Search Results

Gasoline Particulate Filters (GPF), are universally acknowledged as a reliable and high cost effective emission control technology for particulate mass (PM) and particulate number (PN). Bare GPFs can be modified by coating with catalytic washcoat to provide emission reduction for THC, CO and NOx while back pressure (BP) and filtration efficiency (FE) might be influenced. In this study, a four cylinder China 6B calibrated 1.6 L TGDI (turbo gasoline direct injection) vehicle was used to evaluate various catalyst combinations in the close-coupled and underfloor locations. In the close-couple 1 position (CC1), PGM loadings were varied on a 1 L TWC. Next in the close-coupled 2 position (CC2), coated and uncoated 1.4 L GPFs were evaluated. PGM loading was varied on the coated GPFs using 300/8 high porosity substrates. The uncoated GPFs used a 200/8 low porosity substrates. In the underfloor location, PGM loadings were varied on two 0.5 L TWC catalysts.

Beside the traditional prediction of stresses and verification by mechanical testing the optimization of cylinder liner bore distortion is one of today's most important topics in crankcase structure development. Low bore distortion opens up potentials for optimizing the piston group. As the piston rings achieve better sealing characteristics in a low deformation cylinder liner, oil consumption and blow-by are reduced. For unchanged oil consumption and blow-by demands, engine friction and subsequently, fuel consumption could be reduced by decreasing the pre-tension of the piston rings. From the acoustical point of view an optimization of piston-slap noise is often based on an optimized bore distortion behavior. Apart from basics to the behavior of liner bore distortion the paper presents advanced analytical and empirical methods for detailed prediction, verification and optimization of bore distortion taking into account the effective engine operation conditions.

The CO2 reduction request for automotive industry promotes the efforts on the engine thermal efficiency improvement. The goal of this research is to improve the thermal efficiency on an extremely downsized 3-cylinder 1.0 L turbocharged gasoline direct injection engine. Effects of compression ratio, exhaust gas recirculation (EGR), valve timing and viscosity of oil on fuel economy were studied. The results show that increasing compression ratio, from 9.6 to 12, can improve fuel economy at relative low load (below 12 bar BMEP), but has a negative effect at high load due to increased knock intensity. EGR can significantly reduce the pumping loss at low load, optimize combustion phase and reduce exhaust gas temperature. Therefore, the fuel consumption is reduced at all test points. The average brake thermal efficiency (BTE) benefit percentage is 3.47% with 9.6 compression ratio and 5.33 % with 12 compression ratio.

Because of increasing stresses in combustion engines and critical comfort requirements of engine warm-up behavior, FEV has placed a special emphasis on solving cooling system problems. In addition to 3D-CFD calculations and special FEV measurement techniques - such as fiber optical cavitation detection, instationary heat balance measurements during warm-up, etc. - FEV has developed a 1D computer code, known as ‘COOL’, to optimize cooling systems already during the engine design phase or to analyse and eliminate weaknesses in the coolant circuit of existing engines. Beside the algorithm and structure of COOL the paper mainly presents the analysis capabilities of the code. In this connection the emphasis is placed on examples to the current OEMs problem: transient warm-up of DI-diesel engines. The COOL-code is so far a unique CAE tool which exclusively has been applied to projects conducted by FEV. Because of the increasing demand it is planned to commercialize the code in 1998.

Modern passenger car engines are designed to operate at increasingly higher rated engine speeds with higher thermal loads. To reduce engine weight and length, the engines are usually siamesed without a cooling path between the cylinder liners. This leads to high temperatures in the siamesed area and to an increase in liner deformation. The distortion of the cylinder liners of internal combustion engines has a significant affect on engine operation. It can affect the oil consumption, the blow-by, the wear behavior and, due to friction, the fuel consumption. In order to achieve future requirements regarding exhaust emissions and fuel consumption, the development of low distortion engine blocks will play a significant role.

In recent years, more attention has been focused on environment pollution and energy source issues. As a result, increasingly stringent fuel consumption and emission legislations have been implemented all over the world. For automakers, enhancing engine’s efficiency as a must contributes to lower vehicle fuel consumption. To reach this goal, Geely auto started the development of a 3-cylinder 1.0L turbocharged direct injection (TGDI) gasoline engine to achieve a challenging fuel economy target while maintaining fun-to-drive and NVH performance. Demanding development targets for performance (specific torque 205Nm/L and specific power 100kW/L) and excellent part-load BSFC were defined, which lead to a major challenge for the design of the combustion system. Considering air/fuel mixture, fuel wall impingement and even future potential for lean burn combustion, a symmetrical layout and a central position for the injector with 200bar injection pressure was determined.

In recent years, more attention has been focused on environment pollution and energy source issues. As a result, increasingly stringent fuel consumption and emission legislations have been implemented all over the world. For automakers, enhancing engine’s efficiency as a must contributes to lower vehicle fuel consumption. To reach this goal, Geely auto started the development of a 3-cylinder 1.0L turbocharged direct injection (TGDI) gasoline engine to achieve a challenging fuel economy target while maintaining fun-to-drive and NVH performance. Demanding development targets for performance (specific torque 205Nm/L and specific power 100kW/L) and excellent part-load BSFC were defined, which lead to a major challenge for the design of engine systems, especially for combustion system.

The fuel consumption and the emissions of modern passenger cars are highly affected by the fluid and material temperatures of the engine. Unfortunately, the high thermal efficiencies of Direct Injection (DI) Diesel and Spark Ignition (SI) engines cause in many driving situations low heat transfer to the engine components and especially to the oil and the coolant. In these conditions the normal operating temperatures are not achieved. Especially at low ambient temperatures and low engine loads the requirement of a comfortable cabin heating and a fast warm-up of engine oil and coolant cannot be satisfied simultaneously. To reach the required warm-up performance, an Exhaust Heat Recovery System (EHRS) will be demonstrated. Further design and optimization processes for modern cooling systems in fuel-efficient engines require numerical and experimental investigations of supplemental heater systems to meet all requirements under all circumstances.

Gasoline Direct Injection (GDI) engines show advantages in reducing fuel consumption and gaseous pollution emissions when compared to Port Fuel Injection (PFI) engines. However, particulate matter emissions are an essential issue for GDI engine development due to increasingly stringent worldwide emission regulations. Previous studies have shown that gasoline fuel compositions, as well as deposits formed in GDI fuel injectors, can affect emissions in the GDI engine. In this work, the impact of gasoline fuel properties on forming injector deposits and the resulting effect on particulate emissions were investigated using a modern Chinese GDI engine. Six test fuels with different properties involving changes in olefins, aromatics, heavy (C9/C9+) aromatics, T90 and deposit control additive (DCA) were prepared based on the gasoline survey results from the Chinese gasoline fuel market and the China 6 gasoline fuel standard limits.

A higher octane quality fuel used in premium-recommended vehicles has the potential for delivering better acceleration and power. Octane number is a standard measure for the anti-knock quality of a gasoline fuel. A higher octane number fuel can withstand more compression before detonation (or knock). Higher compression ratios directly correlate with engine power and thermodynamic efficiency. Hence engines that are designed for higher octane or premium grade fuels should typically develop higher power by extracting more from the calorific value of the fuel. However, in the case of premium-recommended vehicle models that are designed to run even on lower octane fuels, the extent of performance benefits of using premium grade higher octane fuels can be deciphered via vehicle testing. In this regard, two gasoline fuels with anti-knock index values (AKI) of 87 and 91 respectively were compared in five premium-recommended vehicles for acceleration and power benefits.

Fuel consumption of a modern combustion engine is significantly influenced by the mechanical friction losses. Particularly in typical city driving, the reduction of the engine friction losses offers a remarkable potential in emission and fuel consumption reduction. The analysis of the engine friction distribution of modern engines shows that the piston group has a high share at total engine friction. This offers a high potential to optimize piston group friction. The paper presents results of recent research and development work in the field of the tribological system piston/piston ring/cylinder bore.

Particulate mass (PM) emissions from DISI engines can be reduced via fuels additive technology that facilitates injector deposit clean-up. A significant drawback of DISI engines is that they can have higher particulate matter emissions than PFI gasoline engines. Soot formation in general is dependent on the air-fuel ratio, combustion chamber temperature and the chemical structure and thermo-physical properties of the fuel. In this regard, PM emissions and DISI injector deposit clean-up were studied in three identical high sales-volume vehicles. The tests compared the effects of a fuel (Fuel A) containing a market generic additive at lowest additive concentration (LAC) against a fuel formulated with a novel additive technology (Fuel B). The fuels compared had an anti-knock index value of 87 containing up to 10% ethanol. The vehicles were run on Fuel A for 20,000 miles followed by 5,000 miles on Fuel B using a chassis dynamometer.

This work compared the piston deposit ratings in an engine when it was run on gasoline with a high concentration of deposit control additive (DCA) versus gasoline with a low concentration of additive. The additives came from different sources and contained detergents with different functional groups. The engine was a Ford V-8 PFI engine, which is used in ASTM D6593, the Sequence VG test. The experimental procedure followed the ASTM protocol, except for the fuel, which was treated with additives. Deposit ratings were better, at 95% confidence, in the tests using a high concentration of additive versus the tests using a low concentration.

In order to meet increasingly stringent emission regulations and reduce fuel consumption, development of modern powertrain is becoming more complicated, combining many advanced technologies. Gasoline engine downsizing is already established as a proven technology to reduce vehicle fleet CO2 emissions. Compressed natural gas (CNG) offers increased potential to further reduce both tailpipe CO2 and other regulated exhaust gas emissions without compromising driving performance. In this study, a turbocharged CNG port fuel injection (PFI) engine was developed based on gasoline version. Making most use of positive fuel properties of CNG, the paper quantifies the performance characteristics of downsized CNG engine considering reduced knock sensitivity, adaption of compression ratio and combustion efficiency. While peak cylinder pressure was controlled below 120 bar, peak torque 180Nm, same level as gasoline variant, was realized from 3000rpm.