Search Results

The European Commission has released strict emission regulations for passenger cars in the past decade in order to improve air quality in cities and limit harmful emission exposure to humans. In the near future, even stricter regulations containing more realistic/demanding driving scenarios and covering more exhaust gas components are expected to be released. Passenger cars fueled with gasoline are one contributor to unhealthy air conditions, due to the fact that gasoline engines emit harmful air pollutants. One option to minimize harmful emissions would be to utilize specifically tailored, low emission synthetic fuels or fuel blends in internal combustion engines. Methyl formate and dimethyl carbonate are two promising candidates to replace or substitute gasoline, which in previous studies have proven to significantly decrease harmful pollutants.

Improving fuel efficiency while meeting relevant emission limits set by emissions legislation is among the main objectives of engine development. Simultaneously the development costs and development time have to be steadily reduced. For these reasons, the high demands in terms of quality and validity of measurements at the engine test bench are continuously rising. This paper will present a new methodology for efficient testing of an industrial combustion engine in order to improve the process of decision making for combustion-relevant component setups. The methodology includes various modules for increasing measurement quality and validity. Modules like stationary point detection to determine steady state engine behavior, signal quality checks to monitor the signal quality of chosen measurement signals and plausibility checks to evaluate physical relations between several measurement signals ensure a high measurement quality over all measurements.

Presented within the framework of this SAE Technical Paper are the highly accurate results of friction experiments, performed upon a floating-liner, single-cylinder test engine with a capacity 0.5 liters and crank angle resolution during motored and fired operation. This allows for the measurement of mixed friction zones at the dead centers. These mixed friction zones can result in friction losses and lead to wear in the components in-volved. The strength of the friction forces in any given mixed friction zone is largely dependent on the operating point. This is why the influence of each of the most important operating parameters - speed (rpm), load, oil and coolant temperature - is individually analysed, before the interactions, which are depicted in the resultant engine map, are discussed.

Synthetic fuels for internal combustion engines offer CO2-neutral mobility if produced in a closed carbon cycle using renewable energies. C1-based synthetic fuels can offer high knock resistance as well as soot free combustion due to their molecular structure containing oxygen and no direct C-C bonds. Such fuels as, for example, dimethyl carbonate (DMC) and methyl formate (MeFo) have great potential to replace gasoline in spark-ignition (SI) engines. In this study, a mixture of 65% DMC and 35% MeFo (C65F35) was used in a single-cylinder research engine to determine friction losses in the piston group using the floating-liner method. The results were benchmarked against gasoline (G100). Compared to gasoline, the density of C65F35 is almost 40% higher, but its mass-based lower heating value (LHV) is 2.8 times lower. Hence, more fuel must be injected to reach the same engine load as in a conventional gasoline engine, leading to an increased cooling effect.

This SAE Technical Paper contains detailed data which are relevant for the calculation of the friction forces of the piston assembly in internal combustion engines. Useful ways of employing calculations besides measurements are exactly classified for the optimization of the piston assembly system in order to reduce friction losses. In the first step the theoretical basics for the calculation of the tribological system are introduced. Referring to the theory, the paper goes into detail about the basic set-up and the modeling degree of the calculation program. Furthermore, measured and calculated curves of friction forces are compared for different operating points. In addition, analysis of the crank-angle resolved friction force are presented with varying engine speeds, oil temperatures and loads and a detailed interpretation of the results is given.

A new constant volume combustion chamber (CVCC) apparatus is presented that calculates the cetane number (CN) of fuels from their ignition delay by means of a primary reference fuel calibration. It offers the benefits of low fuel consumption, suitability for non-lubricating substances, accurate and fast measurements and a calibration by primary reference fuels (PRF). The injection system is derived from a modern common-rail passenger car engine. The apparatus is capable of fuel injection pressures up to 1200 bar and requires only 40 ml of the test fuel. The constant volume combustion chamber can be heated up to 1000 K and pressurized up to 50 bar. Sample selection is fully automated for independent operation and low levels of operator involvement. Capillary tubes employed in the sampling system can be heated to allow the measurement of highly viscous fuels.

On the way to a climate-neutral mobility, synthetic fuels with their potential of CO2-neutral production are currently in the focus of internal combustion research. In this study, the C1-fuels methanol (MeOH), dimethyl carbonate (DMC), and methyl formate (MeFo) are tested as pure fuel mixtures and as blend components for gasoline. The study was performed on a single-cylinder engine in two configurations, thermodynamic and optical. As pure C1-fuels, the previously investigated DMC/MeFo mixture is compared with a mixture of MeOH/MeFo. DMC is replaced by MeOH because of its benefits regarding laminar flame speed, ignition limits and production costs. MeOH/MeFo offers favorable particle number (PN) emissions at a cooling water temperature of 40 °C and in high load operating points. However, a slight increase of NOx emissions related to DMC/MeFo was observed. Both mixtures show no sensitivity in PN emissions for rich combustions. This was also verified with help of the optical engine.

In the present work the benefit of a 50 MPa gasoline direct injection system (GDI) in terms of particle number (PN) emissions as well as fuel consumption is shown on a 0.5 l single cylinder research engine in different engine operating conditions. The investigations show a strong effect of injection timing on combustion duration. As fast combustion can be helpful to reduce fuel consumption, this effect should be investigated more in detail. Subsequent analysis with the method of particle image velocimetry (PIV) at the optical configuration of this engine and three dimensional (3D) computational fluid dynamics (CFD) calculations reveal the influence of injection timing on large scale charge motion (tumble) and the level of turbulent kinetic energy. Especially with delayed injection timing, high combustion velocities can be achieved. At current series injection pressures, the particle number emissions increase at late injection timing.

The development of today's powertrains focuses on the reduction of CO₂ emissions. Therefore several new technologies for internal combustion engines have been established. A further tendency is the successive electrification of powertrains in hybrid vehicles. However, these trends lead to increasing system costs which are a very important aspect at the market segment of compact cars. At the Institute of Internal Combustion Engines of the Technical University of Munich a drivetrain concept for urban and commuter traffic is under development. It is based on a lean-burn air-cooled two-cylinder natural gas engine which is combined with a hydraulic hybrid system. The paper contains detailed information about the engine as well as the hybrid vehicle powertrain in parallel structure. Particular characteristics and innovations of the hydraulic hybrid system compared to systems known so far are shown.

Polyoxymethylene dimethyl ethers (OME) are promising alternative diesel fuels with a biogenic or electricity-based production, which offer carbon neutral mobility with internal combustion engines. Among other e-fuels, they stand out because of soot-free combustion, which resolves the trade-off between nitrogen oxide (NOx) and soot emissions. Additionally, long-chain OME have a high ignitability, indicated by a cetane number (CN) greater than 70. This opens up degrees of freedom in the injection strategy and enables simplifications compared to the operation with fossil diesel. This study investigates the hydraulic behavior of two solenoid injectors with different injector geometry for heavy-duty applications on an Injection Rate Analyzer (IRA) in diesel and OME operation. For OME, both injectors show longer injection delays in all injection pressure ranges investigated, increasing with rail pressure.

Natural gas and especially biogas combustion can be seen as one of the key technologies towards climate-neutral energy supply. With its extensive availability, biogas is amongst the most important renewable energy sources in the present energy mix. Today, the use of gaseous fuels is widely established, for example in cogeneration units for combined heat and power generation. In contrast to conventional spark plug ignition, the combustion can also be initialized by a pilot injection. In order to further increase engine efficiency, this article describes the process for a targeted optimization of the pilot fuel injection. One of the crucial points for a more efficient dual fuel combustion process, is to optimize the amount of pilot injection in order to increase overall engine efficiency, and therefore decrease fuel consumption. In this connection, the injection system plays a key role.

Hybridization is a promising way to further reduce the CO2 emissions of passenger vehicles. However, high engine efficiencies and the reduction of engine load, due to torque assists by an electric motor, cause a decrease of exhaust gas temperature levels. This leads to an increased time to catalyst light-off, resulting in an overall lower efficiency of the exhaust aftertreatment system (ATS). Especially in low load driving conditions, at cold ambient temperatures and on short distance drives, the tailpipe pollutant emissions are severely impacted by these low ATS efficiency levels. To ensure lowest emissions under all driving conditions, catalyst heating methods must be used. In conventional vehicles, internal combustion engine measures (e.g. usage of a dedicated combustion mode for late combustion) can be applied. A hybrid system with an electrically heated catalyst (EHC) enables further methods such as the increase of engine load by the electric motor or electric catalyst heating.

Polyoxymethylene dimethyl ethers (OME) are synthetic fuels, which offer the property of sustainability because the reactants of production base on hydrogen and carbon dioxide on the one hand, and the air pollution control in consequence of a soot-free combustion in a diesel engine on the other hand. High exhaust gas recirculation (EGR) rates are a promising measure for nitrogen oxide (NOx) reduction without increasing particle emissions because of the resolved soot-NOx trade-off. However, EGR rates towards stoichiometric combustion in OME operation reveals other trade-offs such as methane and formaldehyde emissions. To avoid these, a lean mixture with a combination of EGR and exhaust after-treatment with selective catalytic reduction (SCR) is useful. The limitation of urea dosing due to the light-off temperature of SCR systems requires heating measures.

In the near future, pollutant and GHG emission regulations in the transport sector will become increasingly stringent. For this reason, there are many studies in the field of internal combustion research that investigate alternative fuels, one example being oxygenated fuels. Additionally, the design of engine components needs to be optimized to improve the thresholds of clean combustion and thus reduce particulates. Simulations based on PRiME 3D® for dynamic behaviors inside the piston ring group provide a guideline for experimental investigation. Gas flows into the combustion chamber are controlled by adjusting the piston ring design. A direct comparison of regular and synthetic fuels enables to separate the emissions caused by oil and fuel. This study employed a mixture of dimethyl carbonate (DMC) and methyl formate (MeFo).

Oxygenated synthetic fuels such as oxymethylene ether (OME) are a promising approach to reduce the emissions of diesel engines and to improve sustainability of mobility. The soot-free combustion of OME allows an optimization of the combustion process to minimize remaining pollutants. Considering the injection system, one strategy is to decrease the rail pressure, which has a positive impact on the reduction of nitrogen oxides without increasing the particle formation. Furthermore, due to the reduced lower heating value of OME compared to diesel fuel, an adaptation of the injector nozzle is recommended. This work describes a method for analyzing the injection process for OME, using the Mie scattering effect in an optically accessible heavy-duty diesel engine. The design of the 1.75 l single cylinder engine allows operation up to 300 bar peak cylinder pressure, providing optical access through the piston bowl and through a second window lateral below the cylinder head.

Scarce resources of fossil fuels and increasingly stringent exhaust emission legislation push towards a stronger focus to alternative fuels. Natural gas is considered a promising solution for small engines and passenger cars due to its high availability and low carbon dioxide emissions. Furthermore, natural gas indicates great potential of increased engine efficiency at lean-burn operation. However, the ignition of these lean air/fuel mixtures leads to new challenges, which can be met by fuel scavenged prechambers. At the Institute of Internal Combustion Engines of the Technische Universitaet Muenchen an air cooled natural gas engine with a single cylinder displacement volume of 0.5 L is equipped with a methane scavenged prechamber for investigations of the combustion process under real engine conditions. The main combustion chamber is supplied with a lean premixed air/fuel mixture.

Over the past years, the question as to what may be the powertrain of the future has become ever more apparent. Aiming to improve upon a given technology, the internal combustion engine still offers a number of development paths in order to maintain its position in public and private mobility. In this study, an innovative combustion process is investigated with the goal to further approximate the ideal Otto cycle. Thus far, similar approaches such as Homogeneous Charge Compression Ignition (HCCI) shared the same objective yet were unable to be operated under high load conditions. Highly increased control efforts and excessive mechanical stress on the components are but a few examples of the drawbacks associated with HCCI. The approach employed in this work is the so-called Spark Assisted Compression Ignition (SACI) in combination with a pre-chamber spark plug, enabling short combustion durations even at high dilution levels.

Diesel engines are arguably the superior device in the ground transportation sector in terms of efficiency and reliability, but suffer from inferior emission performance due to the diffusive nature of diesel combustion. Great research efforts gradually reduced nitrogen oxide (NOX) and particulate matter (PM) emissions, but the PM-NOX trade-off remained to be a problem of major concern and was believed to be inevitable for a long time. In the process of engine development, the modification of fuel properties has lately gained great attention. In particular, the oxygenate fuel oxymethylene ether (OME) has proven potential to not only drastically reduce emissions, but possibly resolve the formerly inevitable trade-off completely.

The synthetic fuels dimethyl ether (DME) and polyoxymethylene dimethylether (POMDME or OME) are promising oxygenated fuels to meet the rising challenges of air pollution control, CO2-neutrality, and sustainability. The sootless combustion and high ignitability of DME and OME represent ideal properties for an application in diesel engines. However, recent investigations of oxygenates reported an increase of nanoparticles, which are known to have fatal effects on human’s health. Besides nanoparticles, ongoing discussions about future emission legislation focus on a drastic reduction of NOx. For this reason, the present work investigates different measures to reduce NOx emissions using DME/OME and a paraffinic diesel fuel (PDF) as reference. Different rail pressures, exhaust gas recirculation (EGR) rates, and injection timings are evaluated, considering the effectivity on NOx reduction and the impact on other emissions, especially on nanoparticles.

In this study, a fully optically accessible single-cylinder research engine is the basis for the visualization and generation of extensive knowledge about the in-cylinder processes of mixture formation, ignition and combustion of oxygenated synthetic fuels. Previous measurements in an all-metal engine showed promising results by using a mixture of dimethyl carbonate and methyl formate as a fuel substitute in a DISI-engine. Lower THC and NOx emissions were observed along with a low PN-value, implying low-soot combustion. The flame luminosity transmitted via an optical piston was split in the optical path to simultaneously record the natural flame luminosity with an RGB high-speed camera. The second channel consisted of OH*-chemiluminescence recording, isolated by a bandpass filter via an intensified monochrome high-speed camera.