Search Results

It is now well established that highly turbulent flows in engines are responsible for cycle-to-cycle aerodynamic variations particularly in cylinder. These dispersions may lead to macroscopic changes in flow pattern from one cycle to another one, which are quite different from “true turbulence” (in fact small scale turbulent fluctuations) used to optimize combustion. It is of a great importance to decrease these variations which may effect reliability of combustion concept and particularly when looking to decrease idle engine speed. The difficulty in separating “true turbulence” from cyclic variations is that there is no limit between two kinds of fluctuations. To analyze aerodynamic, PIV is well adapted to study these phenomena and is now currently used in development process, allowing to measure instantaneous aerodynamics field to determine for instance vortex center position for each cycle.

This paper presents a new 0D phenomenological approach to predict the combustion process in diesel engines operated under various running conditions. The aim of this work is to develop a physical approach in order to improve the prediction of in-cylinder pressure and heat release. The main contribution of this study is the modeling of the premixed part of the diesel combustion with a further extension of the model for multi-injection strategies. In phenomenological diesel combustion models, the premixed combustion phase is usually modeled by the propagation of a turbulent flame front. However, experimental studies have shown that this phase of diesel combustion is actually a rapid combustion of part of the fuel injected and mixed with the surrounding gas. This mixture burns quasi instantaneously when favorable thermodynamic conditions are locally reached. A chemical process then controls this combustion.

Biofuels are a renewable energy source. When used as extenders for transportation fuels, biofuels contribute to the global reduction of Green House Gas and CO2 emissions from the transport sector and to security and independence of energy supply. On a “Well to Wheel” basis they are much more CO2 efficient than conventional fossil fuels. All vehicles currently in circulation in Europe are capable of using 5 % biodiesel. The introduction of higher percentages biodiesel needs new specific standards and vehicle tests validation. The development of vehicles compatible with 30% biodiesel blends in diesel fuel includes the validation of each part of both engine and fuel vehicle systems to guarantee normal operation for the entire life of the vehicle.

Progress in Diesel spray modelling highly depends on a better knowledge of the instantaneous injection velocity and of the hydraulic section at the exit of each injection hole. Additionally a better identification of the mechanisms which cause fragmentation is needed. This necessitates to begin with a precise computation of the two-phase flow which arises due to the presence of cavitation within the injectors. For that aim, a VOF type interface tracking method has been developed and improved (Segment Lagrangian VOF method) which allows to describe numerically the onset and development of cavitation within Diesel injectors. Furthermore, experiments have been performed for validation purpose, on transparent one-hole injectors for high pressure injection conditions. Two different entrance geometries (straight and rounded) and various upstream and downstream pressure levels have been considered.

This paper introduces a research work on the air loop system for a downsized two-stroke two-cylinder diesel engine conducted in framework of the European project dealing with the POWERtrain for Future Light-duty vehicles - POWERFUL. The main objective was to determine requirements on the air management including the engine intake and exhaust system, boosting devices and the EGR system and to select the best possible technical solution. With respect to the power target of 45 kW and scavenging demands of the two-cylinder two-stroke engine with a displacement of 0.73 l, a two-stage boosting architecture was required. Further, to allow engine scavenging at any operation, supercharger had to be integrated in the air loop. Various air loop system layouts and concepts were assessed based on the 1-D steady state simulation at full and part load with respect to the fuel consumption.

Studies using a bi-fuelled (autogas/gasoline) Renault Laguna vehicle meeting °the 1996 European exhaust emission legislation has demonstrated that over the European test cycle at 25°C the LPG operated vehicle provides substantial benefits of reduced emissions compared to unleaded reference gasoline. At lower test temperatures (i.e. 5°C) even larger reduction in emissions have been observed. Lower CO (up to 95% at -5°C and 65% at 25°C), HC (90% at -5°C and 40% at 25°C) emissions and lower ozone HC reactivity have been observed and could all offer significant environmental air-quality benefits for LPG. Various autogas mixtures have been tested including 70/30, 30/70 and 49/30/21 (% mass propane / butane / propene). Results show that NOx emissions for this vehicle appear dependent on autogas composition. The two gas mixtures containing only 30% butane gave about 50% more NOx at +25°C than the 70% butane autogas mixture.

In order to simulate the working process, an accurate description of heat transfer occurring between in-cylinder gases and combustion chamber walls is required, especially regarding thermal efficiency, combustion and emissions, or cooling strategies. Combustion chamber wall heat transfer models are dominated by zero-dimensional semi-empirical models due to their good compromise between accuracy, complexity and computational efficiency. Classic models such as those from Woschni, Annand or Hohenberg are still widely used, despite having been developed on rather ancient engines. While numerous authors have worked on this topic in the past decades, little information can be found concerning the systematic calibration process of heat transfer models. In this paper, a systematic calibration method based on experimental data processing is tested on the complete operating map of a turbocharged GDI engine.

The description of the supply pressure hydraulic circuit and the couplings between its components are presented. A comparison between simulations and experiments is carried out. Using some linear facilities, it is possible to conclude that the low frequency modes mainly correspond to the wave effects of hydraulic lines which connect valves to each other. In order to maintain a pressure in the supply circuit, an electronic pressure control is necessary. The design of a control law needs to build different linear models for different levels of pressure since the system is very non linear. Three transfer functions are found for three pressure levels. These transfer functions are very similar to the ones used by the automatic control department and obtained by experiments. Using these transfer functions it is possible to design the control law.

3D simulations of internal combustion engines are usually based on statistical approaches (RANS) that may not allow predicting cycle-to-cycle variations (CCV) or transient speeds because part of this information is lost by the averaging procedure. To simulate such phenomena, it requires time resolved approaches. Therefore, large eddy simulation (LES), which only involves a spatial averaging, appears to be a very promising tool. An LES approach is applied to simulate the flow field inside one cylinder taken from a real four-valve diesel engine mounted on an experimental particle image velocimetry (PIV) bench. Preliminary tests are carried out to evaluate the industrial code capabilities. A multi-cycle calculation is computed in cold flow, in order to evaluate its ability to simulate cycle-to-cycle variations (CCV).

Atomizing systems must be able to form sprays with predetermined characteristics. There are affected by the shape of the injector as well as external conditions. Thus, in order to avoid numerous experiments, this is necessary to develop predictive atomization models able to deal with the complete atomization process. This can be done using a Eulerian model for primary break-up. This approach describes the flow continuously from inside the injector to the dispersed spray region. In this paper the Eulerian multiphase approach and the Eulerian single-phase approach are compared and the results lead to an intermediate quasi-multiphase approach for describing the spray core. Finally a transition zone permits to represent the diluted spray region by using the classical Lagrangian approach to benefit of the experience accumulated on this method, in particular for the vaporization and the combustion.

Renault believes that the behavior of the vehicle must always be consistent with the instantaneous orders given by the driver, whether braking, accelerating or lifting the foot off the accelerator. The vehicle must also inform its driver when it is near a point of limit. The first part of this paper details the vehicle with respect to its trajectory at stabilized speeds. The rigidity of the overall drift of the axle assemblies and tires, the steering angles induced by vehicle roll attitude, under- and over-steering behavior and vehicle roll attitude, under- and over-steering behavior and behavior of the tire under load are covered. A vehicle trajectory model is used to confirm test results.

The paper provides an overview of a developed methodology and a toolchain for modeling and control of a complex aftertreatment system for passenger cars. The primary objective of this work is to show how the use of this methodology allows to streamline the development process and to reduce the development time thanks to a model based semi-automatic control design methodology combined with piece-wise optimal control. Major improvements in passenger car tailpipe NOx removal need to be achieved to fulfil the upcoming post EURO 6 norms and Real Driving Emissions (RDE) limits. Multi-brick systems employing combinations of multiple Selective Catalytic Reduction (SCR) catalysts with an Ammonia Oxidation Catalysts, known also as Ammonia Clean-Up Catalyst (CUC), are proposed to cover operation over a wide temperature range. However, control of multi-brick systems is complex due to lack of available sensors in the production configurations.

Electrical Low Pressure Impactor (ELPI) is often employed to measure the particle number and size distribution of internal combustion engines exhaust gas. If appropriate values of particle density are available, the particle mass can be estimated by this method. Exhaust particles of three Euro3 passenger cars (one gasoline operating under stoichiometric conditions, one Diesel and one Diesel equipped with Diesel Particulate Filter) are measured using the current European regulations (gravimetric method on the are New European Driving Cycle) and estimated by ELPI particle number and size distribution. Different values for particle density are used to estimate the particle mass using all ELPI stages or only some of them. The results show that the particle mass estimated by ELPI is well correlated with the mass determined by filters for PM emissions higher than 0.025 g/km. This correlation is not very good at lower emissions.

0D-1D codes allow researchers to obtain a prediction of the behavior of internal combustion engines with little computational effort. One of the submodels of such codes is devoted to the centrifugal compressor. This model is often based on the compressor performance maps, therefore requiring the extrapolation of the maps so that all possible operating conditions are covered. Particularly, a suitable extrapolation of isentropic efficiency map is sought. This work first examines different available methods for compressor efficiency extrapolation into off-design conditions. No method is found to provide satisfactory results at all extrapolated regions: low and high compressor speeds and low compression ratio at measured speeds. Hence, a new method is proposed and its accuracy is assessed with the aid of compressor off-design measurements.

Fuel consumption in internal combustion engines and their associated CO2 emissions have become one of the major issues facing car manufacturers everyday for various reasons: the Kyoto protocol, the upcoming European regulation concerning CO2 emissions requiring emissions of less than 130g CO2/km before 2012, and customer demand. One of the most efficient solutions to reduce fuel consumption is to downsize the engine and increase its specific power and torque by using turbochargers. The engine and the turbocharger have to be chosen carefully and be finely tuned. It is essential to understand and characterise the turbocharger's behaviour precisely and on its whole operating range, especially at low engine speeds. The characteristics at low speed are not provided by manufacturers of turbochargers because compressor maps cannot be achieve on usual test bench.

To reach high levels of boost pressure for downsizing on Diesel engine, new turbocharging systems for in line 4 cylinder engines have been investigated. The purpose of this work is to evaluate the two stage turbochargers potential for passenger car applications by simulations. A 2.0l diesel engine has been taken as reference (Torque and Power for all engine speeds), and the aim of this work is to develop a 1.5l diesel engine able to reach this target. The boost system architecture investigated consists two turbochargers in series with one intercooler after each compressor. Simulations have been performed with GT-Power. Turbine and compressor wheels have been modified on both stages in order to define the best combination. Results have shown that the steady state performance can be reached quiet easily. These results made us focus on transient aspect of this concept. A vehicle inertia model has been set up.

Lean NOx trap (LNT) and Selective Catalytic Reduction catalysts (SCR) are two leading candidates for diesel NOx after-treatment. Each technology exhibits good properties to reduce efficiently diesel NOx emissions in order to match the forthcoming EURO 6 standards. NOx reduction in LNT is made through a two-step process. In normal (lean) mode, diesel engine exhausts NOx is stored into the NOx trap; then when necessary the engine runs rich during limited time to treat the stored NOx. This operating mode has the benefit of using onboard fuel as NOx reducer. But NOx trap solution is restrained by limited active temperature windows. On the other hand, NH₃-SCR catalysts operate in a wider range of temperature and do not contain precious metals. However, NH₃-SCR systems traditionally use urea-water solution as reducing agent, requiring thus additional infrastructure to supply the vehicles with enough reducer. These pros and cons are quite restrictive in classical LNT or NH₃-SCR architecture.

The current trend of downsizing used in gasoline engines, while reducing fuel consumption and CO2 emissions, imposes severe thermal loads inside the combustion chamber. These critical thermodynamic conditions lead to the possible auto-ignition (AI) of fresh gases hot-spots around Top-Dead-Center (TDC). At this very moment where the surface to volume ratio is high, wall heat transfer influences the temperature field inside the combustion chamber. The use of a realistic wall temperature distribution becomes important in the case of a downsized engine where fresh gases hot spots found near high temperature walls can initiate auto-ignition. This paper presents a comprehensive numerical methodology for an accurately prediction of thermodynamic conditions inside the combustion chamber based on Conjugate Heat Transfer (CHT).

Reducing NOx tailpipe emissions is one of the major challenges when developing automotive Diesel engines which must simultaneously face stricter emission norms and reduce their fuel consumption/CO2 emission. In fact, the engine control system has to manage at the same time the multiple advanced combustion technologies such as high EGR rates, new injection strategies, complex after-treatment devices and sophisticated turbocharging systems implemented in recent diesel engines. In order to limit both the cost and duration of engine control system development, a virtual engine simulator has been developed in the last few years. The platform of this simulator is based on a 0D/1D approach, chosen for its low computational time. The existing simulation tools lead to satisfactory results concerning the combustion phase as well as the air supply system. In this context, the current paper describes the development of a new NOx emission model which is coupled with the combustion model.

Diesel Particulate Filters (DPF) are now considered as efficient solutions to reduce Diesel PM emissions. Concerned by environment, Renault will equip all serial production Diesel vehicles with this technology. The main issue for these devices is the periodical regeneration necessary to eliminate the accumulated soot. The challenging enhancement of the regeneration event can be achieved with a better regeneration temperature control. For this purpose, a controller based on a physical model is proposed to manage the DPF temperature during active regeneration. This paper describes the methodology which has been followed to design this controller. In a first step, a reduced physical model has been developed and validated with experimental data. In a second step, two model-based controllers have been studied: a robust LPV (Linear Parameter Varying) and a gain scheduling PID..Special attention has been paid to the simplification as far as possible of the controller tuning process.