot concentration. A companion paper deals with the practical problems involved in constructing a working system, including suitable calibration techniques, and assessment of the method accuracy.

Diesel Exhaust Fluid (DEF) systems are required to function in cold ambient temperatures below the freezing point of DEF. Manufacturers may demonstrate compliance by following an EPA guidance procedure described below [2], using whole vehicles at winter test sites at −18 deg C or lower. However, commercial trucks may have multiple variants with different DEF system layouts, so it is impractical to test every possible configuration. A climatic chassis dynamometer (CCD) can also be used for this test, but this is still expensive and time consuming, and does not address the problem of complexity. Instead, much time and expense can be saved by using simulation methods to identify worst case configurations, and to demonstrate with confidence that a limited number of tests will cover the whole possible range. This methodology can further be used to show that a range of vehicles can be represented with selected rig tests in a cold chamber.

Our earlier experimental study has shown that exhaust unburnt hydrocarbon emissions from spark-ignition engines can be reduced effectively by using in-cylinder catalysts on the surface of the piston top-land crevice. In order to improve the understanding of the process and mechanism by means of which unburnt hydrocarbon emissions are reduced, a phenomenological mathematical model was developed for catalytic oxidation processes in the piston-ring-pack crevice. This paper describes in details the modelling of the processes of the gas flow, mass diffusion and reaction kinetics in the crevices. The flow in the crevices is assumed to be isothermal and at the temperature of the piston crown surface. The overall rate of reaction is calculated using expressions for mass diffusion for laminar flows in channels and a first-order Arrhenius-type expression for catalytic reaction kinetics of hydrocarbon oxidation over platinum.

A mathematical model has been developed which describes the evaporation and trajectories of fuel droplets during their flight in the inlet manifold of port-injected gasoline engines. Based on the model, a computer simulation program was developed, and sample results of this program are given in this paper. Extensive results obtained using the simulation program are described in a companion paper. The simulation program can be used as a tool to improve understanding of mixture preparation in port injected engines. Such effects as: engine load and speed, air and fuel temperature, fuel type, fuel injection velocity, injection timing, and spray droplet size can be investigated.

Turbulent Jet Ignition is an advanced spark initiated pre-chamber combustion system for otherwise standard spark ignition engines. Combustion in the main chamber is initiated by jets of partially combusted (reacting) pre-chamber products which provide a high energy ignition source. The resultant widely distributed ignition sites allow relatively small flame travel distances enabling short combustion durations and high burn rates. This presentation outlines development of this combustion concept in a modern normally aspirated PFI production engine. Experimental results have highlighted high thermal efficiency (42.8%), significant fuel economy improvement (>20%), low engine out NOx (<10 ppm), knock limit extension, high load capability (>13 bar IMEPn) and high speed operation (5500 rev/min). Presenter William P Attard, MAHLE Powertrain LLC

The 2025 Corporate Average Fleet Economy (CAFE) fuel economy regulations are a significant challenge to the automotive industry. These regulations require dramatic increases in vehicle fleet fuel economy. This paper will identify and analyze a portfolio of technologies that have the potential to achieve the 2025 CAFE fuel economy targets, focusing on powertrain enhancements. The study uses a MAHLE Powertrain developed fleet modeling tool and a range of vehicle technologies and powertrain data taken from MAHLE's global research and development activities. Powertrain technologies considered include extreme engine downsizing, dilute combustion, friction reduction, hybridization, diesel and alternative fuels. The vehicle technologies analyzed include vehicle light weighting, reduced rolling resistance, advanced transmissions and improved aerodynamics.

The work was concerned with experimental study of the turbulent flame development process of ethanol fuels in an optically accessed spark ignition research engine. The fuels were evaluated in a single cylinder engine equipped with full-bore overhead optical access and operated at typical stoichiometric part-load conditions. High-speed natural light (or chemiluminescence) imaging and simultaneous in-cylinder pressure data measurement and analysis were used to understand the fundamental influence of both low and high ethanol content on turbulent flame propagation and subsequent mass burning. Causes for the difference in cyclic variations were evaluated in detail, with comparisons made to existing burning velocity correlations where available.

Heavy duty hydrogen (H2) internal combustion engines (ICEs), typically conversions from base diesel engines, can experience significant deterioration of combustion efficiency with enleanment despite relative engine stability due in part to non-optimized combustion chamber geometry for spark ignited (SI) combustion. This causes un-combusted H2 to “slip” into the exhaust largely undetected since it is not a typically measured exhaust species. In this study, several implications of H2 slip in H2 ICEs are explored. The sensitivity of air fuel ratio (AFR) measurement to H2 slip is discussed. The challenge this poses for closed-loop transient controls and the impact on nitrogen oxides (NOx) emissions are also shown. Finally, test results from an H2 ICE using an active pre-chamber highlight the improvement in combustion efficiency and transient stability relative to a baseline SI engine.

Current market demands in conjunction with increasingly stringent emission legislation have vehicle manufactures striving to improve fuel economy and reduce CO2 emissions. One way to meet these demands is through engine downsizing. Engine downsizing allows for reduced pumping and frictional losses. To maintain acceptable drivability and further increase efficiency, power density increase through the addition of boosting is employed. Furthermore, efficiencies have been realized through the use of high gear count transmissions, providing an opportunity for manufactures to effectively down speed the engine whilst still achieving the desired drivability characteristics. As a result of these efficiency improvements, gasoline turbo charged direct injected (GTDI) engines are developed for and tend to operate in low engine speed, high torque conditions .

The paper first describes three linked computational models which allow the estimation of: swirl generated during the induction process; the modification of swirl with bowl-in-piston combustion chambers during compression as the piston approaches top dead centre; the interaction of the fuel sprays with swirl including relative crosswind velocities between the air and the fuel sprays and spray impingement velocities. The paper then presents experimental results from a single-cylinder direct injection diesel engine, during which both the fuel spray and swirl parameters were changed systematically. Finally, the predicted spray impingement and crosswind velocities for this engine are correlated with the engine performance obtained experimentally, in particular, with fuel economy and smoke emission.

Tumble and swirl motions in the cylinder of a four-valve SI engine with production type cylinder head were investigated using a cross-correlation digital Particle Image Velocimetry (PIV). Tumble motion was measured on the vertical symmetric plane of the combustion chamber. Swirl motion was measured on a plane parallel to the piston crown with one of intake ports blocked. Large-scale flow behaviours and their cyclic variations were analysed from the measured two-dimensional velocity data. Results show that swirl motion is generated at the end of the intake stroke and persists to the end of the compression stroke. Tumble vortex is produced in the early stage of the compression stroke and distorted in the late stage of the stroke. The cyclic variation of swirl motion is noticeable. The cyclic variation in tumble dominated flow field is much greater.

This paper is concerned with the performance of the sensors and associated instrumentation used for the standard cetane tests for diesel fuels according to the ASTM D-613 procedure. The two primary sensors are replaced by modern units, and the analogue monitoring system is replaced by a digital one; the changes in the performance of the instrumentation system are then assessed. It is shown that the main source of inaccuracy in the measurement of ignition delay (on which the cetane test is based) is cyclic instability in the start of combustion, and that the current instrumentation and monitoring methods do not cope well with this instability. Although some of the cyclic variation can be ascribed to the instrumentation system, a large part is contributed by variability in the fuel ignition and injection processes. Improvements to the instrumentation and monitoring systems are presented and assessed.

Knock in gasoline engines at higher loads is a significant constraint on torque and efficiency. The anti-knock property of a fuel is closely related to its research octane number (RON). Ethanol has superior RON compared to gasoline and thus has been commonly used to blend with gasoline in commercial gasolines. However, as the RON of a fuel is constant, it has not been used as needed in a vehicle. To wisely use the RON, an On-Board Separation (OBS) unit that separates commercial gasoline with ethanol content into high-octane fuel with high ethanol fraction and a lower octane remainder has been developed. Then an onboard Octane-on-demand (OOD) concept uses both fuels in varying proportion to provide to the engine a fuel blend with just enough RON to meet the ever changing octane requirement that depends on driving pattern.

Comparisons have been made between the ignition delay and combustion performance of sunflower oil and diesel fuel. The experimental results have been obtained in a naturally aspirated direct injection diesel engine, and particular attention has been given to the heat release analysis, ignition delay, combustion noise and lubricant degradation. The anomalous behaviour of sunflower oil is explained by reference to its physical properties and ignition quality, as reported in the literature from bomb tests. It is concluded that the power output and brake efficiency are largely unaffected by the use of the sunflower oil, and that lubricant degradation is not likely to be significant. However, the build up of combustion deposits already widely reported in the literature was observed. Suggestions are made as to how this might be ameliorated through modifications to the injection system.

Due to its potential for simultaneous improvement in fuel consumption and exhaust emissions, controlled autoignition (CAI) combustion has been subject to continuous research in the last several years. At the same time, there has been a lot of interest in the use of alternative fuels in order to reduce reliance on conventional fossil fuels. Therefore, this experimental study has been carried out to investigate the effect of alcohol fuels on the CAI combustion process and on the resulting engine performance. The experimental work was conducted on an optical single cylinder engine with an air-assisted injector. To achieve controlled autoignition, residual gas was trapped in the cylinder by using negative valve overlap and an intake air heater was used to ensure stable CAI combustion in the optical engine. Methanol, ethanol and blended fuels were tested and compared with the results of gasoline.

Biobutanol, i.e. n-butanol, as a second generation bio-derived alternative fuel of internal combustion engines, can facilitate the energy diversification in transportation and reduce carbon dioxide (CO2) emissions from engines and vehicles. However, the majority of research was conducted on spark-ignition engines fuelled with n-butanol and its blend with gasoline. A few investigations were focused on the combustion and exhaust emission characteristics of homogeneous charge compression ignition (HCCI) engines fuelled with n-butanol-gasoline blends. In this study, experiments were conducted in a single cylinder four stroke port fuel injection HCCI engine with fully variable valve lift and timing mechanisms on both the intake and exhaust valves. HCCI combustion was achieved by employing the negative valve overlap (NVO) strategy while being fueled with gasoline (Bu0), n-butanol (Bu100) and their blends containing 30% n-butanol by volume (Bu30).

Homogeneous charge compression ignition (HCCI) technology is promising to reduce engine exhaust emissions and fuel consumption. However, it is still confronted with the problem of its narrow operation range that covers only the light and medium loads. Therefore, to expand the operation range of HCCI, mode switching between HCCI combustion and transition SI combustion is necessary, which may bring additional problems to be resolved, including load fluctuation and increasing the complexity of control strategy, etc. In this paper, a continuously adjustable load strategy is proposed for gasoline engines. With the application of the strategy, engine load can be adjusted continuously by the in-cylinder residual gas fraction in the whole operation range. In this research, hybrid combustion is employed to bridge the gaps between HCCI and traditional SI and thus realize smooth transition between different load points.

A Variable Valve Timing system has been designed and rig tested for application on a high speed marine diesel engine. It has been demonstrated that inlet valve phasing is an appropriate way of reducing the flow of exhaust gas residuals, particularly at light loads, into the inlet manifold during valve overlap. The system described controls the position of the roller follower by means of an eccentric to allow the inlet valve events to be retarded by up to 40° crank angle. A kinematic model has been constructed to examine the tappet motion, and comparisons are made with measured values. Modelling of the lubrication regime at the roller, cam and tappet contact points is presented, to examine the system wear characteristics. Roller follower speed is measured to examine the prevailing lubrication regime. Rig results show that the VVT system is reliable and that the desired phasing of the valve events is obtained.

Fuel cell electric vehicles offer an attractive option for decarbonizing long-haul on-road transport. However, there are still several barriers to widespread adoption of hydrogen-fueled fuel cells for this application including system durability and total cost of ownership compared to traditional diesel engines. A primary contributor to fuel cell system costs and maintenance requirements is the air management system. It is common for heavy duty fuel cell electric vehicles to use light-duty automotive air management components which are ill-suited for the requirements of larger, long-haul vehicles. This study focuses on the development of a durable and efficient air management system for heavy duty vehicle applications as part of a cooperative research project funded by the Department of Energy’s Hydrogen and Fuel Cell Technologies Office1.