Search Results

The international Lubricant Standardization and Approval Committee (ILSAC) GF-2 specification requires Passenger Car Motor Oils to provide enhanced fuel economy in a modern low friction engine (ASTM Sequence VIA). In previous SAE publications the authors have studied the boundary lubrication regime and documented the impact of friction modifiers and antiwear additives on Sequence VIA fuel economy. This paper shifts the focus to the hydrodynamic lubrication regime and details fundamental studies of viscosity modifiers and base oils on fuel economy as measured by this low friction engine. The viscosity modifiers were found to have surprisingly little impact on this test, while moving to base oils of higher viscosity index improved fuel economy as might be theoretically expected. A study of formulating SAE 5W-30 motor oils with base oils of increasing viscosity index showed the optimum fuel economy was able to be obtained with a high viscosity index base stock.

There is concern over water-in-oil emulsion formation in passenger cars in the field. Crankcase pressure measurements in the ASTM Sequence IID rust test have been used to indicate possible emulsion formation tendencies of lubricants. This paper presents the development of a short duration emulsion fleet test procedure which demonstrates low car-to- car variability and correlates well with a previous fourmonth winter emulsion fleet test. Physical emulsion characteristics and used oil analyses are described. Evaluation of both Sequence IID reference oils and commercial oils in this field test reveals a lack of correlation between Sequence IID crankcase pressure results and field performance. The new procedure has been applied to investigate the impact of additive and base oil variations on the emulsion-forming tendencies of lubricants in the field. Base oil variables such as viscosity grade, composition, and volatility were evaluated.

The technology has been developed which will allow manufacturers to produce cars capable of running on methanol/gasoline blends with a methanol content up to 85% (i.e., M85). These cars will operate on varying methanol/gasoline ratios without any adjustments from the driver. The dual-fuel capability is attractive since vehicle use will not be handicapped by a restricted fuel distribution system. In addition, it provides the option of running on an environmentally “cleaner” fuel where it is available. The advent of fuel-flexible vehicles encourages the development of lubricants which will satisfy the demands of both fuels. The unique properties of methanol, however, increase the challenges of meeting the lubricant performance needs. Field and engine dynamometer testing have been aimed at understanding the response of key lubricant variables with M85. Short-trip, cold-weather conditions have been of particular concern.

Driven by global demands for improved fuel economy and reduced emissions, significant improvements have been made to engine designs and control systems, vehicle aerodynamics, and fuel quality. Improvements, such as the continuously slipping torque converter, have also been made to automatic transmissions to increase vehicle efficiency. Recently, belt-continuously variable transmissions (b-CVTs) have been commercialized with the promise of significant fuel economy improvements over conventional automatic transmissions. Automotive traction drive transmissions may soon join belt-CVTs as alternative automatic transmission technology. Much of the information reported in technical and trade publications has been on the mechanics of these traction drive systems. As automotive traction drives move closer to commercial reality, more attention must be given to the performance requirements of the automotive traction fluid.

Two prominent trends are facing diesel engine builders and their customers, environmental regulations and cost containment. Increasingly stringent exhaust emissions regulations have necessitated major changes in diesel engine design. Combustion temperatures and fuel injection pressures continue to rise. This and other factors, such as lower oil consumption for exhaust particulate reduction, place greater demands on crankcase lubricating oils. Another prominent environmentally related cost factor facing fleet operators is that of waste oil management. The inventory and disposal of used lubricants must now be handled in accordance with regulated guidelines and their associated costs. To compensate, new lubricant categories have been designed in both North America and Europe, such that 1994 and later emission controlled engines will perform as reliably as their earlier counterparts.

Requirements to reduce emissions and improve vehicle fuel economy continue to increase, spurred on by agreements such as the Kyoto Protocol. Lubricants can play a role in improving fuel economy, as evidenced by the rise in the number of engine oil specifications worldwide that require fuel economy improvements. A novel friction modifier technology has been developed to further improve vehicle fuel economy. The development of this novel friction modifier technology which contains only N,O,C,H was previously published along with the initial demonstration of performance in motorized Toyota engines. In order to validate this performance in fired engine tests, oil was evaluated in a Toyota Corolla Fielder with a 1500 cc gasoline engine. Testing was conducted in the Japanese 10-15 and JC08 modes, as well as the European EC mode, and the US FTP mode.

This paper describes the development of a image analysis system that can be used to rate injectors from the Cummins L10 Injector Depositing Test. In the procedure, injectors are mounted on a computer controlled turntable and scanned using a CCD camera focused on the labyrinth flow area of the injector. The scanned monochrome images are processed and assigned an average gray scale rating. Results from the image analysis system are compared to the modified CRC Piston and Ring Rating method currently used within the Cummins test procedure. To do this, a series of injectors that have been rated by trained raters at a recent workshop were also rated via the image analysis system. The image analysis system ratings demonstrated a strong correlation (R = 0.85) to the CRC ratings. Using these same injectors, the image analysis method shows improvements in repeatability and reproducibility of approximately 50% over the current procedure.

A test method has been developed which provides for the rapid measurement of the scuffing performance of diesel fuel using the Ball-On-Cylinder Lubricity Evaluator (BOCLE). A test can be completed in less than one hour. Data has been generated indicating that the method achieves good discrimination between fuels of varying lubricity and correlates well with fuel performance as measured in pump tests.

A test was developed by the Cummins Engine Company to evaluate Diesel fuel quality and potential additive effects. This test utilizes a Cummins L10 Diesel engine with a PT fuel system and stepped plunger injectors. A modified CRC rating system is used to quantify deposit levels. This paper further investigates the L10 Injector Depositing Test and will focus on Diesel fuel and additive variables. In the original work, the bulk of the data was collected on an industry standard reference fuel, Cat 1-H, as opposed to commercially available Diesel fuels. Commercially available Diesel fuel varies in composition with regard to sulfur level, percent aromatics, final distillation end point, and cetane number. To evaluate these fuel properties and their possible effects on injector deposit formation, two test matrices were designed. The first experiment is a 12-run fractional factorial design with four factors: additive level, sulfur, aromatics, and 90 percent distillation point (T90).

The effects of gasoline composition, as represented in typical regular and premium unleaded gasolines and fuel additives, on Combustion Chamber Deposits (CCD) were investigated in BMW and Ford tests. In addition, the influences of engine lubricant oil and ethanol oxygenate on CCD were examined in Ford 2.3L engine dynamometer tests. Also, additive effects of packages based on mineral oil fluidizers versus synthetic fluidizers were studied in several different engines for CCD. Finally, a new method for evaluating the effect of fluidizers on valve sticking is introduced.

A discriminating dynamometer-based test was developed for evaluating cold start and warmup engine performance based on in-cylinder pressure measurements. The dynamometer test offers advantages in time required, flexibility and reduced variability over the vehicle procedure on which it was based. A parametric study on fuel driveability index (DI), ethanol content and intake valve deposit (IVD) rating demonstrated that each of these parameters had a statistically significant impact on engine cold start performance. Simple numerical offsets to fitted models based on oxygen content of the fuel did not account for the difference in engine performance of hydrocarbon-only versus ethanol-containing fuels. The effect of IVD on engine performance did not appear to depend on the DI of the fuel. The benefits of cleaner valves are seen even in fuels of very low DI.

Accurate, timely field test results are necessary to develop and validate lubricants meeting frequently changing performance requirements. Field tests can also provide valuable information about performance deficiencies (e.g., soot related wear) which are not apparent in laboratory development tests. Since field tests are time intensive and increasingly expensive, it is imperative that the data generated provide meaningful results with reasonable expenditures. The data generation and analysis process are being constantly improved according to the principles of quality management. Part of the process improvement focuses on accurate, realistic treatment of the data since more variation is typically observed in field tests than in laboratory tests. One of the most difficult analytical processes occurs with oil consumption data.

The International Lubricant Standardization and Approval Committee (ILSAC) GF-2 requirements for Passenger Car Motor Oils (PCMOs) will lower phosphorus limits from a maximum of 0.12% allowed by ILSAC GF-1 to a maximum of 0.10%. In effect, the ILSAC GF-2 phosphorus limit removes 17% of the most commonly used antiwear and antioxidant additive in current PCMOs, zinc dialkyldithiophosphate (ZDP). This paper outlines some work in ASTM Sequence V engine dynamometer tests to quantify the effect of reducing the ZDP on valve train wear and sludge formation. Engine data for the Sequence VE, the proposed Sequence VF, and the modified Sequence VE are presented. These three tests summarize the evolution of the Sequence V from the Sequence VE for GF-1 to the dual plug Sequence VE configuration for the GF-2 specification.

The proposed International Lubricant Standardization and Approval Committee (ILSAC) GF-2 specification requires Passenger Car Motor Oils to provide enhanced fuel economy in a modern low friction engine (Sequence VIA). This paper details fundamental studies of lubricant effects on fuel economy as measured by this low friction engine. Several conventional friction modifiers were tested with surprising results. One ester friction modifier, Ester B, which provides excellent fuel economy improvement in the Sequence VI, was found to be detrimental to the Sequence VIA. A second ester friction modifier, Ester A, performed as expected. Additionally, two molybdenum compounds, which are reported to provide excellent fuel economy in the Sequence VI, showed no fuel economy benefit in the Sequence VIA.

Motorcycle manufacturers have recognized that highly friction modified passenger car oils can be deleterious to clutch performance, leading to clutch slippage. To address this issue, a JASO specification for four-stroke motorcycle oils was developed in 1999, categorizing oils into high friction oils termed JASO MA and low friction oils termed JASO MB. The high friction oils were preferred for most motorcycles where the engine oil also lubricates the clutch and gears. New motorcycle transmission technologies have increased the number of dry clutch applications which has led to an increased demand for JASO MB oils to improve fuel efficiency. While JASO MB oils contain friction modifiers to improve initial fuel economy, the motorcycle specifications have not addressed the fuel economy durability of motorcycle oils.

Additives are an integral part of today's fuels. Together with carefully formulated base fuel composition, they contribute to efficiency, dependability and long life of gasoline and diesel engines. As a primer, this paper describes the range of chemical additives formulated for gasoline and diesel fuel and their effects. Specific functions and benefits of additives, typical use levels, and test methods for evaluation are discussed. Additive usage may be divided into three major categories: a) to satisfy desired levels of performance in engines, b) to insure delivery of uncontaminated, on-specification fuels to the end user and c) achieve necessary chemical/physical properties as manufactured by the refiner.

Additives are an integral part of today's fuels. Together with carefully formulated base fuel composition, they contribute to efficiency, dependability and long life of gasoline and diesel engines. As a primer, this paper describes the range of chemical additives formulated for gasoline and diesel fuel and their effects. Specific functions and benefits of additives, typical use levels, and test methods for evaluation are discussed. Additive usage may be divided into three major categories: a) to satisfy desired levels of performance in engines, b) to insure delivery of uncontaminated, on-specification fuels to the end user and c) achieve necessary chemical/physical properties as manufactured by the refiner.

The authors provide evidence indicating that oils meeting only the minimum requirements of API GL-5 do not always provide adequate gear protection, especially in severe duty applications. Increases in commercial vehicle power and loading have accentuated the need for oils of greater load carrying ability. A modified version of the standard L-37 test may help identify oils that possess superior durability and thermal characteristics. Future gear lubricants should provide improved fuel economy, increased manual transmission life; and frictional characteristics that allow noise free performance in limited slip differentials.

Using a seven-step quality improvement process, some of the engine build-up factors adversely influencing the severity and precision of the Sequence VI dynamometer test were examined. Insights from engineering (theory) and database (statistical) analyses enabled a 23 factorial experiment to identify oil ring tension, piston ring side clearance, and piston fit as critical parameters in a 3-oil, 9-engine, 28-test program. High ring tension was shown to emphasize the friction reducing capability of higher performing oils and the deficiency of a lower performing oil. Interactions were noted. A helpful correlation of test severity with the engine calibration indicators was shown.

Classical journal bearing equations predict the function of oil flow in dissipating heat, thereby governing the effective viscosity of the lubricant in bearings. From this perspective, experimental dynamometer tests explored low speed, high load, high temperature, operation of four low viscosity oils. Test length was 48 hours using a 3.8L V-6 engine under steady state and cyclic conditions. With a 1.4 cP HTHSR viscosity oil the bearing distress appeared dependent on connecting rod bearing clearances serving to govern rate of oil flow through the main bearings. Front and rear main bearings exhibited severe overheat-distress. This was related to the design of the oil distribution system in the crankshaft. A severe cyclic acceleration test showed little bearing distress. Significant distress occurred only with an SAE 5W viscosity grade. SAE 5W-30 and 5W-40 multigrades showed no abnormal wear. Results were interpreted in terms of high temperature, high shear rate rheology of the test oils.