Search Results

The responses of a Hybrid III 5th percentile dummy manufactured by Denton ATD were compared to a Hybrid III 5th percentile dummy manufactured by First Technology Safety Systems (FTSS). The dummies were seated on a HYGE sled set in a representative small production sedan configuration, simulating a 60 km/h offset deformable barrier (25 g pulse) and a 22 km/h crash (11 g pulse). Three shoulder retractor anchorage positions were used to place the shoulder belt at different locations on the dummy shoulder for each of the driver (left shoulder) and passenger (right shoulder) seating positions. Chest deflections measured from the rotary potentiometer are compared to deflections calculated from the accelerometers and are reported as a function of belt load and belt position. Repeatability is evaluated at low and high deflection levels.

Static out-of-position tests were performed to identify the potential for injury as a function of position, airbag type and vehicle seat characteristics. Seat and door mounted airbags, head curtains and head tubes were evaluated. Out-of-position testing was carried out with the Hybrid III 3 year old, 6 year old and the TNO Q3 3 year old child dummies. In-position tests and a dynamic test were conducted to monitor child seat and airbag interactions and to confirm that properly restrained children would not be exposed to undue risk from a deploying side airbag. Results of the out-of-position testing suggest that current side airbag designs may cause serious and/or fatal neck and chest injuries. In-position static testing with child seats suggested a potential for intrusion into the child occupant space leading to structural damage of the car seat.

This technical paper presents the results of biomechanical testing conducted on the ES-2 dummy by the Occupant Safety Research Partnership and Transport Canada. The ES-2 is a production dummy, based on the EuroSID-1 dummy, that was modified to further improve testing capabilities as recommended by users of the EuroSID-1 dummy. Biomechanical response data were obtained by completing a series of drop, pendulum, and sled tests that are outlined in the International Organization of Standardization Technical Report 9790 that describes biofidelity requirements for the midsize adult male side impact dummy. A few of the biofidelity tests were conducted on both sides of the dummy to evaluate the symmetry of its responses. Full vehicle crash tests were conducted to verify if the changes in the EuroSID-1, resulting in the ES-2 design, did improve the dummy's testing capability. In addition to the biofidelity testing, the ES-2 dummy repeatability, reproducibility and durability are discussed.

This technical paper presents the results from tests conducted with the ES-2re, a version of the ES-2 side impact dummy that was modified by the National Highway Traffic Safety Administration (NHTSA) to improve its performance in crash tests. Through the series of biofidelity tests conducted on the ES-2re, described in International Standards Organization (ISO) Technical Report (TR)9790 (1999), the OSRP observed a final overall biofidelity ranking of 4.1 for the ES-2re, which corresponds to an ISO classification of “marginal.” The biofidelity of the ES-2re is compared to that of the ES-2 and the WorldSID. Repeatability was also evaluated on the ES-2re based on the biofidelity test data. Additional pendulum tests were performed to assess the response of the dummy in oblique loading conditions, and results indicate that oblique loading from the front leads to significantly reduced rib deflections.

In 1998, Rouhana et al. described development of a new device, called the IR-TRACC (InfraRed - Telescoping Rod for Assessment of Chest Compression). In its original concept, the IR-TRACC uses two infrared LEDs inside of a telescoping rod to measure deflection. One LED serves as a light transmitter and the other as a light receiver. The output from the receiver LED is converted to a linear function of chest compression using an analog circuit. Tests have been performed with IR-TRACC units at various labs around the world since 1998. A first-generation IR-TRACC system was retrofit into a Q3 dummy by TNO. Similarly, a mid sized male Hybrid III dummy thorax and a small female Hybrid III dummy thorax have been designed by First Technology Safety Systems (FTSS) such that each contains 4 second-generation IR-TRACC units. The second-generation IR-TRACC is the result of continued development by FTSS, especially in the areas of the analysis circuit, manufacturing and calibration methods.

Passenger car side impact crash tests and sled tests were conducted to investigate the influence of booster seats, near-side occupant characteristics and vehicle interiors on the responses of the Q6/Q6s child ATD positioned in the rear, far-side seating location. Data from nine side impact sled tests simulating a EuroNCAP AEMD barrier test were analyzed with data obtained from 44 side impact crash tests. The crash tests included: FMVSS 214 and IIHS MDB, moving car-to-stationary car and moving car-to-moving car. A Q6 or prototype Q6s ATD was seated on the far-side, using a variety of low and high back booster seats. Head and chest responses were recorded and ATD motions were tracked with high-speed videos. The vehicle lateral accelerations resulting from MDB tests were characterized by a much earlier and more rapid rise to peak than in tests where the bullet was another car.

The responses of a 5th percentile female ATD in the driver and/or rear passenger positions of 56 crashes are described. The Transport Canada side impact programme consisted of LTV-to-car impacts, car-to-car impacts and IIHS barrier-to-car tests. The majority of the tests involved severe crash conditions for which the vehicles were not designed. The SID-IIs head, chest and abdominal responses were compared to determine the effects of the striking bullet geometry, the angle of impact, the impact point and the self-protective elements of the struck vehicle, including airbag technology and armrest designs. The SID-IIs head responses and deflection measures were sufficiently sensitive to discriminate between the various striking vehicles, crash configurations, airbag systems and armrest characteristics.

Two manufacturers, Denton ATD and FTSS, currently produce the Hybrid III 5th percentile female dummy. In response to concerns raised by industry that differences in the anthropometry of the molded breasts between the two manufacturers may influence chest responses, Transport Canada conducted a comparative testing program. Thorax biofidelity tests were conducted to compare force-deflection characteristics; full-frontal, rigid-barrier tests were conducted at 40, 48 and 56 km/h to compare chest responses, and out-of-position chest on module static airbag deployment tests were conducted to compare peak chest deflections of the Denton and FTSS dummy jackets and of a prototype jacket without breasts. Differences in force-deflection characteristics were observed during biofidelity pendulum impacts of the two dummies, with much of the differences attributed to the different chest jackets.