Search Results

Automobile brake squeal has been experimentally studied in many ways over the past 65 years. A large body of published research and a substantial amount of unpublished work have attempted to experimentally define the variables involved with and describe the system dynamics initiating the friction-induced self-excited vibration. Much of this work has centered on pin on disk type test rigs used to characterize the contact mechanics and/or friction laws without considering the brake system influence. This paper describes a dynamometer designed and constructed to study brake squeal on a system level.

A proposed multi-coordinate spectral-based inverse substructuring approach is applied experimentally to examine the vibration transmissibility through chassis mounts. In this formulation, the vehicle system is partitioned into two substructures. One substructure comprises of the chassis and suspension, while the second one is the body structure and other attached components. The approach yields the free substructure dynamic characteristics that are extracted from the measured coupled system response spectra. The resultant free substructure transfer functions are verified by comparison of the re-synthesized results to the actual vehicle system measurements. A real life vehicle setup is utilized to demonstrate the salient features and capabilities of this approach, which includes the ability to compute the main structure-borne paths, dynamic interactions between the chassis and body, and interior noise and vibration response.

Sound transmission through the sidewall of an automotive muffler has been studied theoretically and experimentally. Three wall structures: a single shell, double shell and porous-cored shell constructions are considered. Transmission losses through the sidewalls were measured using the two microphone method. Experimental results are compared to one another, and to the corresponding theoretical analysis results, which shows that the mean flow effect is not a significant factor in designing the muffler sidewall.

A multi-coordinate FRF-based inverse substructuring approach is proposed to partition a vehicle system into two or more substructures, which are coupled at discrete interface points. The joint and free substructure dynamic characteristics are then extracted from the coupled system response spectra. Depending on the actual form of the structural coupling terms, three forms of the coupling matrix are assumed here. The most general one constitutes the non-diagonal form, and the other two simpler cases are the block-diagonal and purely diagonal representations that can be used to simplify testing process and overcome computational problems. The paper is focused on the investigation of the durability of these three formulations when the input FRFs are noise contaminated. A finite element model of a simplified vehicle system is used as the case study.

A spectral-based substructuring approach applying linear frequency response functions (FRF) is proposed for improving the accuracy of simulating the dynamics of coupled systems. The method also applies a least square singular value decomposition (SVD) scheme to overcome the inherent computational deficiency in the basic substructuring formulation. The computational problem is caused by the magnification of measurement errors during any one of the matrix inversion calculations required for this method. The primary objective of applying this approach is to examine the possibility of analyzing higher frequency response that is normally not possible using conventional modeling technique such as the direct finite and boundary element, and lumped parameter techniques. In this study, additional concepts are also evaluated to quantify the limitations and range of applicability of the proposed substructuring approach for simulating the vibration response of complex powertrain structures.

This paper is intended to describe some of the advances in automotive NVH research and applications based on recent developments in the Structural Dynamics Research Laboratory (SDRL) at the University of Cincinnati. State-of-the-art vibro-acoustic research capabilities and infrastructure ranging from advanced vibration modal analysis and spectral techniques for linear and nonlinear automotive systems to computational tools for structure-borne acoustic noise generation, transmission and synthesis problems are discussed. These systems have been devised with the intent of integrating a versatile set of experimental, computational and analytical approaches in order to be able to investigate a variety of crucial automotive NVH concerns. The materials will be grouped into three separate but closely related sets of applications consisting of (i) powertrain noise and vibration control, (ii) analysis and control vehicle system dynamics, and (iii) NVH and sound quality.

Active noise control systems have been gaining popularity in the last couple of decades, due to the deficiencies in passive noise abatement techniques. In the future, a novel combination of passive and active noise control techniques may be applied more widely, to better control the interior sound quality of vehicles. In order to maximize the effectiveness of this combined approach, smarter algorithms will be needed for active noise control systems. These algorithms will have to be computationally efficient, with high stability and convergence rates. This will be necessary in order to accurately predict and control the interior noise response of a vehicle. In this study, a critical review of the filtered-x least mean square (FXLMS) algorithm and several other newly proposed algorithms for the active control of vehicle powertrain noise, is performed. The analysis examines the salient features of each algorithm, and compares their system performance.

An enhanced, frequency domain filtered-x least mean square (LMS) algorithm is proposed as the basis for an active control system for treating powertrain noise. There are primarily three advantages of this approach: (i) saving of computing time especially for long controller’s filter length; (ii) more accurate estimation of the gradient due to the sample averaging of the whole data block; and (iii) capacity for rapid convergence when the adaptation parameter is correctly adjusted for each frequency bin. Unlike traditional active noise control techniques for suppressing response, the proposed frequency domain FXLMS algorithm is targeted at tuning vehicle interior response in order to achieve a desirable sound quality. The proposed control algorithm is studied numerically by applying the analysis to treat vehicle interior noise represented by either measured or predicted cavity acoustic transfer functions.

Demand for accurate and reliable gamma dosimetry in a radiation environment and the unsatisfactory performance of the existing devices has given rise to the need for a better gamma measurement system, capable of operating in a high dose rate environment and withstanding a high total dose. The concept of a new gamma dose measurement device based on the principle of photoconductivity has the potential of filling this void. Preliminary experiments and analyses indicated that the selected dosimeter materials exhibit photoconductivity in a useful range, responsive to changes in gamma dose rate. The initial Pyrex glass dosimeter appeared to suffer radiation damage at the relatively high dose rates employed (up to 0.116 Mega rads/hour). Quartz is now being studied as an alternative material.

The goal of the presented research is to study the effective operational range for a centrifugal vaneless diffuser turbocharger compressor with ported shroud typically used in diesel engines. A turbocharger bench facility was designed and tested in order to define the performances of the compressor and to better understand the occurrence of instabilities in the housing. Specific emphasis was given to the low mass flow rate region of the compressor performance characteristics where instabilities occur with fluctuations that can be significantly large in the case of surge. Static pressures and dynamic pressure fluctuations were measured at the inlet, the outlet, as well as at different positions around the volute and diffuser sections of the compressor in order to assess the development and propagation of flow instabilities. The dynamic signature of the flow was measured along with the elaboration of the compressor mapping.

The prediction and control of gear vibration and noise has become very important in the design of a quiet, high-quality gearbox systems. The vibratory energy of the gear pair caused by transmission error excitation is transmitted structurally through shaft-bearing-housing assembly and radiates off from exterior housing surface. Most of the previous studies ignore the contribution of components flexibility to the transmission error (TE) and system dynamic responses. In this study, a system level model of axle system with hypoid gear pair is developed, aiming at investigating the effect of the elasticity of the shafts, bearings and housing on TE as well as the contribution of flexible bearings on the dynamic responses. The load distribution results and gear transmission errors are calculated and compared between different assumptions on the boundary conditions.

Actuator and roller screw mechanism are key components of electromechanical brake (EMB) system in automotive and aerospace industry. The inverted planetary roller screw mechanism (IPRSM) is particularly competitive due to its high load-carrying capacity and small assembly size. For such systems, friction characteristic and friction torque generated from rolling/sliding contacts can be an important factor that affects the dynamic performance as well as vibration behavior. This paper investigates the modeling and simulation of the EMB system in early design stage with special attention to friction torque modelling of IPRSM. Firstly, a step-by-step system model development is established, which includes the controller, servo motor, planetary gear train and roller screw mechanism to describe the dynamic behavior of the EMB system.

Order based torsional vibration analysis codes require a separate, non-linear model to compute single cylinder excitation torque for input. The slider crank mechanism model is typically derived using a crankshaft constant angular velocity assumption. Additionally, the equation describing this constant speed mechanism is derived in an approximate form. An exact model for the slider crank mechanism turning at non-constant speed is used in an iterative procedure with an order based impedance model torsional analysis code to quantify the effects of these assumptions. Results are presented for an in-line six diesel engine, and generalized where possible.

Test sensors are evaluated for noise path analysis applications. Newly developed ICP™ piezo-electric strain gages are used with accelerometers and microphones in a conventional noise path analysis test on the front body/suspension attachment points of a vehicle. In a less conventional application, a steering knuckle is converted into a 6-DOF force transducer using an array of strain gages and using an array of 3-DOF load cells. The two sensor arrays are both calibrated with a 6-DOF load cell. The result is an estimate of the three translation force and three moment operating inputs entering the steering knuckle from the wheel.

This paper describes an active sound tuning (AST) system for vehicle powertrain response. Instead of simply aiming to attenuate cabin interior noise, AST system is capable of reshaping the powertrain response based on predetermined vehicle sound quality criteria. However, conventional AST systems cannot yield a balanced result over the broad frequency range when applied to powertrain noise. It is due to the fact that existing systems are typically configured with the filtered-x least mean square (FXLMS) algorithm or its modified versions, which has inherent frequency dependent convergence behavior due to large dynamic range of secondary path (the electro-acoustic path from the control speaker to the error microphone). Therefore, fast convergence can only be reached at the resonant frequencies.

Cycloid drives are widely used in the in-wheel motor for electric vehicles due to the advantages of large ratio, compact size and light weight. To improve the transmission efficiency and the load capability and reduce the manufacturing cost, a novel cycloid drive with non-pin design for the application in the in-wheel motor is proposed. Firstly, the generation of the gear pair is presented based on the gearing of theory. Secondly, the meshing characteristics, such as the contact zones, curvature difference, contact ratio and sliding coefficients are derived for performance evaluation. Then, the loaded tooth contact analysis (LTCA) is performed by establishing a mathematical model based on the Hertz contact theory to calculate the contact stress and deformation.

The noise and vibration response of hypoid or bevel geared rotor system, primarily excited by transmission error (TE), and mesh vector and stiffness variations, can be affected significantly by the coupling between the driveline rotor dynamics and gear vibratory response. This is because of the inherent design comprising of non-parallel rotational axes and time-varying as well as spatial-varying gear mesh characteristics. One of the important factors of the driveline system dynamics is the rotor gyroscopic effect that has not been studied extensively in traditional gear dynamics. To address this gap in the literature, this paper attempts to examine the influence of incorporating gyroscopic terms in the hypoid gear dynamic simulation. A multi-degrees-of-freedom, multi-body dynamic model is used as a generalized representation of a hypoid geared rotor system.

Current powertrain active noise control (ANC) systems are not sufficient enough to track the fast engine speed variations, and yield consistent convergence speeds for individual engine order such that a balanced noise reduction performance can be achieved over a broad frequency range. This is because most of these ANC systems are configured with the standard filtered-x least mean squares (FxLMS) algorithm, which has an inherent limitation in the frequency-dependent convergence behavior due to the existence of secondary path model (electro-acoustic path from the input of control loudspeaker to the output of monitoring error microphone) in the reference signal path. In this paper, an overview is given first to compare several recently modified FxLMS algorithms to improve the convergence speed for harmonic responses such as eigenvalue equalization FxLMS (EE-FXLMS) and normalized reference LMS (NX-LMS) algorithms.

A multi-point hypoid gear mesh model based on 3-dimensional loaded tooth contact analysis is incorporated into a coupled multi-body dynamic and vibration hypoid gear model to predict more detailed dynamic behavior of each tooth pair. To validate the accuracy of the proposed model, the time-averaged mesh parameters are applied to linear time-invariant (LTI) analysis and the dynamic responses, such as dynamic mesh force, dynamic transmission error, are computed, which demonstrates good agreement with that predicted by single-point mesh model. Furthermore, a nonlinear time-varying (NLTV) dynamic analysis is performed considering the effect of backlash nonlinearity and time-varying mesh parameters, such as mesh stiffness, transmission error, mesh point and line-of-action. Simulation results show that the time history of the mesh parameters and dynamic mesh force for each pair of teeth within a full engagement cycle can be simulated.

Turbochargers are commonly used in automotive engines to increase the internal combustion engine performance during off design operation conditions. When used, a most wide operation range for the turbocharger is desired, which is limited on the compressor side by the choke condition and the surge phenomenon. The ported shroud technology is used to extend the operable working range of the compressor, which permits flow disturbances that block the blade passage to escape and stream back through the shroud cavity to the compressor inlet. The impact of this technology on a speed-line at near optimal operation condition and near surge operation condition is investigated. A numerical study investigating the flow-field in a centrifugal compressor of an automotive turbocharger has been performed using Large Eddy Simulation. The wheel rotation is handled by the numerically expensive sliding mesh technique. In this analysis, the full compressor geometry (360 deg) is considered.