Search Results

This paper describes efforts to use computational fluid dynamics (CFD) to provide some general insights on how wall-based protuberances affect the flow and thermal fields in substrates exposed to typical diesel engine exhaust conditions. The channel geometries examined included both square and round bumps as well as an extreme tortuous path design. Three different 2d CFD laminar-flow analyses were performed: (1) a transient fluid analysis to identify the existence of any vortex shedding in the vicinity of the bumps, (2) a steady-state fluid analysis to examine the velocity and pressure fields as well as momentum transport characteristics, and (3) a thermal analysis to examine the heat transport characteristics. The model predicts no vortex shedding behind the bumps for the conditions and geometries examined, confirming the validity of a steady state approach and eliminating this possible transport mechanism.

Accurate accounting for fresh charge (fuel and air) along with trapped RGF is essential for the subsequent thermodynamic analysis of combustion in gasoline engines as well as for on-line and real-time quantification as relevant to engine calibration and control. Cost and complexity of such techniques renders direct measurement of RGF impractical for running engines. In this paper, an empirically-based approach is proposed for on-line RGF, based on an existing semi-empirical model [1]. The model developed expands the range over which the semi-empirical model is valid and further improves its accuracy. The model was rigorously validated against a well correlated GT-POWER model as well as results from 1D gas exchange model [2]. Overall, using this model, RGF estimation error was within ∼1.5% for a wide range of engine operating conditions. The model will be implemented in Dyno development and calibration at Chrysler Group.

Increasingly stringent vehicle emissions legislation is being introduced throughout the world, regulating the allowed levels of particulate matter emitted from vehicle tailpipes. The regulation may prove challenging for gasoline vehicles equipped with modern gasoline direct injection (GDI) technology, owing to their increased levels of particulate matter production. It is expected that gasoline particulate filters (GPFs) will soon be fitted to most vehicles sold in China and Europe, allowing for carbonaceous particulate matter to be effectively captured. However, GPFs will also capture and accumulate non-combustible inorganic ash within them, mainly derived from engine oil. Studies exist to demonstrate the impact of such ash on GPF and vehicle performance, but these commonly make use of accelerated ash loading methods, which themselves introduce significant variation.

In the auto industry, lightweight window designs are drawing more attention for improved gas mileage and reduced exhaust emission. Corning’s Gorilla® Glass used in laminate design enables more than 30% weight reduction compared to conventional soda-lime glass laminates. In addition, Gorilla® Glass hybrid laminates (which are a laminate construction of a thick soda-lime glass outer play, a middle polyvinyl butyral interlayer, and a thin Gorilla Glass inner ply) also show significantly improved toughness due to advanced ion-exchange technology that provides high-surface compression. However, the reduced mass also allows increased transmission of sound waves through the windshield into the vehicle cabin. A system-level measurement approach has always been employed to assess overall vehicle acoustic performance by measuring sound pressure levels (SPL) at the driver’s ears. The measured sound signals are usually a superimposition of a variety of noise sources and transmission paths.

Optimization of the interface between the powerplant and vehicle frame/body is critical to obtaining superior interior structureborne noise and vibration characteristics in the vehicle. This paper demonstrates the combination of new and existing simulation/experimental methodologies for powerplant integration, including results from case studies. Multi-body simulation based methodologies are used to optimize the location, number, and type of powerplant mounts on a vehicle, taking into account the input forcing from the engine and frequency-dependent mount properties. Upon obtaining the first prototype vehicle, a procedure to evaluate the effectiveness of the powerplant mounts using a vibrational power flow technique, is described. The influence of mount bracket resonances on interior vehicle sound is shown and a new procedure to optimize mount brackets, provided.

NVH refinement is an important aspect of the powertrain development process. Powertrain NVH refinement is influenced by overall sound levels as well as sound quality. The sound quality and hence the level of powertrain NVH refinement can be negatively affected by the presence of excessive impulsive noise. This paper describes a process used to develop an understanding of impulsive powertrain noise. The paper begins with an introductory discussion of various sources of impulsive noise in an automotive powertrain. Following this, the paper outlines a process for identifying the source of the impulsive powertrain noise using examples from case studies. The remainder of the paper focuses on certain examples of impulsive noise such as Diesel knocking noise, injector ticking, impulsive cranktrain noise, and gear rattle. For these examples, the development of key objective metrics, optimization measures, and improvement potential are examined.

Driven mainly by tightening of regulations, advance diesel emission control technologies are rapidly advancing. This paper will review the field with the intent of highlighting representative studies that illustrate the state-of-the-art. First, the author makes estimates of the emission control efficiency targets for heavy and light duty applications. Given the emerging significance of ultrafines to health, and to emission control technologies, an overview of the significant developments in ultrafine particulate science is provided, followed by an assessment of filter technology. Major deNOx catalyst developments, in addition to SCR and LNT progress is described. Finally, system integration examples are provided. In general, progress is impressive and studies have demonstrated that high-efficiency systems are within reach in all sectors highway vehicle sectors. Engines are making impressive gains, and will increase the options for emission control.

Due to the future application of combustion engines in small and hybrid vehicles, the demand for high efficiency with low mass and compact engine design is of prime importance. The diesel engine, with its outstanding thermal efficiency, is a well suited candidate for such applications. In order to realize these targets, future diesel engines will need to have increasingly higher specific output combined with increased power to weight ratios. This is therefore driving the need for new designs of 3 and/or 4 cylinder, small bore engines of low displacement, sub 1.5l. Recent work on combustion development, has shown that combustion systems, ports, valves and injector sizes are available for bore sizes down to 65 mm.

The tightening of emissions regulations has required changes in many areas of vehicle systems, including calibration strategies, catalytic converter strategies and exhaust configurations. Engine calibration strategies can be engineered to complement the performance parameters of the converter. Knowledge of the precise window of converter performance for different substrates can therefore provide guidance in targeting engine calibration strategies as well as selecting compatible converter systems within calibration constraints. In a previous paper [5], we explored the effect of thermal mass on emissions performance in the context of the FTP. This paper expands on the previous work and explores the effect of the aging cycle and thermal mass differences on CO-NOx crossover and light-off profiles. This analysis provides a tool to assist in design by defining a window of performance in the converter to be used in matching to a window of operation in the calibration.

An axisymmetric finite element model is generated to simulate the windshield glass damage propagation subjected to impact loading of a flying object. The windshield glass consists of two glass outer layers laminated by a thin poly-vinyl butyral (PVB) layer. The constitutive behavior of the glass layers is simulated using brittle damage mechanics model with linear damage evolution. The PVB layer is modeled with linear viscoelastic solid. The model is used to predict and examine through-thickness damage evolution patterns on different glass surfaces and cracking patterns for different windshield designs such as variations in thickness and curvatures.

The combustion process in an IC engine is of significant importance for its noise and vibration characteristics in the vehicle. Describing the combustion process with thermodynamic metrics typically demands extensive instrumentation of the engine to obtain the cylinder pressure from the combustion chamber. This time consuming task often requires, that the engine be removed from the vehicle, instrumented with pressure transducers, and then either reinstalled in the vehicle and tested or installed in a test cell and evaluated. This paper describes a new relatively simple approach towards examining important combustion parameters. The technique is based on statistical analysis of the crankshaft's speed fluctuation. This approach requires relatively simple instrumentation of the engine and is therefore more applicable for vehicle level investigations.

With rising gasoline prices in the US the need for increasingly fuel efficient powertrain concepts has never been more critical. Evaluation of the market on the other hand shows that the vehicle-buying consumer is unwilling to compromise engine power output for this needed fuel efficiency. Boosted, direct-injected gasoline engines with high specific output and low end torque seem to be the most logical path to satisfying both good part load fuel economy and generous power and torque characteristics. Turbo lag and subsequent lack of torque during transient acceleration (with low initial engine speeds) are characteristics of current turbocharged gasoline engines. These phenomena have prevented successful penetration of these boosted powertrains into the marketplace. Larger displacement, naturally aspirated gasoline engines have been the preferred choice.

The present work intends to examine the selective NOx reduction efficiency of a current commercial Titanium-Vanadium washcoated catalyst and to develop a transient numerical model capable of describing the SCR process while using a wide range of inlet conditions such as space velocity, oxygen concentrations, water concentration and NO2/NO ratio. The concentrations of different components (NO, NO2, N2O, NH3, H2O and HNO3) were analyzed continuously by a FT-IR spectrometer. A temperature range from 150°C up to 650°C was examined and tests were carried out using a model exhaust gas comparable to the real diesel exhaust gas composition. There is a very good correlation between experimental and calculated results with the given chemical kinetics.

Diesel particulate filters (DPF) have become a standard aftertreatment component for a majority of current on-road/non-road diesel engines used in the US and Europe. The upcoming Stage V emissions regulations in Europe will make DPFs a standard component for emissions reductions for non-road engines. The tightening in NOx emissions standard has resulted in the use of selective catalytic reduction (SCR) technology for NOx reduction and as a result the general trend in engine technology as of today is towards a higher engine-out NOx/PM ratio enabling passive regeneration of the DPF. The novel filter concept discussed in this paper is optimized for low pressure drop, high filtration efficiency, and low thermal mass for optimized regeneration and fast heat-up, therefore reducing CO2 implications for the DPF operation.

With the introduction of a stringent particulate number (PN) limit and real driving emission (RDE) requirements, gasoline particulate filters (GPF) are widely adopted for gasoline engines in Europe and China. The filter collects soot and ash. Like in diesel applications, the collected soot will continuously burn under favorable exhaust conditions. However, at extreme conditions, there could be large amounts of soot build-up, which may induce a highly exothermal event, potentially damaging the filter. Thus, it is important to understand what drives the over-heating in application, and develop counter measures. In this study, an on-vehicle fuel cut (FC) testing procedure was developed. The testing was conducted on two vehicles, one gasoline direct injection (GDI) vehicle and one multiple port injection (MPI) vehicle, with different exhaust systems designs (a close coupled GPF and an under floor GPF) and catalyst coating levels (bare and heavily coated GPFs).

The new opoc™ diesel engine concept was presented at the SAE 2005 World Congress [1]. Exceptional power density of >1hp/lb and >40% efficiency have been predicted for the 2-stroke opoc™ diesel engine concept. Intensive CAE simulations have been performed during the concept and design phase in order to define the baseline scavenging and combustion parameters, such as port timing, turbocharger configuration and fuel injection nozzle design. Under a DARPA contract, first prototype engines have been built and have undergone a validation testing program. The main goal of the first testing phase was to demonstrate the power output capability of the new engine concept. In close relationship and interaction of testing and CAE simulation, the uniflow scavenging process and parameters of the special diesel direct side injection have been optimized. This paper discusses the latest results of the opoc engine development.

The opposed piston opposed cylinder (opoc™) engine concept has been demonstrated as an engine concept with high specific power density and high power to volume ratio. The engine has several potential applications, including use as an auxiliary power unit (APU) in various commercial and military applications and as the primary power source for small unmanned air vehicles (UAVs). An engine in this power range operating on heavy fuels (e.g. JP5, JP8, DF2) is not typically available. The engine uses a two-cycle supercharged uniflow scavenging system with asymmetric port timing and will run at speeds between 8,000 and 12,000 rpm. The unique design of the opoc™ engine produces a piston speed that is half the speed of a typical crankshaft engine running at the same speed. Uniflow scavenging produces gas exchange efficiencies rivaling those of four-cycle engines. The design also leads to reduced in-cylinder heat losses. Furthermore, the opoc™ engine is fully balanced.

Over the past decade, regulations for mobile source emissions have become more stringent thus, requiring advances in emissions systems to comply with the new standards. For the popular diesel powered passenger cars particularly in Europe, diesel particulate filters (DPFs) have been integrated to control particulate matter (PM) emissions. Corning Incorporated has developed a new proprietary aluminum titanate-based material for filter use in passenger car diesel applications. Aluminum titanate (hereafter referred to as AT) filters were launched commercially in the fall of 2005 and have been equipped on more than several hundred thousand European passenger vehicles. Due to their outstanding durability, filtration efficiency and pressure drop attributes, AT filters are an excellent fit for demanding applications in passenger cars. Extensive testing was conducted on engine to evaluate the survivability and long-term thermo-mechanical durability of AT filters.

Based on the TurboDISI engine presented earlier [1], [2], a new Spray Guided Turbo (SGT) concept with enhanced engine performance was developed. The turbocharged engine was modified towards utilizing a spray-guided combustion system with a central piezo injector location. Higher specific power and torque levels were achieved by applying specific design and cooling solutions. The engine was developed utilizing a state-of-the-art newly developed charge motion design (CMD) process in combination with single cylinder investigations. The engine control unit has a modular basis and is realized using rapid prototyping hardware. Additional fuel consumption potentials can be achieved with high load EGR, use of alternative fuels and a hybrid powertrain. The CO2 targets of the EU (120 g/km by 2012 in the NEDC) can be obtained with a mid-size vehicle applying the technologies presented within this paper.

The diesel oxidation catalyst is required to remove hydrocarbons and carbon monoxide from the diesel engine exhaust stream while minimizing the impact of all other features such as cost, space, pressure drop, weight, fuel consumption, etc. The challenge of designing a catalytic converter for a particular application then becomes to: first, understand the emissions and other performance targets and requirements for the engine; second, understand the influence each of the converter parameters has on the overall system performance and; third, optimize the system using these relationships. This paper will explore some of the considerations with respect to the second of the above challenges.