Search Results

Vehicle safety systems may use occupant physiological information, e.g., occupant heights and weights to further enhance occupant safety. Determining occupant physiological information in a vehicle, however, is a challenging problem due to variations in pose, lighting conditions and background complexity. In this paper, a novel occupant height estimation approach is presented. Depth information from a depth camera, e.g., Microsoft Kinect is used. In this 3D approach, first, human body and frontal face views (restricted by the Pitch and Roll values in the pose estimation) based on RGB and depth information are detected. Next, the eye location (2D coordinates) is detected from frontal facial views by Haar-cascade detectors. The eye-location co-ordinates are then transferred into vehicle co-ordinates, and seated occupant eye height is estimated according to similar triangles and fields of view of Kinect.

Due to the variation of compartment design and occupant’s posture in self-driving cars, there is a new and major challenge for occupant protection. In particular, the studies on occupant restraint systems used in the self-driving car have been significantly delayed compared to the development of the autonomous technologies. In this paper, a numerical study was conducted to investigate the effectiveness of three typical restraint systems on the driver protection in three different scenarios.

Accident statistics have shown that older and obese occupants are less adaptable to existing vehicle occupant restraint systems than ordinary middle-aged male occupants, and tend to have higher injury risk in vehicle crashes. However, the current research on injury mechanism of aging and obese occupants in vehicle frontal impacts is scarce. This paper focuses on the optimization design method of occupant restraint system parameters for specific body type characteristics. Three parameters, namely the force limit value of the force limiter in the seat belt, pretensioner preload of the seat belt and the proportionality coefficient of mass flow rate of the inflator were used for optimization. The objective was to minimize the injury risk probability subjected to constraints of occupant injury indicator values for various body regions as specified in US-NCAP frontal impact tests requirements.

An autonomous emergency braking (AEB) system can detect emergency conditions using sensors (e.g., radar and camera) to automatically activate the braking actuator without driver input. However, during the hard braking phase, crash conditions for the restraint system can easily change (e.g., vehicle velocity and occupant position), causing an out-of-position (OOP) phenomenon, especially for unbelted occupants entering the airbag deployment range, which may lead to more severe injuries than in a normal position. A critical step in reducing the injury of unbelted occupants would be to design an AEB system while considering the effect of deployed airbags on the occupants. Thus far, few studies have paid attention to the compatibility between AEB and airbag systems for unbelted occupants. This study aims to provide a method that combines AEB and airbag systems to explore the potential injury reduction capabilities for unbelted occupants.

The handling of flexible components creates a unique problem set for pick and place automation within automotive production processes. Fabrics and woven textiles are examples of flexible components used in car interiors, for air bags, as liners and in carbon-fiber layups. These textiles differ greatly in geometry, featuring complex shapes and internal slits with varying material properties such as drape characteristics, crimp resistance, friction, and fiber weave. Being inherently flexible and deformable makes these materials difficult to handle with traditional rigid grippers. Current solutions employ adhesive, needle-based, and suction strategies, yet these systems prove a higher risk of leaving residue on the material, damaging the weave, or requiring complex assemblies. Pincer-style grippers are suitable for rigid components and offer strong gripping forces, yet inadvertently may damage the fabric, and introduce wrinkles / folded-over edges during the release process.

Human tolerance to knee, chest, and head impacts based upon skeletal fracture of cadavers is reported. The results are based upon unrestrained cadaver impacts in a normal seated position in simulated frontal force accidents at velocities between 10 and 20 mph and stopping distances of 6-8 in. The head target was covered with 15/16 in. of padding. No skull or facial fractures were observed at loads up to 2640 lb. Extensive facial fractures and a linear skull fracture occurred during the application of the maximum head force of 4350 lb. The chest target was 6 in. in diameter with 15/16 in.of padding. The padding was rolled over the edge of the target to minimize localized high force areas on the ribs. A 1/8 in. diameter rod was inserted through the chest and fastened through a ball joint and flange to the soft tissue at the sternum.

An understanding of stiffness characteristics of different body regions, such as thorax, abdomen and pelvis of ES-2re and SID-IIs dummies under controlled laboratory test conditions is essential for development of both compatible performance targets for countermeasures and occupant protection strategies to meet the recently updated FMVSS214, LINCAP and IIHS Dynamic Side Impact Test requirements. The primary purpose of this study is to determine the transfer functions between the ES-2re and SID-IIs dummies for different body regions under identical test conditions using flat rigid wall sled tests. The experimental set-up consists of a flat rigid wall with five instrumented load-wall plates aligned with dummy’s shoulder, thorax, abdomen, pelvis and femur/knee impacting a stationary dummy seated on a rigid low friction seat at a pre-determined velocity.

Previous study suggested that female, thin, obese, and older occupants had a higher risk of death and serious injury in motor vehicle crashes. Human body finite element models were a valuable tool in the study of injury biomechanics. The mesh deformation method based on radial basis function(RBF) was an attractive alternative for morphing baseline model to target models. Generally, when a complex model contained many elements and nodes, it was impossible to use all surface nodes as landmarks in RBF interpolation process, due to its prohibitive computational cost. To improve the efficiency, the current technique was to averagely select a set of nodes as landmarks from all surface nodes. In fact, the location and the number of selected landmarks had an important effect on the accuracy of mesh deformation. Hence, how to select important nodes as landmarks was a significant issue. In the paper, an efficient peak point-selection RBF mesh deformation method was used to select landmarks.

The biodynamic response of the femur during passively restrained -Gx impact acceleration is reported in this paper. Eleven unembalmed cadavers, ranging in age from 21 to 65 and weighing from 50 to 96 kg, were tested in a VW Rabbit seat with a passive belt and knee restraint. Sectioned parts of the VW knee bolster were placed about 130 mm away from the patella at the initiation of the tests. The height of the knee bolsters was adjusted individually in the eleven tests. Ten were set for loading directly through the patella. In one run, the impact was below the knee joint. The sectioned bolsters were mounted on a rigid frame and instrumented with triaxial load cells. A six-axis load cell was installed in the right femur. Photo targets were attached directly to the femur and tibia. Sled runs were made at 22 and 35 g. Only one cadaver sustained bilateral femoral fractures at 35 g.

It is shown that the response of the occiput of a cadaver to sinusoidal vibration input to the frontal bone corresponds closely to that of a simple damped spring-mass system having a natural frequency equal to the first mode frequency of the skull, 0.17 damping factor. The first and third bending mode of the skull occurred near 300 and 900 Hz for both the cadaver preparation with silicon gel filled cranial cavity and the live human head. A second mode was found near 600 Hz in the live human. Head acceleration levels at which opposite pole pressure reached near —1 atm were 170 g and 500–600 g in the human cadaver and live monkey head, respectively, which values are roughly inversely proportional to major intracranial diameters. A method is derived for comparing the impact response of a simple system to a general shaped pulse to that of the cadaver head.

A review of the existing mathematical models of a car occupant in a rear-end crash reveals that existing models inadequately describe the kinematics of the occupant and cannot demonstrate the injury mechanisms involved. Most models concentrate on head and neck motion and have neglected to study the interaction of the occupant with the seat back, seat cushion, and restraint systems. Major deficiencies are the inability to simulate the torso sliding up the seat back and the absence of the thoracic and lumbar spine as deformable, load transmitting members. The paper shows the results of a 78 degree-of-freedom model of the spine, head, and pelvis which has already been validated in +Gz and -Gx acceleration directions. It considers automotive-type restraint systems, seat back, and seat cushions, and the torso is free to slide up the seat back.

Impacts have been analyzed in terms of degree of injury, head injury criterion (HIC), and average acceleration as a function of time for frontal impacts against the following surfaces: 1. Rigid flat surface-fractured cadaver skull. 2. Astroturf-head drop of football-helmeted cadaver. 3. Windshield penetrating impact of a dummy. 4. Airbag-dynamic test by human volunteers. It is concluded that the linear acceleration/time concussion tolerance curve may not exist and that only impacts against relatively stiff surfaces producing impulses with short rise times can be critical. The authors hypothesize that if a head impact does not contain a critical HIC interval of less than 0.015 s, it should be considered safe as far as cerebral concussion is concerned.

A plethora of applications in the transportation industry for both vehicular and roadside safety hardware, especially seatbelts, harnesses and restraints, rely on tensile loading to dissipate energy and minimize injury. There are disadvantages to the current state-of-the-art for these tensile energy absorbers, including erratic force-displacement responses and low tensile force efficiencies (TFE). Axial cutting was extensively demonstrated by researchers at the University of Windsor to maintain a stable reaction force, although exclusively under compressive loading. A novel apparatus was investigated in this study which utilized axial cutting under a tensile loading condition to absorb energy. A parametric scope was chosen to include circular AA6061 extrusions in both T4 and T6 temper conditions with an outer diameter of 63.5 mm and wall thickness of 3.18 mm.

The seatbelt system, originally designed for protecting occupants in frontal crashes, has been reported to be inadequate for preventing occupant head-to-roof contact during rollover crashes. To improve the effectiveness of seatbelt systems in rollovers, in this study, we reviewed previous literature and proposed vertical head excursion corridors during static inversion and dynamic rolling tests for human and Hybrid III dummy. Finite element models of a human and a dummy were integrated with restraint system models and validated against the proposed test corridors. Simulations were then conducted to investigate the effects of varying design factors for a three-point seatbelt on vertical head excursions of the occupant during rollovers. It was found that there were two contributing parts of vertical head excursions during dynamic rolling conditions.

A test program has been conducted to determine the fracture behavior of the human frontal bone against two different rigid cylindrical surfaces; one surface was of 1 in. radius and one was of 5/16 in. radius; both were 6½ in. long. The purpose of this research program was to provide human tolerance data which would: 1. Assist in the design of structures likely to be impacted by the human head. 2. Extend the calibration range of frangible headforms. Twelve cadavers were tested in this program; seven against the 1 in. radius cylinder and five against the 5/16 in. radius cylinder. The test arrangement employed a guided drop of the test surface against a stationary head which was free to rebound. Drop heights were increased progressively until borderline fractures were obtained. The large radius shape consistently yielded linear fractures indicating that it is effectively a blunt surface. Fracture loads ranged 950-1650 lb.

Currently, there is great interest in motorsports medicine in measuring driver head impact accelerations by adding small triaxial accelerometers to the communication earpieces worn by drivers. Various studies have attempted to validate the ability of the earpiece accelerometers to accurately measure head accelerations. Those experiments demonstrate success in being able to measure head accelerations on dummies and humans in low severity impacts and non-impact head motion. No study has been performed to ascertain the ability of the earpiece accelerometers to accurately measure rigid body head accelerations of the skull when they are mounted in a human ear canal and subjected to high severity head accelerations. This research was performed to evaluate the frequency response and coupling of the earpiece accelerometers to the human skull using post mortem human subject (PMHS) heads as the most realistic surrogate for the living human.

A human head model has been developed primarily for use in evaluation of impact attenuation properties of football helmets, but is also applicable in automobile impact safety tests. Using firm silicon rubber molds made from impressions of cadaver bones, a skull and mandible were each cast in one piece using a self-skinning urethane foam that hardens into cross section geometry similar to the human bone. A rubber gel material is used to simulate the brain. The skull and attached mandible are overlayed with repairable silicon rubber skin having puncture and sliding-over-bone characteristics similar to human skin. At present, the model has a rudimentary solid silicon rubber neck, through the center of which runs a flexible steel cable attached at the foramen magnum. The cable is used to attach the head to a carriage or anthropometric dummy and can be adjusted in tension to give various degrees of flexibility.

A comparison is presented of the forces, accelerations, and kinematics of an anthropomorphic dummy for identical sled impacts for unrestrained, lap belted, and lap and diagonal chest restrained conditions. Biaxial accelerometers were mounted in the head, chest, and on the proximal end of the femur to obtain the accelerations during the impacts. Seat belt load cells were put in series with the belts at each anchor point. Biaxial load cells were positioned to be impacted by the head, chest, and each knee for the unrestrained condition and by the head and chest for the lap belted configuration. For the lap and diagonal chest restrained condition these load cells were not used. Impacts of 10 and 20 miles per hour were made with sled stopping distance of 4 and 9 inches, respectively. At 20 miles per hour the head struck with a force of 1580 pounds in the unrestrained mode, 600 pounds with the lap belt, and did not hit with the lap and shoulder harness.

This research focuses on the further development of a child finite element model whereby implementation of pediatric cadaver testing observations considering the biomechanical response of the neck of children under tensile and bending loading has occurred. Prior to this investigation, the biomechanical neck response was based upon scaled adult cadaver behaviour. Alterations to the material properties associated with ligaments, intervertebral discs and facet joints of the pediatric cervical spine were considered. No alteration to the geometry of the child neck finite element model was considered. An energy based approach was utilized to provide indication on the appropriate changes to local neck biomechanical characteristics. Prior to this study, the biomechanical response of the neck of the child finite element model deviated significantly from the tensile and bending cadaver tests completed by Ouyang et al.

This research focuses on comparing the biomechanical response of the head and neck of the Hybrid III 3-year-old anthropometric test device finite element model and pediatric cadaver data, under flexion-extension bending and axial tensile loading conditions. Previous experimental research characterized the quasi-static biomechanical response of the pediatric cervical spine under flexion-extension bending and tolerance in tensile distraction loading conditions. Significant differences in rotational and linear stiffness were found between the Hybrid III model and the pediatric cadaver data. In this research the biomechanical child cadaver neck response has been implemented into the 3-year-old Hybrid III child dummy FE model. An explicit finite element code (LS-DYNA) and the modified Hybrid III model were used to numerically simulate the previous cadaver tests and validate the altered Hybrid III neck.